Related Manuals for NEO 15501
Summary of Contents for NEO 15501
- Page 1 15501 BETMAKERS TOT KIOSK INSTRUCTION TO REMOVE / REPLACE 15.6" LCD SCREEN 15501-ML005 REV01 ECN 6609...
- Page 2 LCD Screen downwards to a full stop position. STEP 4 Holding the bottom of the 15.6” LCD Screen, push the 15.6” LCD Screen downwards to a full stop position to access the Screen Hinge Cover. Page 2 15501-ML005 REV01 ECN 6609...
-
Page 3: Lcd Screen
& pull upwards to clear the Looms & retainment tabs. STEP 7 Remove 1x 15.6” LCD Screen HDMI plug (with NEO marking) from the 15.6” port in location shown. STEP 8 To assist, use a Flat Screwdriver to gently twist &... - Page 4 STEP 11 Place the removed LCD Screen onto a flat table with the Rear Cover facing upwards. MSR + NFC Payment Module (part# 15501-SPER002) removal: STEP 12 Using a 1/4" Drive TORX Bit Socket T8 with Ratchet & Extension or T8 TORX L-...
- Page 5 NFC Reader Retain for fitment into the replacement 15.6” LCD Screen. Barcode Scanner Module (part# 15501-SPER003) removal: STEP 14 Using a 1/4" Drive TORX Bit Socket T8 with Ratchet & Extension or T8 TORX L- Shaped Wrench, remove 2x Screws from the Barcode Scanner Module (part# 15501- SPER003).
- Page 6 Screen onto a flat table with the Rear Cover facing upwards. STEP 18 To re-install the MSR + NFC Payment Module (part# 15501-SPER002) into the replacement 15.6” LCD Screen, follow Steps 12 to 13 in reverse. STEP 19 When installing the MSR + NFC Payment Module, check that the Loom plugs are installed without “cross-over”.
- Page 7 Scanner Module, follow Steps 14 to 15 in reverse. STEP 21 When installing the Barcode Scanner Module, check that the Loom plug is installed as removed. 15.6” LCD Refer to image for further information. Rear Cover Barcode Scanner Module Page 7 15501-ML005 REV01 ECN 6609...
- Page 8 15.6” LCD Screen is fully supported prior to installing the Screws. Failure will result in the Screen falling causing damage. STEP 23 Install Loom part# 15501-LM011 connector into port highlighted. STEP 24 Install Loom part# 15501-LM007 connector into port highlighted.
- Page 9 STEP 26 Using Side Cutters, cut & remove 1x “STEP” of the sleeve as shown. Discard waste. Cut 1x places STEP 27 At the completion of the cutting, check that the sleeve looks like this “NO step” only. NO step Page 9 15501-ML005 REV01 ECN 6609...
- Page 10 15.6” LCD Screen performed by trained service personnel only. Replacing the 15.6” LCD Screen (continued) STEP 28 Install HDMI Loom (with Neo marking) connector into port highlighted. Carefully route the Loom in a upwards direction with a “small loop” to allow return downwards as shown.
- Page 11 LCD. MSR + NFC Payment Module (part# 15501-SPER002) test: STEP 33 Validate that the MAGSWIPE & NFC are working correctly. Select “START”.
- Page 12 Ensure that the NFC Card is not too far as the NFC Reader might not be able to read the card. STEP 38 As the card is present near the reader the application should read “Connected” as shown. **END OF TEST** Page 12 15501-ML005 REV01 ECN 6609...
- Page 13 15.6” LCD Screen performed by trained service personnel only. Replacing the 15.6” LCD Screen (continued) Barcode Scanner Module (part# 15501-SPER003) test: STEP 39 Test the Barcode Scanner by placing a Barcode underneath to scan. Note: The Light on the Barcode Scanner should turn “ON”...
- Page 14 • Provide serial# details to Neo. Prepare to return the removed 15.6” LCD Screen by wrapping protective film • around the screen. Place the screen in the supplied Neo packaging. Return screens to Neo. Page 14 15501-ML005 REV01 ECN 6609...
Need help?
Do you have a question about the 15501 and is the answer not in the manual?
Questions and answers