Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Elite ProAV Manuals
  4. Projector Accessories
  5. Golf Bay Pro Series
  6. User manual and assembly instructions

Elite ProAV Golf Bay Pro Series User Manual And Assembly Instructions

Multi-sport/golf simulation impact projector screen
Hide thumbs

Advertisement

Quick Links

Download this manual
Product Description: The Golf Bay Pro Series is an enclosed golf and sport simulator impact screen that utilizes our
three-layer ImpactWhite® 1145. It includes a full frame assembly kit for permanent installation in dedicated spaces.
Please read through this user guide before utilizing the screen. Correct usage and maintenance will ensure a
long product life.
ImpactWhite®1145 material tips and precautions
• Handle with caution, material is subject to static electricity.
• Wear gloves and unroll the material on a clean surface.
• Make sure to use the correct side. The ImpactWhite® 1145 screen has a front and back side.
• Folding lines/wrinkles are normal due to the nature of the material structure and packaging but may be removed
with a steamer and/or light ironing set to no higher than Polyester.
• Make sure to allow proper distance for swing range to protect children, pets, ceilings, walls, windows, or any
other property.
• Dust, dirt and scratches on the projection surface will affect the picture quality, please take note of the points
below to prevent that from occurring:
1. Do not touch the projection surface with your hands.
2. Do not write or draw on the projection surface.
3. Do not point at the projection surface with your fingers or sharp objects; this will damage the screen material.
4. Use a soft bristle brush or dry microfiber cloth to remove dust from the screen surface.
5. Do NOT use any solutions, chemical cleaning agents, alcohol, or abrasive to clean the screen surface.
6. When cleaning the projection surface, use a soft cloth dampened with warm water to remove any traces.
7. Do NOT rub or apply pressure when cleaning the surface.
We consider our impact screens a wearable item and the life of them will vary according to
their use. Avoid using golf balls with scuffs or markings to maximize the life of the screen.
Rev.08052024JA
User Guide & Assembly Instructions
Visit
www.eliteproav.com
If possible, use new golf balls.
1
Golf Bay Pro Series
Multi-Sport/Golf Simulation
Impact Projector Screen
for the latest updated version.
U00269
V1.1
www.eliteproav.com

Advertisement

loading
Need help?

Need help?

Do you have a question about the Golf Bay Pro Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Elite ProAV Golf Bay Pro Series

Summary of Contents for Elite ProAV Golf Bay Pro Series

  • Page 1 Product Description: The Golf Bay Pro Series is an enclosed golf and sport simulator impact screen that utilizes our three-layer ImpactWhite® 1145. It includes a full frame assembly kit for permanent installation in dedicated spaces.
  • Page 2 Hardware Parts List Item Part List GSB10x10 GSB13x10 M8 hex screw Three-way corner connector L-shaped connector Straight connector T-shaped connector Ball bungee M8 Hex Wrench Cable tie Vertical frame (30x30x1450mm) Horizontal frame (30x30mm) 1480mm - 6pcs 1980mm - 6pcs Inner frame (30x30x1180mm) Foam tube-1450mm Foam tube 1500mm-4pcs...

  • Page 3: Exploded Diagram

    Exploded Diagram Assembly Instructions Step 1: Assemble all four vertical support frames (I) using the straight connectors (D) and fasten them using the M8 Hex Wrench (G) and M8 hex screws (A). We will refer to them as ID. Rev.08052024JA U00269 www.eliteproav.com...
  • Page 4 Step 2: Connect two horizontal frames (J) together using the t-shaped connector (E). Then attach two three-way corner connectors (B) at each end to join frames ID and J together as shown below. Fasten with M8 Hex Wrench (G) and M8 hex screws (A). Screw holes must face inside.
  • Page 5 Step 4. Attach a three-way corner connector (B) to inner frame (K) on all corners and attach a vertical frame (ID) Next, attach a T-shaped connector (E) to the center inner frame (K), attach horizontal frame (J) to B and E connectors and fasten with M8 Hex Wrench (G) and M8 hex screws (A).
  • Page 6 Foam tube application Step 6. Use cable tie(H) to secure the foam tube(L)(M)(N) to the frame Notch facing back(M)(N) Notch facing front (N) Notch facing up Wrap a cable tie (H) around both ends and the middle bars. Trim off any excess with a pair of scissors.
  • Page 7 Golf Screen Installation Step 7. Preparing to hang the golf screen on the frame. 7-1. Distinguishing the front and back side first. Projection (Front) Side Back Side 7-2. Using the ball bungees (F) 1. Insert the loop end of the 3.
  • Page 8 Step 8. Lift and stand up the frame. Continue attaching the Golf screen to the frame in the following order. Use only one ball bungee at the bottom corners. Enclosure panels installation Step 9. Left and Right Enclosure panels 9-1. Distinguish the front side and back sides. The front has the loop (fuzzy) and the back has the hook (rough). Loop side = Front Velcro should be pulled apart.
  • Page 9 9-2 Attach the top of the panel first. Assure a tight and taut finish. Velcro strip faces outside. Attach the top flap of the panel with the velcro. 9-3. Attach the bottom side. Assure a tight and taut finish. Pull the bottom of the panel under the frame and attach it with the velro.
  • Page 10 9-5 Lastly, attach the edge with velcro. 9-6. Repeat step 9-1 ~ 9-4 for the other side. Step10. Top enclosure panel 10-1. Hang the top panel (d), pull it tightly and attach it to the Velcro strip on each side panel. Velcro strip Attach to align with the bottom edge of the Velcro strip.
  • Page 11 Panel should go over the middle bar. 10-2. Insert the ball bungees (G) through the grommets and attach to the back of the frame. 10-3. Loop the front velcro over the frame bar to attach it. Rev.08052024JA U00269 www.eliteproav.com...
  • Page 12 Golf Screen side border panels Step11. Attach the side border panels (e /f) on both sides of the golf screen. Distinguish between inner and outer side. Side with two Velcro strips is the inner side. Velcro side face up is the outer side. 11-1.
  • Page 13 Golf Screen top border panel The 4 sides with Velcro strips Step12. Attach the top border panel (e) at the top of the golf screen. are the loop (fuzzy) side. 12-1. Fold the black cover cloth to obtain the middle point of the panel. Middle point 12-2.
  • Page 14 13-2. Attach the left and right side black backing panels (h) from the edge to the middle. Attach direction Attach direction. Attach excess on the middle panel. For a local Elite ProAV contact or Technical Support, please visit www.elitesproav.com Rev.08052024JA U00269...