Spirent XD5 Setup Manual

Spirent Setup Guide:
Multilink Duplexing Test System - Vertex
Equipment Layout
XD5 XD5
MULTILINK DUPLEXER MULTILINK DUPLEXER
CONFIGURATION CONFIGURATION
Z1 Z1
U1 U1 U2 U2 Q1 Q1 Q2 Q2
U3 U3 U4 U4
U5 U5 U6 U6 Z3 Z3
U7 U7 U8 U8 Q3 Q3 Q4 Q4
XD5 XD5
MULTILINK DUPLEXER MULTILINK DUPLEXER
CONFIGURATION CONFIGURATION
Z1 Z1
U1 U1 U2 U2 Q1 Q1 Q2 Q2
U3 U3 U4 U4
U5 U5 U6 U6 Z3 Z3
U7 U7 U8 U8 Q3 Q3 Q4 Q4
I/O 1 I/O 1 OUT 2 OUT 2 I/O 3 I/O 3
SPIRENT SDE-RFUD6 SPIRENT SDE-RFUD6
I/O 1 I/O 1 OUT 2 OUT 2 I/O 3 I/O 3
SPIRENT SDE-RFUD6 SPIRENT SDE-RFUD6
I/O 1 I/O 1 OUT 2 OUT 2 I/O 3 I/O 3
SPIRENT SDE-RFUD6 SPIRENT SDE-RFUD6
I/O 1 I/O 1 OUT 2 OUT 2 I/O 3 I/O 3
SPIRENT SDE-RFUD6 SPIRENT SDE-RFUD6
Vertex Channel Emulator Vertex Channel Emulator
+1 800-SPIRENT – www.spirent.com
STATUS STATUS
X1 X1 M1 M1 M2 M2 M3 M3 M4 M4
Z2 Z2
POWER POWER
X2 X2 M5 M5 M6 M6 M7 M7 M8 M8
Z4 Z4 I I
O O
STATUS STATUS
X1 X1 M1 M1 M2 M2 M3 M3 M4 M4
Z2 Z2
POWER POWER
X2 X2 M5 M5 M6 M6 M7 M7 M8 M8
Z4 Z4 I I
O O
SLOT SLOT
OUT 4 OUT 4 I/O 1 I/O 1 OUT 2 OUT 2 I/O 3 I/O 3 OUT 4 OUT 4
1 1 2 2
BIDIRECTIONAL RF MODULE BIDIRECTIONAL RF MODULE SPIRENT SDE-RFUD6 SPIRENT SDE-RFUD6 BIDIRECTIONAL RF MODULE BIDIRECTIONAL RF MODULE
I/O 1 I/O 1 OUT 2 OUT 2 I/O 3 I/O 3 OUT 4 OUT 4
OUT 4 OUT 4
3 3 4 4
SPIRENT SDE-RFUD6 SPIRENT SDE-RFUD6 BIDIRECTIONAL RF MODULE BIDIRECTIONAL RF MODULE
BIDIRECTIONAL RF MODULE BIDIRECTIONAL RF MODULE
OUT 4 OUT 4 I/O 1 I/O 1 OUT 2 OUT 2 I/O 3 I/O 3 OUT 4 OUT 4
5 5 6 6
BIDIRECTIONAL RF MODULE BIDIRECTIONAL RF MODULE
SPIRENT SDE-RFUD6 SPIRENT SDE-RFUD6 BIDIRECTIONAL RF MODULE BIDIRECTIONAL RF MODULE
OUT 4 OUT 4 I/O 1 I/O 1 OUT 2 OUT 2 I/O 3 I/O 3 OUT 4 OUT 4
7 7 8 8
BIDIRECTIONAL RF MODULE BIDIRECTIONAL RF MODULE SPIRENT SDE-RFUD6 SPIRENT SDE-RFUD6 BIDIRECTIONAL RF MODULE BIDIRECTIONAL RF MODULE
SYNC IN SYNC IN SYNC OUT SYNC OUT
AUX 1 AUX 1
AUX 2 AUX 2 AUX 3 AUX 3
9 9 10 10
1 1 2 2 3 3 4 4
SPIRENT SDE-TC4 SPIRENT SDE-TC4 TIMING SOURCE MODULE TIMING SOURCE MODULE
STATUS STATUS
Page 1 of 11
ATTENTION!
Perform the following procedure after you have
completed all cable routing.
Applying Power to the System
Instruction
1 Make sure the loopback cable is connected on the rear panel of the
Vertex instrument.
2 Connect the AC power cords to all instruments.
3 Plug the AC power cords into the wall outlet.
Plug the Vertex instrument directly into the wall outlet on an individual
4
branch circuit.
5 Switch on the Vertex instrument.
6 Switch on XD5-A.
7 Switch on XD5-B.
8 Ensure each instrument powers up properly.
NOTE:
If only one XD5 is in use, it must be configured as an XD5-A
unit. If two XD5s are in use by one Vertex, those units must be
configured as XD5-A and XD5-B respectively.
Connecting two XD5s of similar name type assignment to a
single Vertex will cause IP conflict problems. To reconfigure
the XD5's type, you must use the Vertex GUI. See the Vertex
user manual for more information.
Information subject to change.
71-008027.A4