Related Manuals for Optika Italy M-635
Summary of Contents for Optika Italy M-635
- Page 1 ACCESSORIES Series INSTRUCTION MANUAL Model M-635 M-666 M-1144 M-1190H ST-666 Ver. 1.0 2024...
-
Page 2: Table Of Contents
ST-666 Unpacking Intended use Symbols and conventions Instrument description M-635 M-666 M-1144 M-1190H ST-666 Assembling Stage assembling 8.1.1 M-635 / M-1190H 8.1.2 M-666.290 8.1.3 M-666 8.1.4 M-1144 8.1.5 ST-666 Use of the heating stage Switching the stage Temperature setting Maintenance... -
Page 3: Warning
Warning This illuminator is a scientific precision instrument designed to last for many years with a minimum of maintenance. It is built to high optical and mechanical standards and to withstand daily use. We remind you that this manual contains important information on safety and maintenance, and that it must therefore be made accessible to the instrument users. -
Page 4: Package Content
Package content M-635 ① ② ③ ① Heating stage (installed on the microscope) ③ Power supply ② Temperature controller M-666 / M-666.290 ① ② ③ ① Heating stage (installed on the microscope) ③ Power supply ② Temperature controller Page 4... -
Page 5: M-1144
M-1144 ② ① ③ ① Heating stage ③ Power supply ② Temperature controller M-1190H ① ② ③ ① Heating stage ③ Power supply ② Temperature controller Page 5... -
Page 6: St-666
ST-666 ② ① ③ ① Heating stage ③ Power supply ② Temperature controller Page 6... -
Page 7: Unpacking
Unpacking The device is housed in a moulded Styrofoam container. Remove the tape from the edge of the container and lift the top half of the container. Take some care to avoid that the optical items (objectives and eyepieces) fall out and get damaged. Using both hands (one around the arm and one around the base), lift the illuminator from the container and put it on a stable desk. -
Page 8: Instrument Description
Instrument description M-635 SLIDE HOLDER THERMAL STAGE CONNECTION CABLE X/Y MOVEMENT KNOBS DISPLAY TEMPERATURE SETTING KNOB M-666 THERMAL STAGE CONNECTION CABLE DISPLAY TEMPERATURE SETTING KNOB Page 8... -
Page 9: M-1144
M-1144 SLIDE HOLDER THERMAL STAGE X/Y MOVEMENT KNOBS DISPLAY CONNECTION CABLE TEMPERATURE SETTING KNOB M-1190H SLIDE HOLDER THERMAL STAGE X/Y MOVEMENT KNOBS CONNECTION CABLE DISPLAY TEMPERATURE SETTING KNOB Page 9... -
Page 10: St-666
ST-666 DISPLAY CONNECTION CABLE STAGE CLIPS TEMPERATURE SETTING KNOB THERMAL STAGE All models: temperature controller back panel MAIN SWITCH HEATING STAGE CABLE PLUG POWER SUPPLY PLUG Page 10... -
Page 11: Assembling
Assembling Stage assembling 8.1.1 M-635 / M-1190H The stage comes already installed on the microscope from the factory. No further installation procedure is required. 8.1.2 M-666.290 The stage comes already installed on the microscope from the factory. No further installation procedure is required. -
Page 12: Use Of The Heating Stage
Use of the heating stage Switching the stage 1. Operate on the main switch ① to turn ON / OFF the control- ler. (Fig. 5) ① F ig. 4 ig. 4 Temperature setting 1. Operate on the temperature setting knob ② to set the de- sired temperature. -
Page 13: 10. Maintenance
10. Maintenance Microscopy environment This microscope is recommended to be used in a clean, dry and shock free environment with a temperature of 5°-40°C and a maximum relative humidity of 75 % (non condensing). Use a dehumidifier if needed. To think about when and after using the microscope •... -
Page 14: Equipment Disposal
Equipment disposal Art.13 Dlsg 25 July 2005 N°151. “According to directives 2002/95/EC, 2002/96/EC and 2003/108/EC relating to the reduc- tion in the use of hazardous substances in electrical and electronic equipment and waste disposal.” The basket symbol on equipment or on its box indicates that the product at the end of its useful life should be collected sep- arately from other waste.
Need help?
Do you have a question about the M-635 and is the answer not in the manual?
Questions and answers