Epoch Design Nara Platform Bed 5481 Quick Assembly Instructions

2/3
3/3
1/3
E D
POCH ESIGN
, LLC
Congratulations on the purchase of your Epoch Design Nara Bamboo Platform Bed. This bed has
been crafted to the highest standards of quality and safety and will give you many years of enjoyment and
practical use. Since this is a natural bamboo product there will be variations in color and grain, and minor
grain checking may occur. This is normal and does not compromise the integrity of your piece. Variation in
the character of bamboo is integral to the beauty and appeal of this furniture, and distinguishes it from
lower quality materials.
On this insert you will nd a list of the hardware and platform bed parts necessary for assembly, as
well as detailed instructions. Assembly is quite simple and requires only a at head screwdriver and a
Phillips head screwdriver. The use of a power drill with a Phillips head attachment with the clutch set on low
is helpful but not necessary. Assembly will be most easily accomplished if you take the time to carefully sort
Figure 4
the hardware and familiarize yourself with the function of each piece.
STEP 2
Insert all 4 of the threaded steel dowels into the
footboard by hand. Figure 2.
30x 30mm Wood
Screws
Slide the footboard toward the side rails so that the dowels go through
the holes at the end of the side rails. Figure 3.
Slide the bracket over the dowel as shown. Hand tighten the nut behind the bracket.
Use the wrench provided to tighten the nut. Figure 4.
STEP 5
Note: The narrow end of the nut should protrude through the bracket when fully tightened.
Lay out the slats evenly on bed,
After the footboard is fully attached tighten the 110 mm headboard bolts.
mm 10 20 30
strap side down.
1
1x Headboard
If you should require assistance with assembly, part replacement or any other matter, contact the
toll-free Epoch Design Service Center from anywhere in the Continental United States, Monday through
Friday, 9AM-5PM Paci c Standard Time at (800) 589-7990. You may also fax your request or comments to
(425) 284-0885 and/or email to info@epochbydesign.com and a service representative will respond.
Have a question? Need a part ASAP? Call 1-800-589-7990 or email info@epochbydesign.com. Have a question? Need a part ASAP? Call 1-800-589-7990 or email info@epochbydesign.com.
Figure 1
Nara Platform Bed
12x 15 mm Machine
Screws
4x 110mm Bolts
40 50 60 70
STEP 3
Using the 12 machine screws provided, attach the 2 steel center support
brackets (open end up) to the foot and head board as shown in Figure 5.
1x Center Support
HAVE QUESTIONS OR CONCERNS? CALL US FIRST: 1-800-589-7990
Copyright © 2018 Epoch Design™ All rights reserved
STEP 1
Using 4 x 110mm bolts and 4 x barrel nuts attach the
STEP 4
bed rails to the headboard as shown in Figure 1.
Insert the center support rail into
5481, 5482
the brackets as shown in Figure 6.
Note: Do one rail at a time and only
hand tighten the bolts at this time.
HARDWARE LIST
4x Barrel Nuts
1
1x Allen Wrench
80 90 100 110
PARTS LIST
2
2x Side Rails
Figure 3
Figure 6
4x Bracket
Assemblies
2x Center
Support
Brackets
Using the 30mm slat screws provided, screw the slat
closest to the headboard to the two outside slat rails.
Secondly screw the slat closest to the
footboard to the two outside rails.
2
Figure 5
Then proceed to secure the
remaining slats in any order.
1x Footboard
28-Sept-2018
28-Sept-2018
28-Sept-2018
Figure 2
1x Wrench
15x Slats