Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for D-Link DSL-302T
Summary of Contents for D-Link DSL-302T
-
Page 1: Adsl Modem
DSL-302T ADSL Modem User’s Manual Edition (October 2004) 651DSL302T02... -
Page 2: Ce Mark Warning
- Consult the dealer or an experienced radio/TV technician for help. CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. DSL-302T DSL Modem User’s Guide... -
Page 3: Warranties Exclusive
Gerä tegewicht grő ß er 3kg ist eine Leitung nicht leichter als H05VV-F, 3G, 0.75mm2 einzusetzen. WARRANTIES EXCLUSIVE IF THE D-LINK PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER'S SOLE REMEDY SHALL BE, AT D- LINK'S OPTION, REPAIR OR REPLACEMENT. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. -
Page 4: Limitation Of Liability
This Warranty applies on the condition that the product Registration Card is filled out and returned to a D-Link office within ninety (90) days of purchase. A list of D-Link offices is provided at the back of this manual, together with a copy of the Registration Card. - Page 5 Spare parts and spare kits Ninety (90) days D-Link’ s sole obligation shall be to repair or replace the defective Hardware during the Warranty Period at no charge to the original owner or to refund at D-Link’ s sole discretion. Such repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office.
- Page 6 D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product. Repair by anyone other than D-Link or an Authorized D-Link Service Office will void this Warranty. Disclaimer of Other Warranties: EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED “AS-IS”...
-
Page 7: Table Of Contents
About This User’s Guide ... ix Before You Start ... ix Information Required for Installation ...x Installing the USB Driver... xii INTRODUCTION ... 1 Modem Description and Operation ... 1 Modem Features... 3 Standards Compatibility and Compliance... 4 Front Panel Display... 5 Rear Panel Connections ... - Page 8 Status... 34 Network Statistics ... 35 Connection Status ... 36 DHCP Clients... 37 Modem Status ... 38 Product Info..39 System Log ... 40 Help ... 41 TECHNICAL SPECIFICATIONS... 42 IP ADDRESS SETUP... 44 IP CONCEPTS ... 46 MICROFILTERS AND SPLITTERS ... 49...
-
Page 9: About This User's Guide
If you are using a computer with a functioning Ethernet port or an available USB port, the quickest and easiest way to set up the DSL-302T is to insert the Installation CD into the CD-ROM drive of your computer and follow the instructions provided in the Quick Installation Guide. -
Page 10: Information Required For Installation
VPI above to identify the data path between your ADSL service provider’s network and your computer. Information you will need to change settings on the DSL-302T Modem: This is the Username needed access the Modem’s management interface. When you attempt to connect to... - Page 11 ADSL connection in the future. Once you have the above information, you are ready to setup and configure your DSL-302T ADSL Modem. The Modem may be reset to its factory default settings by performing a Restore settings operation within the management interface (see below).
-
Page 12: Installing The Usb Driver
The CD-ROM shipped with the Modem contains the USB driver software. 1. Insert the DSL-302T Installation CD-ROM into the CD-ROM drive. 2. Connect the USB cable to the device. Within a few seconds you should see the “ Found New Hardware”... - Page 13 6. Check “ CD-ROM drives" (as shown above) if you are using the USB driver included on the CD-ROM that came with your Modem. Click Next. 7. Connect the Ethernet cable if you have not done so. 8. Connect the ADSL cable if you have not done so. Remember that most ADSL installations require a filter to divide the ADSL signal from the Plain-Old Telephone (POTS) signal.
-
Page 15: Introduction
The Modem is easy to install and use. The DSL-302T connects to single computer or an Ethernet LAN via a standard Ethernet interface. A single computer may also be connected through the USB port. The ADSL connection is made using ordinary twisted-pair telephone line with standard connectors. -
Page 16: Web Browser
DSL-302T ADSL Modem User’s Guide Web Browser Any common web browser can be used to configure the Modem using the web configuration management software. The program is designed to work best with more recently released browsers such as Opera, Microsoft Internet Explorer®... -
Page 17: Modem Features
Modem Features The DSL-302T ADSL Modem utilizes the latest ADSL enhancements to provide a reliable Internet portal suitable for most small to medium sized offices. DSL-302T advantages include: PPP (Point-to-Point Protocol) Security – The DSL-302T ADSL Modem supports PAP (Password Authentication Protocol) and CHAP (Challenge Handshake Authentication Protocol) for PPP connections. -
Page 18: Standards Compatibility And Compliance
Standards Compatibility and Compliance The DSL-302T complies with or is compatible with the following standards as recognized by their respective agencies. ITU G.992.2 (G.lite “ Splitterless ADSL”) compliant ITU-T Rec. I.361 compliant RFC 791 Internet Protocol compliant RFC 792 UDP compliant... -
Page 19: Front Panel Display
A solid green light indicates a valid link on startup. This light will blink when Ethernet: Link/Act there is activity currently passing through the Ethernet port. Steady green light indicates a valid USB connection. A blinking green light USB: Link/Act indicates activity on the USB interface. DSL-302T ADSL Modem User’s Guide... -
Page 20: Rear Panel Connections
USB driver ADSL port, connect ADSL cable here The Modem may be rebooted by disconnecting and then reconnecting the power. Note DSL-302T ADSL Modem User’s Guide Ethernet port, connect Ethernet cable here Factory Reset button... -
Page 21: Hardware Installation
Hardware Installation The DSL-302T maintains three separate interfaces, an Ethernet, a USB and an ADSL interface. Place the Modem in a location where it can be connected to the various devices as well as to a power source. The Modem should not be located where it will be exposed to moisture or excessive heat. -
Page 22: Network Connections
LAN to the Modem does not exceed 100 meters. Computer to Modem Connection Connect the Modem directly to a 10/100BASE-TX Ethernet port on a PC or notebook computer using the Ethernet cable provided as shown in this diagram. DSL-302T ADSL Modem User’s Guide... -
Page 23: Hub Or Switch To Modem Connection
If you wish to reserve the uplink port on the switch or hub for another device, connect to any on the other MDI-X ports (1x, 2x, etc.) with a crossed cable. DSL-302T ADSL Modem User’s Guide... -
Page 24: Configuring The Modem For The First Time
IP settings for the other computers. However, you cannot use the same IP address since every Note computer must have its own IP address that is unique on the local network. DSL-302T ADSL Modem User’s Guide... - Page 25 Use the following steps to configure a computer running Windows XP to be a DHCP client. From the Start menu on your desktop, go to Settings, then click on Network Connections. In the Network Connections window, right-click on LAN (Local Area Connection), then click Properties. DSL-302T ADSL Modem User’s Guide...
- Page 26 DSL-302T ADSL Modem User’s Guide 3. In the General tab of the Local Area Connection Properties menu, highlight Internet Protocol (TCP/IP) under “ This connection uses the following items:” by clicking on it once. Click on the Properties button.
-
Page 27: Windows 2000
1. In the Control Panel, double-click the Network and Dial-up Connections icon. 2. In Network and Dial-up Connections window, right-click the Local Area Connection icon, and then select Properties. 3. In the Local Area Connection Properties dialog box, select Internet Protocol (TCP/IP), and then click Properties. DSL-302T ADSL Modem User’s Guide... -
Page 28: Windows 95 And Windows 98
6. Click OK to return to the Network dialog box, and then click OK again. You may be prompted to install files from your Windows 95/98 installation CD. Follow the instructions to install the files. 7. Click OK to restart the PC and complete the TCP/IP installation. DSL-302T ADSL Modem User’s Guide... -
Page 29: Access The Configuration Manager
2. Select the network component labeled TCP/IP, and then click Properties. 3. If you have multiple TCP/IP listings, select the listing associated with your network card or adapter. 4. In the TCP/IP Properties dialog box, click the IP Address tab. -
Page 30: Home
Do not confuse the user name and password used to access the web-based manager with the ADSL account user name and password needed for PPP Note connections to access the service provider’s network. DSL-302T ADSL Modem User’s Guide Figure 3-1. Home - Login window... -
Page 31: Configure The Modem
DSL-302T ADSL Modem User’s Guide Configure the Modem The first page that appears after you successfully login displays information about the Modem and its connection status. Tabs across the top of the screen show other available menus: Home, Setup, Tools, Status, and Help. -
Page 32: Setup
DSL-302T ADSL Modem User’s Guide Setup The Setup window offers links to menus to configure settings for the LAN (Local Area Network) and for the WAN (Wide Area Network) setup. The first menu you see when clicking the Setup tab is the DSL Setup menu. -
Page 33: Configure A New Connection
DSL-302T ADSL Modem User’s Guide Configure a New Connection The default connection protocol used for the Modem is Point-to-Point Protocol over ATM (PPPoA). The menu used to configure ADSL service using this protocol is the menu you see when clicking on the Connection button under WAN Setup on the left side of the window. - Page 34 After a few seconds the new connection you just configured will become the active connection for the Modem. 10. To make your temporarily saved connection permanent, click the Save All button in the System Commands window on the Tools tab. DSL-302T ADSL Modem User’s Guide...
- Page 35 6. Supply a Username and Password used to verify the identity of your account. These are usually provided by your ISP. DSL-302T ADSL Modem User’s Guide Change connection type here...
- Page 36 Modem act as a bridge, and just passes packets across the DSL port. 1. Type in a Name in the space provided if you wish or leave the default name. 2. Make sure Bridge appears listed as the Type: of connection protocol used. DSL-302T ADSL Modem User’s Guide...
- Page 37 To configure the WAN connection for Static, perform the steps listed below. Some of the settings do not need to be changed the first time the device is set up, but can be changed later if you choose. DSL-302T ADSL Modem User’s Guide Figure 3- 7. Setup Static IP...
- Page 38 DSL-302T ADSL Modem User’s Guide 1. Click the Connection 1 button under WAN Setup to view the default PPPoA Connection Setup configuration menu. 2. Select Static from the Type: pull-down menu. This action will change the menu so it offers different settings for configuration.
-
Page 39: Web-Based Management
Web-based Management The DSL-302T offers a web-based (HTML) graphical user interface allowing users to manage the Modem from anywhere on the LAN using a standard browser. A web browser is used to communicate directly with the Modem and make changes to the configuration or monitor status. -
Page 40: Dhcp Configuration
Type in the last address of the contiguous IP address range to be used by End IP the Modem for DHCP function. This specifies the amount of time (in seconds) a client can lease an IP Lease Time address, from the dynamically allocated IP pool. DSL-302T ADSL Modem User’s Guide... -
Page 41: Management Ip
DSL-302T ADSL Modem User’s Guide Management IP The IP address of the modem may be changed, but remember to take note of the new settings. A valid IP address and subnet mask are needed to access the Web manager. Figure 4-2. Setup – Management IP window... -
Page 42: Tools
DSL-302T ADSL Modem User’s Guide Tools Changing the User Name and Password Before you configure the Modem and connect to the WAN, you should change the user name and password used to access the web-based manager. Click on the Tools tab to access the Tools menu. -
Page 43: Save All
Restore The DSL-302T can be reset to the default configuration for all settings using the Restore option. This will also change the both the LAN and WAN IP address of the device, so these will need to be reconfigured accordingly. -
Page 44: Remote Log
Add and IP address of a server or station used to log event messages sent from the Modem. Type an IP address in the Add an IP Address field and click the Add button to save the address on the list of logging destinations. DSL-302T ADSL Modem User’s Guide Figure 4-5. Tools – Remote Log window... -
Page 45: User Management
1. Type the current User Name in the entry field provided. 2. Type in the new Password in the entry field provided. 3. Type in the new password again in the Confirm Password field. 4. If desired, change the Idle Timeout value. 5. Click Apply. DSL-302T ADSL Modem User’s Guide... -
Page 46: Update Gateway
Use the Update Gateway feature to load the latest firmware for the device. You can obtain the latest version of the DSL-302T firmware by logging onto the D-Link web site at www.dlink.com. Save the latest firmware version to a file on your computer or an accessible TFTP server. -
Page 47: Ping Test
DSL-302T ADSL Modem User’s Guide Ping Test Figure 4-8. Tools – Ping Test window This window is used to test the connection path of the Modem to another networked device with an IP address. To Ping a device, first enter the IP address of the device that you wish to Ping into the first field, the Packet Size (in bytes) in the second field, and finally, enter the number of times you wish the Ping function to attempt a connection to the desired device into the third field. -
Page 48: Status
DSL-302T ADSL Modem User’s Guide Status Figure 4-9. Opening Status window Click the hyperlink for the desired Status window. -
Page 49: Network Statistics
DSL-302T ADSL Modem User’s Guide Network Statistics Figure 4-10. Status – Network Statistics window Choose the desired interface at the top of the window and then click Refresh to view Ethernet network statistics. -
Page 50: Connection Status
DSL-302T ADSL Modem User’s Guide Connection Status Figure 4-11. Status – Connection Status window Click Refresh to view connection status information. -
Page 51: Dhcp Clients
DSL-302T ADSL Modem User’s Guide DHCP Clients Figure 4-12. Status – DHCP Clients window This window displays the status of all current DHCP clients. -
Page 52: Modem Status
DSL-302T ADSL Modem User’s Guide Modem Status Figure 4-13. Status – Modem Status window This window displays the status of the modem as well as DSL statistics. -
Page 53: Product Info
DSL-302T ADSL Modem User’s Guide Product Info. Figure 4-14. Status – Product Info. window This window displays product information including software versions. -
Page 54: System Log
DSL-302T ADSL Modem User’s Guide System Log Figure 4-15. Status – System Log window Click Refresh to get the most current system log information. -
Page 55: Help
DSL-302T ADSL Modem User’s Guide Help Figure 4-16. Opening Help window Click on the item you want further information for on the window above. -
Page 56: Technical Specifications
Upstream up to 512 Kbps RJ-11 port ADSL telephone line connection Media Interface: RJ-45 port for 10/100BASET Ethernet connection USB port DSL-302T ADSL Modem User’s Guide GENERAL RFC 1661 (PPP) RFC 1994 (CHAP) RFC 1334 (PAP) RFC 2364 (PPP over ATM) - Page 57 DSL-302T ADSL Modem User’s Guide Physical and Environmental Input: 100V ~ 240V AC 50 ~ 60Hz DC Inputs: Power Adapter: Output: 9V AC, 1A Power 3 Watts (max) Consumption: Operating 5° to 40° C (41° - 104° F) Temperature: 5 to 95% (non-condensing)
-
Page 58: Ip Address Setup
IP Address Setup The DSL-302T is designed to provide network administrators maximum flexibility for IP addressing on the Ethernet LAN. The easiest IP setup choice in most cases is to let the Modem do it using DHCP, which is enabled by default. -
Page 59: Using Dhcp
IP addressing on a LAN there are numerous resources freely available on the Internet. There are also many books and chapters of books on the subject of IP address assignment, IP networking and the TCP/IP protocol suite. DSL-302T ADSL Modem User’s Guide Alternative IP Assignment IP Address Subnet Mask 10.0.0.1... -
Page 60: Ip Concepts
DSL-302T ADSL Modem User’s Guide IP Concepts This appendix describes some basic IP concepts, the TCP/IP addressing scheme and show how to assign IP Addresses. When setting up the Modem, you must make sure it has a valid IP address. Even if you will not use the WAN port (ADSL port), you should, at the very least, make sure the Ethernet LAN port is assigned a valid IP address. - Page 61 It is recommended that you choose private network IP Addresses from the above list. For more information on address assignment, refer to RFC 1597, Address Allocation for Private Internets and RFC 1466, Guidelines for Management of IP Address Space. DSL-302T ADSL Modem User’s Guide IP Network Classes Network Addresses (Host Portion in Parenthesis) 1(.0.0.0) to 126(.0.0.0)
-
Page 62: Subnet Mask
The bits of the subnet mask correspond directly to the bits of the IP address. Any bit an a subnet mask that is to correspond to a net ID bit in the IP address must be set to 1. DSL-302T ADSL Modem User’s Guide IP Class... -
Page 63: Microfilters And Splitters
DSL-302T ADSL Modem User’s Guide Microfilters and Splitters Most ADSL clients will be required to install a simple device that prevents the ADSL line from interfering with regular telephone services. These devices are commonly referred to as microfilters or sometimes called (inaccurately) line splitters. -
Page 64: Line Splitter
ADSL – This port connects to the Modem. Phone – This port connects to a telephone or other telephone device. The diagram below illustrates the proper use of the splitter. DSL-302T ADSL Modem User’s Guide ADSL Device Line Splitter Installation... - Page 65 Le Florilege, No. 2, Allée de la Fresnerie, 78330 Fontenay-le-Fleury, France TEL: 33-1-3023-8688 FAX: 33-1-3023-8689 URL: www.dlink-france.fr E-MAIL: info@dlink-france.fr Germany D-Link Central Europe (D-Link Deutschland GmbH) Schwalbacher Strasse 74, D-65760 Eschborn, Germany TEL: 49-6196-77990 FAX: 49-6196-7799300 URL: www.dlink.de BBS: 49-(0) 6192-971199 (analog) BBS: 49-(0) 6192-971198 (ISDN)
- Page 66 Centurion, Gauteng, South Africa TEL: 27-12-665-2165 FAX: 27-12-665-2186 URL: www.d-link.co.za E-MAIL: attie@d-link.co.za Spain D-Link Iberia (Spain and Portugal) Sabino de Arana, 56 bajos, 08028 Barcelona, Spain TEL: 34 93 409 0770 FAX: 34 93 491 0795 URL: www.dlink.es E-MAIL: info@dlink.es...
- Page 67 E-MAIL: Wxavier@dlink-me.com U.K. D-Link Europe (United Kingdom) Ltd Floor, Merit House, Edgware Road, Colindale, London NW9 5AB United Kingdom TEL: 44-020-8731-5555 SALES: 44-020-8731-5550 FAX: 44-020-8731-5511 SALES: 44-020-8731-5551 BBS: 44 (0) 181-235-5511 URL: www.dlink.co.uk E-MAIL: info@dlink.co.uk U.S.A. D-Link U.S.A. 17575 Mt. Herrmann, Fountain Valley, CA 92708 TEL: 1-714-885-6000 FAX: 1-866-743-4905 INFO: 1-800-326-1688 URL: www.dlink.com...
-
Page 68: Registration Card
8. What category best describes your company? oAerospace oEngineering oEducation oFinance oHospital oLegal oInsurance/Real Estate oManufacturing oRetail/Chainstore/Wholesale oGovernment oTransportation/Utilities/Communication oVAR oSystem house/company oOther____________________________________________________________ 9. Would you recommend your D-Link product to a friend? oYes oNo oDon't know yet 10.Your comments on this product? _________________________________________________ __________________________________________________________________________________________...