Related Manuals for Watercool MO-RA IV Series
Summary of Contents for Watercool MO-RA IV Series
-
Page 1: Table Of Contents
MANUAL MO-RA IV Series TABLE OF CONTENTS 1. FAN FRAME 2. FAN MOUNTING 2.1 NOCTUA NF-A20 2.2 140X140X25MM FANS 3. STANDS 4. FAN GRILL 4.1 REMOVING THE STOCK SCREWS 4.2 MOUNTING THE EASYMOUNT PINS 4.3 ATTACH THE FAN GRILL 5. WALL MOUNT 6. - Page 2 GENERAL INFORMATION Please read the instructions carefully before starting the assembly. Failure to follow the instructions or an incorrect assembly can cause permanent damage to your hardware. The assembly is done at your own risk. We recommend demineralized or deionized water (distilled water) with a suitable corrosion inhibitor as coolant.
-
Page 3: Fan Frame
1. FAN FRAME NO TOOLS NEEDED The fan frame can be mounted and unmoun- ted toolless for maintenance. -
Page 4: Fan Mounting 2.1 Noctua Nf-A20
2. FAN MOUNTING 2.1 NOCTUA NF-A20 Required tools Mounting material 4x per Fan Allen Key M4x10 A PERFECT MATCH For mounting the Noctua NF-A20, short M4 10mm screws are required. These have to be used as shown in the following picture. max 8mm... -
Page 5: 140X140X25Mm Fans
2.2 140X140X25MM FANS Required tools Mounting material 4x per Fan Phillips PH1 M3x30 FAN MOUNTING IS EASY For mounting the fans with a standard frame height of 25mm, M3 30mm screws are provided. These have to be used as shown in the following picture. max 8mm... -
Page 6: Stands
3. STANDS Required tools Mounting material Allen Key M4x12 FOR A SAFE STAND The stands are fastened with the enclosed screws as shown below. The washers should be placed between the screw head and the stand. -
Page 7: Fan Grill
4. FAN GRILL 4.1 REMOVING THE STOCK SCREWS Required tools Mounting material Torx TX20 PREPARE THE RADIATOR Start by removing the stock bolts as shown. -
Page 8: Mounting The Easymount Pins
4.2 MOUNTING THE EASYMOUNT PINS EASY MOUNT PINS Then insert the easy-mount-pins into the opening of the washer and screw both together to the radiator. -
Page 9: Attach The Fan Grill
4.3 ATTACH THE FAN GRILL EASY SNAP ON FIT The fan grill can then simply be snapped onto the easy-mount-pins. The locking me- chanism is confirmed by an audible click. To remove the fan grill, simply pull it off. The side opening on the... -
Page 10: Wall Mount
5. WALL MOUNT Required tools Mounting material Allen Key M4x35 WALL MOUNT The wall bracket can be used to attach the radiator to a flat surface. On the radiator side, the moun- ting parts must be fitted as shown. Please ensure that the washer are positioned properly. -
Page 11: Front Logo Led
6. FRONT LOGO LED Required tools Torx TX20 INSERT LED The LED board is inserted in the middle bet- ween the pipe bends and rotated by 90° when the final position is reached. It is fixed in place magnetically. CABLE ROUTING How the cable is routed can be seen in the illustration above. -
Page 12: Ambient Led
7. AMBIENT LED Required tools Torx TX20 LETS BE LIGHT First, the feet must be removed. Then the cable of the LED strip is fed through the hole in the lower part of the housing from the outside. This is then led out at the back as shown and connected to either the MO-RA IV Active Control or the MO-... -
Page 13: Hole Spacing / Bohrungsabstände
8. HOLE SPACING / BOHRUNGSABSTÄNDE MO-RA IV 200 MO-RA IV 200 MO-RA IV 400 MO-RA IV 400... - Page 14 MO-RA IV 600 MO-RA IV 600...
-
Page 15: Dimensions / Abmessungen
9. DIMENSIONS / ABMESSUNGEN MO-RA IV 200 G1/4" MO-RA IV 400 G 1/4"... - Page 16 MO-RA IV 600 G 1/4" KONTAKT CONTACT Watercool GmbH Zum Mevenbruch 6 | 17192 Waren (Müritz) | Germany support@watercool.de Last Update: 07 2024...
Need help?
Do you have a question about the MO-RA IV Series and is the answer not in the manual?
Questions and answers