The direct way to record ................50 Radio menu – overview diagram ..............17 Timer recording with external devices ............51 Other menus – overview diagram ..............17 PhotoViewer ....................52 Operating Loewe equipment .................54 Daily operation ..................18 Select station ....................18 Troubleshooting ..................56 Select video source ..................19 Technical data ..................
Remote control – TV functions Switch on / (page 20) ............. Sound off/on switch off to standby mode ........(page 11) (page 54) ....LED display for current operating mode Switch over to radio mode ......(page 11, 34) (page 10, 54) ........Switch over to TV mode Switch over to operate DVD player ......(page 54) (page 54) ........
Control unit front side of the device Button M: Call the menu Display: in the menu: up/down = Standby On/Off button: = Operation Switch on from the standby mode = Operation without on-screen display Switch off from the standby mode (Radio, EPG data capture or timer recording) Button –...
Connections rear side of the device Factory setting: AV2: DVD recorder You can change this during the Common Interface initial installation (page 11) or in (CI-Slot) the connection wizard (page 40). Headphones Before you connect other devices connection or make any changes, please start S-VHS connection (AVS) the connection wizard (page 40) (e.g.
Welcome Thank you! About this operating manual Loewe sets high standards in technology, design and user friendliness. This For many questions concerning the technology you will find an answer applies equally for TV, video and accessories. in the index of your TV set. If your question concerns TV set operation, you can access a function directly from the index of the Tv set.
Welcome Assist + Operating convenience with wizards You can select the most important operating modes directly with the This TV set offers user prompting with wizards that take you through the Assist + menu (ASSIST button). Selectable modes are: TV, Radio digital, settings step-by-step.
For your safety For your own safety and to prevent unnecessary damage to your device, Power supply read and comply with the following safety instructions: The wrong voltage can damage the set. This equipment must only be connected to a mains power supply which has the same voltage and Proper use and environmental conditions frequency as that specified on the rating plate;...
58). If you want to save even more energy then switch the device Only use original accessories such as Loewe stands if possible (see Ac- off with the mains switch. However note that in this case, EPG (Electronic cessories on page 59).
Adjusting the remote control for operating the TV set Press the TV button. Connections on the back of the set (see also page 5). See page 54 to find out how to operate other Loewe equipment. Replace the cover over the connections.
Initial installation Turning the set on/off First installation wizard Switching the TV set to standby mode Initial installation after switching on for the first time This wizard starts automatically after the set is switched on for the first Activate the mains switch on the back of the set. time, however it can also be called later manually in the TV index, see The display in the control panel on the front of the set Repeat initial installation on page 16.
Page 12
Initial installation Explanations of the setting possibilities, including the upgradeable Logical In various countries, digital stations (DVB-T, DVB-C) are Channel transmitted with a preset channel number per station, satellite reception: Number known as “Logical Channel Numbers“ – “LCN“. In this Energy Decide how energy efficiently you want to operate your case the preset channel numbers are adopted as station...
Initial installation Positioning/aligning the DVB-T antenna Start search Start the automatic station search with OK. The set now searches for TV and DVB radio stations. If you receive one or more DVB-T stations with picture or sound interfer- The stations found in the automatic search are divided into ence, you should change the position and alignment of the antenna.
Operating convenience General information on menu operation The info display Menus for the individual operating modes (TV, radio, teletext, EPG, PIP The info display shows a content-based info text for each menu item at and PhotoViewer) are called with the MENU button. Other menus can the top edge of the screen to aid you in making the settings.
Operating convenience The Assist + menu The index in the TV set You can start all wizards and many operating functions directly from The most important additional functions of the TV set can be called directly by the Assist + menu. this point.
Operating convenience Radio menu – overview diagram Radio menu Sound Stations Timer functions Search wizard Sound via Switch off today only Manual adjustment Switch off daily Sound effects Sound adjustment Change stations One-time reminder Headphone volume Select/change favourites Wake up Mon-Fri Loudness Wake up Sat more...
Daily operation Select station With the station list ➠ In normal TV mode, without other displays, no favour- With the keys P+ and P - on the remote control ites selected: P+/P– Station up/down. OK Call Station list. The station display with sound identification is displayed briefly.
Daily operation Select video source With the favourites lists You can save and call your favourite stations in 6 favourites lists (e.g. for ➠ Please ensure that the appropriate devices have also been registered multiple users). Each favourites list can contain up to 99 stations. After with the connection wizard (see page 40).
Setting the volume the audio component wizard. The Auro selection is only possible if a Loewe DVD Preceiver Auro is connected. V+/V– Volume louder / quieter. The menu item Sound via does not appear if TV speak-...
Daily operation Picture adjustment You can switch between three fixed picture setting variants and the three personal picture values that you have set here. Each of the signal input groups “TV analog”, “TV digital”, “HD analog”, “HD digital”, “PC” and Adjusting the picture “PhotoViewer”...
Daily operation Button functions Selecting the picture format Press the Picture format button until the desired picture Every operating mode of the TV set (TV, radio, teletext, EPG, PIP and Pho- format is set or press toViewer) has its own menu and own functions for the coloured buttons. The function of the coloured buttons is shown at the bottom of the menus and 34 to select the desired picture format.
Page 23
Daily operation Status display Additional selection possibilities for DVB stations In the status display additional selection possibilities can be offered for ➠ In normal TV mode, without other displays. specific programmes depending on the DVB programme provider. END: Show/hide status display. ➠...
Managing stations TV stations Explanations of some search settings, including the upgradeable satellite reception: Various options for managing stations are available via the TV menu. For example the description for TV stations. For radio stations the same applies, Set location Select the country for country-specific defaults and sta- except that the Radio menu is called in Radio mode (see also page 34).
Page 25
Managing stations Search for/update stations – handling of new and no longer found stations Search/update station – manual search After the automatic search/update has been completed, the number of Call TV menu. new found stations is displayed. 34 Select Settings, 6 go to the menu line below.
Page 26
Managing stations Change, delete, move, rename, restore station Rename station ➠ Not possible for MHEG-5 stations. ➠ Change station can also be called via the station list (page 18). ➠ If at least one station is locked the access code must be entered before ➠...
Managing stations Put together / change favourites list Add station to favourites list ➠ All stations (left column) must be selected. Each favourites list can contain up to 99 stations. You can put together If not, change the list with 3. the favourites lists to suit your requirements (e.g.
Picture in Picture Picture in Picture (PIP) Select the PIP picture ➠ The frame is green, The concurrent display of two different images is referred to as Picture if not, press the green button. in Picture. Select the station as usual. ➠...
Picture in Picture Configure Picture in Picture (PIP) mode Change position of the PIP small picture ➠ Other than the status line, which may possibly be In the PIP menu you can set the PIP type (Split screen or Small PIP) and displayed, no other display is shown on the screen: the position of the small picture.
Electronic Programme Guide Electronic Programme Guide – EPG Adjusting the programme list ➠ The selection is at the top of the specifications, EPG stands for Electronic Programme Guide and provides you with if not, press the blue button. on-screen programme details. With the system, as with a printed pro- gramme guide, you can learn about the current programme.
Electronic Programme Guide Calling additional information about the programmes Station In the station selection you can determine for which selection station in the programme guide information is to be dis- ➠ Brief information about many programmes is displayed played. Only stations with are shown in the EPG. below the programme list of the broadcasts.
Teletext Teletext Additional page selection possibilities Your TV set supports the two operating systems TOP Text and FLOF. 1st possibility: Up to 2,000 pages are stored so that you have quick access. Call overview page 100. Starting and ending Teletext 2nd possibility: Switch Teletext on / off.
Teletext Programming timer recordings via Teletext Explanations of the Teletext menu functions: ➠ Teletext is started, Recording A wizard for recording via teletext helps to programme an if not, press the TEXT button. wizard external recorder, see also left column. Call the programme pages of the current station.
Radio Radio mode Switching the screen on/off Red button: Switch off the screen. You can only receive radio stations via DVB. If you do not have DVB radio reception then you can play audio from an The LED display on the set changes from green to orange. external device via the TV set using the audio/AV inputs.
The CA module and the Smart Card are not part of the TV set's scope of Call TV menu. delivery. They are usually available from your dealer. Loewe provides no guarantee for the functioning of the CA module. 34 Select Settings, 6 go to the menu line below.
Software update Software update wizard The software update can be made via a USB stick or DVB antenna. If you do not make any changes, your TV makes it with the following settings: Update source USB and satellite: ASTRA1 19,2°E (DVB-S) TV base software and DVB software (ASTRA1 19,2°E) Frequency...
Page 37
If you have adapted the update settings: A bar informs you about the progress of the charging process. Do not switch your set off during this time! OK proceed. This process can take up to 20 minutes depending on the 3 4 Select Start update, selected update source.
Other settings Parental lock Timer functions You can select and set various security options to prevent unauthorised This menu offers you convenient alarm services. Programmed alarms are use of the TV set and to protect your children from unsuitable pro- also active when the TV set has been switched off to standby.
Other settings On-screen displays Time and date You can select different settings in this menu which affect the on-screen If you receive a station with teletext after switching on the TV, the time displays. and date are recorded automatically. The date may have to be entered manually for some stations.
Operating additional equipment Connection wizard Select the equipment you want to connect or remove equipment you no longer use in the AV equipment The connection wizard serves to connect accessory equipment optimally selection. to the TV set, make changes to the wiring of the devices or remove mo- ...
Page 41
Operating additional equipment Signal type Digital Link Connection wizard New devices/modifications Plus Transfer of the station list to the Digital Link Plus recorder(s). Signal type at socket AV1 (DVD) Automatic CVBS/YC Transfer (per recorder): 100% CVBS Proceed 6 Select the signal types of the individual devices one after another where necessary.
Operating additional equipment Devices to the connections AV1/AV2/AVS Connecting a DVD player to the TV set ➠ DVD player is registered with the connection wizard. Accessory equipment such as DVD players, video and DVD recorders etc. can be connected to the TV set at the Euro-AV sockets AV1 and AV2 Switch off all equipment before connecting.
Page 43
Operating additional equipment Connecting a DVD recorder to the TV set Connecting Camcorder/camera ➠ DVD recorder is registered with the connection wizard. ➠ Camcorder/camera is registered with the connection wizard. Switch off all equipment before connecting. Switch off all equipment before connecting. Connect the Euro-AV output of the DVD recorder to the AV2 socket of the TV set.
Your TV set shows 24p films (see glossary on page 61) which are output With Digital Link HD-capable devices the device by a player connected via HDMI, e.g. Loewe BluTech Vision, automatically name may possibly appear in place of the connection in the original 24p format.
Operating additional equipment Devices to the PC IN connection Playback from the device You can connect a PC to the PC IN socket for example and thus use the Call AV selection. TV screen as a monitor. ➠ When connecting a PC or accessory equipment to the PC IN socket AV selection of the TV set, set one of the following screen resolutions on the PC / COMP.
Operating additional equipment Devices to the Component IN connection Playback from the device Call AV selection. DVD players/recorders or a Set-Top-Box with Component Video connec- tions can also be connected to the Cb/Pb Cr/Pr Y sockets (SD/HD-COMPO- NENT) of the TV set instead of to the EURO-AV sockets. AV selection The connecting cable with three cinch plugs each transfers the picture COMP.
The sound components wizard is preset to playback via TV speakers at the factory. Call TV menu. If a Loewe Preceiver Auro with link cable has been connected to the 34 S elect Connections, TV set, you can only select between TV speakers and Auro in the sound 6 go to the menu line below.
Operating additional equipment Connecting audio amplifiers Connecting digital audio amplifiers Continuation of the left column above ... The sound component wizard permits configuration of different audio amplifiers (stereo amplifiers, surround amplifiers, analogue or digital) with For digital audio transmission: Select yes. different digital audio formats (Dolby Digital, dts, MPEG, and stereo/PCM).
Dolby Digital decoder in the TV set, via an externally connected digital IN is assigned in the connection wizard (see page 41). audio amplifier, Loewe Individual Sound Projector or Loewe Auro. ➠ An external audio amplifier or Loewe Individual Sound...
Operating additional equipment The direct way to record Enter timer data Timer data are displayed after selecting the broadcast you You can programme timer recordings for connected recorders on the TV want to record. You can change these before confirming. set.
If the programmed timer cannot be transmitted to the external recorder Via EPG Via teletext Manual (no Digital Link Plus) but supports Digital Link (Loewe-own system), the 34 S elect Manual, TV receiver is always used. OK call Station selection.
Operating additional equipment PhotoViewer Viewing photos ➠ The photo overview is displayed. You can view photos in the standard JPEG format stored on a USB stick or a memory card in a card reader. You can also collect photos in a slide show. Folder_1 Connecting ➠...
Page 53
Operating additional equipment Open folder Calling the PhotoViewer menu ➠ Folders will only be displayed if they were created on the In the PhotoViewer menu you can make picture settings and select the memory card / USB stick. memory medium. 634Mark a folder in the photo overview.
Setting the remote control to other Loewe devices The specified button combination must be kept pressed (for approx. 5 s) until one of the LEDs flashes twice.
Page 55
Operating additional equipment Functions for the Loewe DVD recorder (Centros 1202, 2102 HD, ViewVision DR + ) Functions for the Loewe DVD player (Auro 2216 PS, 8116 DT) Sound off/on TV Sound off/on LED indicator for current operating mode LED indicator for current operating mode...
Wait until the timer recording ends or delete (displayed in grey). the timer recording (page 51). The control functions of the Loewe Recorder a) The Digital Link function is not activated or a) Activate Digital Link in the recorder (see and the Timer are not working or are not not possible in the recorder.
Page 57
Troubleshooting Problem Possible cause Remedy Digital Link Plus does not work. a) EURO-AV cable is not fully wired (pin 10 not a) Replace the EURO-AV cable. wired). b) Some recorders can only adopt stations b) Restore the recorder to the as-delivered during the initial installation of the TV set.
Technical data General data Modus L 32 HD + 100 Modus L 37 HD + 100 Type Article number 68430xxx 68431xxx Dimensions for device without stand (W x H x D) in cm 84.4 x 59.1 x 9.5 99.1 x 67.8 x 9.3 Dimensions for device with stand (W x H x D) in cm 84.4 x 61.4 x 26.0 99.1 x 70.2 x 26.0...
Upgrade kit Audio AC3 / dts (Art.No. 89781.080): A fully fledged Dolby Digital decoder can be integrated in the TV set with the Audio AC3 upgrade kit. A surround system such as Loewe Individual Sound can then be connected. Adapter and cables: AUDIO LINK adapter 1.5 m...
Accessories Upgrade kits Modus L 32 HD + 100 Modus L 37 HD + 100 TV type Single DVB-T/C USB port Single DVB-S2 Art.No. 89565.081 Audio AC3 / dts Art.No. 89781.080 ex factory available as an upgrade kit ...
This is optimal for sports broad- from Loewe) via the Euro AV sockets of the Loewe TV set with concealed casts but for quieter movies it distorts the picture quality. Loewe TV sets setup.
Page 62
ProScan/Progressive Scan: Progressive Scan (abbr. PS) or full picture L-Link: Intelligent system connection between Loewe devices for the method is a technique in the picture build-up of monitors, TV sets, automatic exchange of information. Makes the operation of TV and beamers, and other display devices in which the output device is not Loewe system components even more convenient.
Page 63
Glossary RGB: Colour signals red, green and blue. Terrestrial: In data transmission a wireless transmission that does not use satellites as intermediate station is referred to as terrestrial. TFT: Thin Film Transistor. One widely distributed application is control of liquid crystal flat screens, for which a signal transistor is used for each Satellite tuner: Receiver for satellite programmes.
Need help?
Do you have a question about the L 37 HD+ 100 and is the answer not in the manual?
Questions and answers