Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Lionel TrainMaster Snowplow
Summary of Contents for Lionel TrainMaster Snowplow
- Page 1 71-8458-250 9/00 Lionel Snowplow Owner’s Manual featuring...
-
Page 2: Table Of Contents
Pullmor ® motor owner of the Lionel Command-equipped under its hood, the Lionel snowplow is ready snowplow locomotive. From the crisp detail for duty on your model railroad. Experience on the outside to the advanced technology the superiority of today’s Lionel. -
Page 3: Transformer Operations
Move ‘em out! • Get your snowplow moving. Press the DIR button on your CAB-1 remote or Lionel transformer. This sequences the Lionel Command reverse unit (LCRU) to the next operating state. The LCRU alternates between three states: forward, neu- tral, and reverse. -
Page 4: Using Your Snowplow's Electrocoupler
ElectroCoupler. When in the non- field generated by a Lionel remote-control Command environment, you must first cou- track section (available separately). Place ple a piece of rolling stock equipped with your rolling stock’s coupler “trigger disc”... -
Page 5: The Command Control Environment
• Make sure your Lionel Command Base is ON and its communications wire is connected to the COMMON post on your Lionel transformer or the U post on any of your installed PowerMasters. • Once positioned on the track, increase track voltage to FULL (on PowerMaster, slide the CMD/CONV switch to CMD). -
Page 6: Cab-1 Commands For Your Snowplow
Transformer operations Running your steam locomotive in the TrainMaster Command environment our Command-equipped snowplow address Engine #1 Example comes factory-programmed with an ID# of “1.” To get your snowplow in PowerMasters set to CMD or traditional action, set PowerMaster to CMD or set power supplies ON FULL all power supplies on full. -
Page 7: Tuning Your Snowplow's Performance
Transformer operations Tuning your snowplow’s performance MOMENTUM tive moving, then press SET; the snowplow Simulate the labored performance of a loco- will stop. The headlight will flash, indicat- motive pulling a heavy load with momentum. ing it’s in the SET mode. Turn the throttle clockwise to get the engine moving, then Press L, M, or H (located under CAB-1’s removable panel) for light, medium, or heavy... - Page 8 TrainMaster Command operations Assigning your locomotive a new ID# s your fleet of Command-equipped Assign a new I D# to your Example Lionels grows, give your snowplow its Command-equipped locomotive own ID#. Choose from any between 1 and 99. Slide the locomotive’s reverse unit Set the locomotive reverse unit control control switch to PROGRAM.
-
Page 9: Maintaining And Servicing Your Snowplow
Maintaining and servicing your snowplow Lubricating your snowplow elp your Lionel snowplow lead a long avoid getting grease or oil on the snowplow’s and productive life on your railroad by wheels, contact rollers, or your track. maintaining it properly. You’ll know your snowplow requires lubri-... -
Page 10: Lubricating Your Snowplow's Pullmor Motor Armature
Finish the job by reinstalling the body screw shown below and apply a small shell and reinserting the cab mounting amount of Lionel oil (two drops) in the screws. armature shaft hole. Reinstall the set screw. Note: Due to gearing, you will not be able to... -
Page 11: Replacing Your Snowplow's Lamps
9 for location). nector goes to the front bulb.) Carefully lift the shell away from the frame. Replace the lens assembly with Lionel part Take care with the various wiring assemblies no. 610-8583-100, available from your connected to the shell. - Page 12 Station, together with proof of original purchase Please make sure you have followed all of the will, at the option of Lionel L.L.C., be repaired or above instructions carefully before returning any replaced, without charge for parts or labor. In the merchandise for service.
Need help?
Do you have a question about the TrainMaster Snowplow and is the answer not in the manual?
Questions and answers