Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Paragon PRLUG-1012GY
Summary of Contents for Paragon PRLUG-1012GY
- Page 1 Paragon Outdoor Aluminum Louvered Pergola 10'×12' Assembly Instructions Register your pergola at www.paragon-outdoor.com for an extra 1 year of coverage! Paragon Group USA Customer Service Contact Information: 1-877-782-4482 support@paragon-outdoor.com @paragonoutdoorcompany...
- Page 2 Paragon Outdoor Aluminum Louvered Pergola 10'×12' Please read the following instructions completely before you begin assembly. Any errors made during installation are not covered by the product's warranty. If you have any questions during the installation process, please call us at 1-877-782-4482.
- Page 3 3D FOOTING MEASUREMENT 3/25...
-
Page 4: Limited Warranty
Paragon Outdoor will replace any defective part within the warranty period, at its discretion, if it is found to be defective of workmanship or materials. Paragon Outdoor may request photographs, videos, or physical return of the defective part for verification purposes. -
Page 5: Planning Assembly
1. In case of a defective part or if a problem occurs while using this product, please contact Paragon Outdoor Customer Service at (877) 782-4482. 2. To order replacement parts, identify the model number and the part number found in your assembly manual. -
Page 6: Safety Information
If you are experiencing any issues with the assembly of your new structure, please do not return – our expert customer service team will help you with all questions for a smooth assembly process. Email: support@paragon-outdoor.com Need Assistance? Call: +1 (877) 782-4482 Hours of Operation Speak with an Expert Customer Service Agent: Monday –... - Page 7 CARTON 1/4(POSTS AND LOOSE PARTS) Reference Parts Quantity Post Reference Parts Quantity Reference Parts Quantity 10×80 Post skirt Expansion bolt 6×35 Base plate Socket screw 6X35 Reference Parts Quantity Reference Parts Quantity 4mm Allen key 6mm Hex bit 10mm 10mm Flat wrench 4mm Hex bit 6mm Allen key PH2 Hex bit...
- Page 8 Reference Parts Quantity Reference Parts Quantity Spin for louver Rubber clog Locking cap Beam fixing screw Plug Gearbox Washer Box cover 6×35 Plastic cap Socket screw 6X35 6×45 Cylinder Socket screw 6X45 Plastic cap Connecting Bar(FO) & Brush Inside! CARTON 3/4(LOUVERS ) Reference Parts Quantity...
-
Page 9: Assembly Guidelines
CARTON 4/4(LOUVERS ) Reference Parts Quantity Louver Reference Parts Quantity Reference Parts Quantity 4×16 Louver end cap B Screw 4x16 ASSEMBLY GUIDELINES STEP 1 : Assembly of Louvers STEP 2 : Building the frame STEP 3 :Louvers and their connections 9/25... - Page 10 STEP 1 Assembly of Louvers Components Parts Tools 10mm 4×16 6×35 Attention: 1. Master louver P will be assembled with louver end cap P5/P3-qty 1 This master louver will attach to gear box (Q8) in later step. 2. Louvers P will be assembled with louver end caps P5/P4-qty 22 10/25...
- Page 11 STEP 1-1 Attention: Do not overtighten. Q19 Screw. It should not extend past Q16. Assemble the louver end caps Q4 and Q5 as shown below. P4x22 P5x22 11/25...
- Page 12 STEP 1-2 Attention: P master louver with louver end caps P3/P5 will control the gear box (Q8) that opens and closes the louvers. Attaching P3 (master louver end cap) / P5(louver end cap) to P (master louver). Use qty 2 parts of P14/Q18, once attached, place Q13(rubber clog) in each hole at ends of louvers near louver end caps.
- Page 13 13/25...
- Page 14 STEP 2 Building the Frame Components Parts Tools 6×35 Attention: 1. Assemble Posts first. 2. Remove D from Beam B and B1. It will be installed at a later step. 14/25...
- Page 15 STEP 2-1 1. Slide Q1 (post skirt) onto A (post). Make sure to align notch on Q1 with A, as this is a drain outlet. 2. Use Q20(socket screw 6x35) to install Q2(base plate) to 3. Tighten the screw with Z3 if needed. attach A (post).
- Page 16 STEP 2-3 1. Place the A (post) and C (side beam) on a flat surface.Use a square to make sure Beam C/Post A are properly aligned before tightening. Attach C (side beam) to A (Post) 2. Use Q7 ( Beam fixing screw ) and insert into C (side Beam) to connect C to A, tighten with Z6 (6mm bit) .
- Page 17 STEP 2-4 1. Insert Beams B/B1 into A (post) aligning holes. Use a square to make sure Beam B/ B1 to Post A are properly aligned before tightening. (beam) attaching it to A 2. Insert Q7 (beam fixing screw ) into B&B1 (post).
-
Page 18: Step 3 Installing Louvers
STEP 3 Installing Louvers Components Parts Tools 10×80 6×45 Attention: Please follow the order outlined in the instruction manual when assembling louvers. 18/25... - Page 19 STEP 3-1 1. Put P (Master louver) with P5/P3 louver end caps into B (beam). This is placed in 2nd hole for louver placement, where Beam B has opening for Q8 gear box. Q8 will install in later step. Attention: Insert completely P (master louver) with louver end cap P3 into notch of Beam B first.
- Page 20 STEP 3-2 Attention: Keep same procedure as STEP 3-1 Place all P (louvers) on beam as same procedure as STEP 3-1 STEP 3-3 After louvers are installed, lay them in the closed position and insert into the opening above spin (Q6) on louver end cap. 20/25...
- Page 21 STEP 3-4 Attention: Louvers should be vertical 1. Place Q11(cylinder) on P3 (master louver end cap) 2. Remove Q9 (box cover), place Q9/Q8 onto Q11 and secure with Q21 screws. Install H into Q8 and tighten. 21/25...
- Page 22 STEP 3-5 Attention: Keep all louvers vertical for easy assembly of F (connector bar). 1. Lock F (connector bar) on louver end caps 2. Place washer Q18 onto screw of louver end cap then insert Q17 into screw of louver end cap. Repeat this with all louver end caps to connect F to each louver G.
- Page 23 STEP 3-6 Attention: Place D (cap beam) onto Beam B and B1. Gently tap into place to connect. STEP 3-7 Attention: Keep all louvers as vertical. Cover holes in each corner on Beams C/B/B1 with Q10 (plastic cap). 23/25...
- Page 24 STEP 3-8 Attention: Make sure the unit is "square" before anchoring. Check size 12MM Check all dimensions of the pergola, then anchor base plate Q2 to concrete foundation using Q15 (expansion bolt). Caution the post skirting can scratch post. 24/25...
- Page 25 Paragon Group USA Customer Service Contact Information: 1-877-782-4482 support@paragon-outdoor.com @paragonoutdoorcompany...
Need help?
Do you have a question about the PRLUG-1012GY and is the answer not in the manual?
Questions and answers