Diagrams; Circuit Boards Location - Sony HCD-MDX10 - Compact Disk Deck Receiver Component Service Manual

CD SECTION
Note:
1. CD Block is basically constructed to operate without adjustment.
Therefore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10M impedance.
4. Clean the object lens by an applicator with neutral detergent when
the signal level is low than specified value with the following
checks.
S Curve Check
oscilloscope
BD board
TP (FE)
+
TP (VC)
–
Procedure :
1. Connect the oscilloscope to test points TP (FE) and TP (VC).
2. Connect TP (FEI) and GND, and TP (AGCCON) and GND of
the BD board with lead wires.
3. Press the 1/u button to turn the set ON.
4. With the disc (YEDS-18) loaded, press the ^ button and
perform focus search. (Focus search will be performed in the
same way even while the disc table is pushed in and out.)
5. Check the symmetry and peak to peak level of the oscilloscope
waveform (S curve) at this time.
S-curve waveform
symmetry
A
Within 4 1 Vp-p
B
6. After check, remove the lead wire connected in step 2.
Note: • Try to measure several times to make sure than the ratio of
A : B or B : A is more than 10 : 7.
• Take sweep time as long as possible and light up the bright-
ness to obtain best waveform.
Adjustment Location : BD (CD) board
RF Level Check
oscilloscope
BD board
+
TP (RF)
TP (VC) –
Procedure :
1. Connect oscilloscope to test point TP (RF) and TP (VC) on BD
board.
2. Connect TP (AGCCON) and GND of the BD board with lead
wires.
3. Press the 1/u button to turn the set ON.
4. Put disc (YEDS-18) in and playback 5track.
5. Confirm that oscilloscope waveform is clear and check RF sig-
nal level is correct or not.
6. After check, remove the lead wire connected in step 2.
Note: Clear RF signal waveform means that the shape " " can be
clearly distinguished at the center of the waveform.
RF signal waveform
VOLT/DIV : 200mV
TIME/DIV : 500ns
level : 1.45 0.3 Vp-p
Adjustment Location : BD (CD) board
E-F Balance (1 Track Jump) check
oscilloscope
BD board
TP (TE) +
TP (VC) –
Procedure:
1. Connect oscilloscope to test point TP (TE) on BD board.
2. Press the 1/u button to turn the unit ON.
3. Put disc (YEDS-18) in to play the number five track.
4. Press the ^ button.
5. Check the level B of the oscilloscope's waveform and the A (DC
voltage) of the center of the Traverse waveform.
Confirm the following:
• A/B x 100 = less then ± 22 (%)
• B = 1.3 ± 0.6 Vp-p
1 track jump waveform
Center of the waveform
B
0V
Symmetry
level : 1.3 0.6 Vp-p
Adjustment Location : BD (CD) board
Adjustment Location :
[ BD (CD) BOARD ] — SIDE A —
TP
(VC)
TP
(RF)
TP
(AGCCON)
TP (FE)
TP
TP
(TE)
(FE1)
– 39 –

8-1. CIRCUIT BOARDS LOCATION

DISPLAY board
JOG board
A (DC voitage)
SENSOR board
POWER SW board
CD PANEL board
LEAF SW board
AUDIO board
SECTION 8

DIAGRAMS

STANDBY board MD LINK board
MD DIGITAL board
ENCAPSULATED COMPONENT
(US,CND,AR,KR,SP,MY,HK,AUS)
TUNER unit
(AEP,UK,E,G,CIS)
SECONDARY board
VOL board
MAIN board
ENCAPSULATED COMPONENT/TUNER
unit is supplied as the assembled block.
MOTOR (TURN) board
CONNECTOR board
SW board
BD (CD) board
BD (MD) board
MOTOR (SLIDE) board
MD LINK SW board
– 40 –
HCD-MDX10
• Abbreviation
CND : Canadian model
G : German model
SP : Singapore model
MY : Malaysia model
HK : Hong Kong model
AR : Argentine model
KR : Korea model
AUS : Australian model