Parts And Functions; Indoor Unit; Remote Controller; Display Board - Haier HSU-12LEA13-M Operation Manual

Parts and Functions

Indoor Unit

1
2
3
7
5
Inlet
1 1
Inlet grille
2 2
Air Purifying Filter (inside)
3 3
Outlet
5 4
Actual inlet grille may vary from the one shown in the
manual according to the product purchased

Display board

8
2 3
1
Signal receiver hole
1
COOL display
2
HEAT display
3
Ambient temp.display
4
When receiving the remote control signal,
display the set temperature and in the rest
time the room temperature is displayed and
this room temperature is only for reference.

Outdoor Unit

OUTLET
INLET 1 4

Clock set

Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press
or decrease 1min. If the button is kept pressed,time will
change quickly. After time setting is confirmed,press SET,
"AM "and "PM" stop flashing,while clock starts working.
TIMER
CLOCK
SET
SLEEP
LOCK RESET
1
Horizontal flap
5 4
(adjust up and down air flow
Don't adjust it manually)
Vertical blade
6 6
(adjust left and right air flow)
Anion generator
7
4 5 6
HEALTH display
5
(If the unit which you purchased
has healthy function,follow it.
If not,please ignore.)
6 Dry display
TIMER OFF display
7
TIMER ON display
SLEEP display
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
will increase

Remote controller

1
2
5
3
23
23
13
4 5
18
6
8
12
21
19
17
(inside)
7
1. Operation mode display
ation mode AUT O
Ope
r
Remote controller
Display board
2. SWING display
3.FAN SPEED display
NOTE:
Cooling only unit do not have displays and functions related with heating
If the unit which you purchased has healthy function,follow it.If not,please ignore.

Loading of the battery

4
Load the battery,then put on the cover again.
Note:
The distance between the signal transmission head and the
receiver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change-over
wireless telephone is installed in the type fluorescent lamp or
room, the receiver is apt to be disturbed in receivingthe signals,
so the distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the
ries have been used up. Please change batteries.
batte
If the remote controller can't run normally during operation,
please remove the batteries and
Hint:
Remove the batteries in case unit won't be in usage for a long period.
If there are any display after taking-out, just need to press reset key
4. SLEEP display
10
5. LOCK display
6
6. SIGNAL SENDING
7
7.TIMER OFF display
8
8. TIMER ON display
9. CLOCK display
9
10. TEMP display
4
HEALTH ON/OFF
11. POWER ON/OFF
11 12. MODE
FAN
13. FAN
MODE
15
SWING 14. HOUR
20
TIMER
15. SWING
14
CLOCK
16. SLEEP
16
SET SLEEP
22 17. LOCK
LOCK
RESET
18. TEMP.SETTING
19. SET
20. TIMER
21. CLOCK
22. RESET
COOLDRY HEAT FAN
23. HEALTH
AUTO LO MED HI
1
Remove the battery cover;
2
2
Load the batteries as
illustrated. 2 R-03 batteries,
1
resetting key(cylinder);
3
Be sure that the loading
3
is in line with the " + "/"-";
reload several minutes later.
Used for unit start and stop.
Used to select AUTO run,
COOL,DRY,HEAT and
FAN operation
Used to select fan speed
LO, MED, HI, AUTO
Used to set clock and timer
setting.
Used to set auto fan direction.
Used to select sleep mode.
Used to lock buttons and
LCD display.
Used to select your desired
temp.
Used to confirm timer and
clock settings.
Used to select TIMER ON,
TIMER OFF,TIMER ON-OFF
Used to set correct time
Used to reset the controller
back to normal condition.
Used to operate the healthy
u f . n t c o i n