Safety Precautions (Read these precautions before using.) Before installation, operation, maintenance or inspection of this product, thoroughly read through and understand this manual and the associated manuals. Also, take care to handle the module properly and safely. This manual classifies the safety precautions into two categories: Indicates that incorrect handling may cause hazardous conditions, resulting in death or severe injury.
Page 4
Failure to do so may cause electric shock or damage to the product. Use the product within the generic environment specifications described in LE-10WTA-CCL LD-10WTB-CCL APPLICATION MANUAL JZ990D56901. Never use the product in areas with excessive dust, oily smoke, conductive dusts, corrosive gas (salt air, Cl...
Page 5
Safety Precautions (Read these precautions before using.) Connect the DC power supply wiring to the dedicated terminals. If an AC power supply is connected to a DC input terminal or DC power supply terminal, the tension controller will burn out. ...
Page 6
Do not disassemble or modify the tension controller. Doing so may cause fire, equipment failures, or malfunctions. * For repair, contact your local Mitsubishi Electric distributor. Turn off the power to the tension controller before connecting or disconnecting any extension cable.
Page 7
• Since the examples indicated by this manual, technical bulletin, catalog, etc. are used as a reference, please use it after confirming the function and safety of the equipment and system. Mitsubishi Electric will accept no responsibility for actual use of the product based on these illustrative examples.
Page 9
Excel for the tension controller by using sample data for MX Sheet. Read this manual and manuals of related products before using the LE-10WTA-CCL/LD-10WTB-CCL, understand sufficiently the specifications of all products, and use them properly. See to it that this instruction manual is delivered to the end user.
Introduction Thank you very much for purchasing the tension controller LE-10WTA-CCL/LD-10WTB-CCL. Thoroughly read this manual before using the LE-10WTA-CCL/LD-10WTB-CCL, understand sufficiently its functions and performance, and use it properly. Table of Contents Safety Precautions ......................1 Introduction........................9 Table of Contents ......................9 Associated Manuals and How to Obtain Manuals ............10...
How to set and operate each utility with MX MX Component Version 3 Operating Manual SH-080271 Component How to obtain manuals For product manuals or documents, consult with the Mitsubishi Electric dealer from who you purchased your product. Associated Manuals and How to Obtain Manuals...
This manual explains how to read the tension and read/write the set value from/to Microsoft Excel the tension controller LE-10WTA-CCL/LD-10WTB-CCL by using sample data for MX Sheet. Refer to each software manual for the installation procedure of the required software.
USB cable for connecting personal computer port MR-J3USBCBL3M[3m], GT09-C30USB-5P[3m] Sample Data for MX Sheet and USB Driver For sample data for MX Sheet and USB driver, consult with the Mitsubishi Electric dealer from whom you purchased your product. 1. Outline...
Installation of USB Driver 1.5.1 USB driver installation Install the USB driver software. POINT POINT POINT • Please confirm whether the driver was installed normally after it is installed. Refer to the following for confirmation. Subsection 1.5.2 Driver installation confirmation •...
Page 16
Install the driver. ® Windows Please install the driver using the following procedure. (1) When the USB cable is connected to the personal computer, the following screen is displayed. Select "Install from a list or specific location[Advanced]" and click [ Next> ]. Then, specify the path "extraction destination folder name\folder of the downloaded file\WinVista_XP"...
Page 17
(4) The following screen is displayed. Select "Install from a list or specific location[Advanced]" and click [ Next> ]. Then, specify the path "extraction destination folder name\folder of the downloaded file\WinVista_XP" to install the driver. The installation of the USB Serial Port software will begin. ®...
Page 18
® Windows Vista Please install the driver using the following procedure. ® The installation procedure is explained for when connecting a personal computer with Windows to the LM-10WA-USB. (1) When the USB cable is connected to the personal computer, the following screen is displayed. Click [ Located and install driver software (recommended) ].
Page 19
(4) The following screen is displayed. Select [ I don't have the disc. Show me other options. ] to begin installation of the USB driver. (5) The following screen is displayed. Click [ Install this driver software anyway ]. 1. Outline...
Page 20
(6) The following screen is displayed. Click [ Close ]. (7) The following screen is displayed. (The following screen may be displayed when connected to a Network.) Click [ Don't search online ]. 1. Outline...
Page 21
(8) The following screen is displayed. Click [ I don't have the disc. Show me other options. ]. The installation of the USB Serial Port software will begin. (9) The same screen from step (5) is displayed. Click [ Install this driver software anyway ]. (10) The following screen is displayed.
Page 22
® Windows ® The USB drivers of Ver.1.10 or later version are compatible with Windows 7 64bit. Please install the driver using the following procedure. The installation procedure is explained for when connecting a personal computer with ® Windows 7 to the LM-10WA-USB.
Page 23
(3) The following screen is displayed. Select [ Driver ] tab. (4) The following screen is displayed. Click [ Update Driver... ]. 1. Outline...
Page 24
(5) The following screen is displayed. Click [ Browse my computer for driver software ]. (6) Since the following screen is displayed, the location of the driver is specified. Click [ Next ]. Add check mark. 1. Outline...
Page 25
(7) The following screen is displayed. Click [ Install this driver software anyway ]. (8) The installation of the USB driver software is completed, and the following screen is displayed. Click [ Close ]. (9) The message "Device driver software was not successfully installed" appears again. Clicking [ Click here for details.
Page 26
(10) Install the USB Serial Port from Device Manager. -----------*1 Put the cursor on [ USB Serial Port ] in [ Other devices ], double-click or right-click it, and select [ Properties ]. Or put the cursor on [ USB Serial Port ], right-click it, and select [ Update Driver Software... ] to skip steps (11) and (12) and jump to step (13).
Page 27
(12) The following screen is displayed. Click [ Update Driver... ]. (13) The following screen is displayed. Click [ Browse my computer for driver software ]. 1. Outline...
Page 28
(14) The following screen is displayed, specify the location of the driver. Add check mark. (15) The following screen is displayed. Click [ Install this driver software anyway ]. 1. Outline...
Page 29
(16) Click [ Close ]. Installation of the USB Serial Port software will finish. Next, please confirm whether the driver was installed normally. Refer to the following for confirmation. The following screen is displayed. Subsection 1.5.2 Driver installation confirmation 1. Outline...
1.5.2 Driver installation confirmation Procedure for confirming installation of the driver is described below. Please perform the following procedure while the LM-10WA-USB is connected to the personal computer. ® Windows XP example follows. ® XP, click [ Start ] [ Control Panel ] [ Performance and Maintenance ] [ System ] •...
Identification result: • If (1) through (3) are all confirmed, installation is normal. Select the programming software COM number as the COM number currently assigned on the screen above. • If any one of (1) through (3) is not satisfied, installation is not normal. (Possibly, the installation procedure was canceled during processing or the USB Serial Port software is not installed.) In this case, please start the installation procedure again from the beginning, after uninstalling the driver.
Page 32
(3) The following screen is displayed. Click [ Finish ]. When the driver is not installed normally Confirm whether the same thing is displayed as that on the screen in step (1) from the procedure described in "When the driver is installed normally". When "LM-10WA-USB Drivers(V*.**)"...
Page 33
® Windows Vista Please uninstall the driver using the following procedure. Caution Driver software must be uninstalled starting with "Ports (COM & LPT)" after which the "Universal Serial Bus Controllers" should be uninstalled. If the "Universal Serial Bus Controllers" are uninstalled first, the driver software for the FX-USB-AW/ -USB-BD will not be uninstalled correctly.
Page 34
(2) The following screen is displayed. Select [ Driver ] tab. (3) The following screen is displayed. Click [ Uninstall ]. 1. Outline...
Page 35
(4) The following screen is displayed. Add a check mark to [ Delete the driver software for this device ], and click [ OK ]. The USB Serial Port software is uninstalled. Afterward, uninstall the USB driver following steps (5) to (8). Add check mark.
Page 36
(6) The following screen is displayed. Select [ Driver ] tab. (7) The following screen is displayed. Click [ Uninstall ]. 1. Outline...
Page 37
(8) The following screen is displayed. Add a check mark to [ Delete the driver software for this device ], and click [ OK ]. The USB driver is uninstalled. Add check mark. 1. Outline...
Page 38
® Windows Please uninstall the driver using the following procedure. Caution Driver software must be uninstalled starting with "Ports (COM & LPT)" after which the "Universal Serial Bus Controllers" should be uninstalled. If the "Universal Serial Bus Controllers" are uninstalled first, the driver software for the LM-10WA-USB will not be uninstalled correctly.
Page 39
(2) The following screen is displayed. Select [ Driver ] tab. (3) The following screen is displayed. Click [ Uninstall ]. 1. Outline...
Page 40
(4) The following screen is displayed. Add a check mark to [ Delete the driver software for this device. ], and click [ OK ]. The USB Serial Port software is uninstalled. Afterward, uninstall the USB driver following steps (5) to (8). Add check mark.
Page 41
(6) The following screen is displayed. Select [ Driver ] tab. (7) The following screen is displayed. Click [ Uninstall ]. 1. Outline...
Page 42
(8) The following screen is displayed. Add a check mark to [ Delete the driver software for this device. ], and click [ OK ]. The USB driver is uninstalled. Add check mark. 1. Outline...
Read and Write Using Sample Data This chapter explains how to read/write from/to the tension controller by using sample data. Communication Setting This section explains the prodecure for communication setting. (1) Open the [ Communication Setup Utility ] dialog box with the following operation from the start ®...
Page 44
(4) The [ Communication Setting Wizard - PC side ] dialog box is displayed. Set the items as shown in the table below and click the [ Next> ] button. Set these items. Setting Setting contents PC side I/F Serial Select the port where the USB driver is installed.
Page 45
(6) The [ Communication Setting Wizard - Network ] dialog box is displayed. Set [ Station type ] to "Host station" and click the [ Next> ] button. Set these items. (7) The [ Communication Setting Wizard - Finished ] dialog box is displayed. Complete the setting with the [ Finish ] button.
Communication Test (1) Open the [ Communication Setup Utility ] dialog box with the following operation from the start ® menu of Windows [ Start ] - [ All Programs ] - [ MELSOFT Application ] - [ MX Component ] - [ Communication Setup Utility ] (2) The [ Target setting ] page of the [ Communication Setup Utility ] dialog box is displayed.
Page 47
(4) The result of the communication test is displayed. Press the [ OK ] button. Refer to the following manual when the test result is not acceptable. MX Component Version3 Programming Manual (SH080272) (Acceptable) (Not acceptable) (5) The [ Target setting ] page of the [ Communication Setup Utility ] dialog box is displayed. Exit the dialog box with the [ Exit ] button.
Sample Data for MX Sheet Start up the sample data for MX Sheet by double-clicking on it. Refer to the following manual for details on MX Sheet. MX Sheet Version 1 Operating Manual(Introduction)(SH-080347E) 13 14 15 Item Revision Device No. Device No.
REVISIONS Manual Print Date Revision Number Jul. 2013 First Printing The "sample data for MX Sheet" was changed with "sample data Ver. 1.10 for MX Apr. 2014 Sheet". REVISIONS...
Page 62
JZ990D57001B Effective April 2014 (MEE) Specifications are subject to change without notice.
Need help?
Do you have a question about the LE-10WTA-CCL and is the answer not in the manual?
Questions and answers