1. Manuals
  2. Brands
  3. Hiland Manuals
  4. Outdoor Fireplace
  5. GFT-10513
  6. Assembly instructions manual

Hiland GFT-10513 Assembly Instructions Manual

Outdoor gas fire pit
Hide thumbs

Advertisement

Table of Contents

Assembly Instructions
OUTDOOR GAS FIRE PIT
Model# : GFT-10513
Item # : PF19901
R
C
US
Please keep this instruction manual for future reference
Warning:
READ INSTRUCTION MANUAL BEFORE ATTEMPTING TO ASSEMBLE OR
OPERATE THIS PRODUCT.
Keep the screws and parts out of reach of children.
(Made in China)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GFT-10513 and is the answer not in the manual?

Questions and answers

Related Manuals for Hiland GFT-10513

Summary of Contents for Hiland GFT-10513

  • Page 1 Assembly Instructions OUTDOOR GAS FIRE PIT Model# : GFT-10513 Item # : PF19901 Please keep this instruction manual for future reference Warning: READ INSTRUCTION MANUAL BEFORE ATTEMPTING TO ASSEMBLE OR OPERATE THIS PRODUCT. Keep the screws and parts out of reach of children.
  • Page 2 WARNINGS AND CAUTIONS Please read the instruction before use. This appliance must be installed in accordance with regulations as are enforced. WARNING CAUTION Do not try to light this appliance Keep the instruction for future use. without reading the “LIGHTING” instructions section of this manual.

  • Page 3: Table Of Contents

    CONTENTS • Warning and Cautions.................1 ............2 Table Contents......• Warnings..................3-4 • Tools and Parts.................5-7 • Assembly..................8-11 • • Lighting Operation................12-14 • Maintenance and Storage............15-16 Trouble Shooting................17 • REMINDER BEFORE ASSEMBLY Verify that all parts are included with your gas fire pit BEFORE assembly. For your convenience, some parts may be pre-assembled or attached to heater components.

  • Page 4: Warnings

    Warning You must provide propane gas an propane cylinder. Use a standard 20 lb. propane cylinder only. Use this heater only with a propane vapor with draw a supply system. See Chapter 5 of the Standard for Storage and Handling of Liquefied Petroleum Gas, ANSI/NFPA 58. Your local library or fire department should have this book.
  • Page 5 NOTE : PLEASE READ THE FOLLOWING SAFETY RULES. WARNING: Installation and repair should be done by The unit is not for use with solid fuel. a qualified service person. The appliance The installation must confirm with local should be inspected before use and at codes or, in the absence of local codes, least annually by a qualified service with the National Fuel Gas Code, ANSI...
  • Page 7 Parts List DESCRIPTION REFERENCE IMAGE PARTS Cover Lava Rocks Table Top with Burner Side Panel Side Panel with Window Door Panel Back Leg Front Leg (Left) Front Leg (Right) Gas Tank Support Heat Shield Mesh Screen AAA Battery...
  • Page 8 Hardware S TS T REFERENCE IMAGE DESCRIPTION M6 X12 bolt M5 X10 bolt M5 Nut Tools Required (Not included) Adjustable open end wrench Phillips screwdriver...

  • Page 9: Assembly

    Assembly Instructions Step 1: Step 2: Connect all four legs(G,H,I) to the able op with urner(C) by using eight M6 x 12 olts (AA). NOTE: PLACE TABLE TOP TO NON-ABRASIVE SURFACE. PLEASE DON’T TIGHTEN ANY SCREWS TO THE END AT THIS STEP.
  • Page 10 Assembly Instructions Step 4: 12 bolts (AA). Step 5: Step 6： burner is in operation. Wait until the unit cools before replacing the cover.
  • Page 11 Assembly Instructions Step 7: Put the cylinder into the gas tank support (J), and secure the cylinder by tightening the screw in the gas tank support. Keep the hose face to Front leg(H). The propane cylinder is sold separately. Use hose a standard 20 lb.
  • Page 12 Steps to replace the cylinder when the gas runs out: Step 10: Separate the regulator from the cylinder. Step 11: Loosen the screw in the gas tank support. Step 12: Remove the cylinder from the gas tank. Step 13: Replace the new cylinder as Step 6 in assembly part.

  • Page 13: Lighting Operation

    OPERATION WARNING: Never use this appliance for other than the intended use. Do not use this appliance to prepare food. Initial Lighting: When lit for the first time, the appliance emits a slight odor. This is normal temporary condition caused by the “burn –in” of internal paints and lubricants used in the manufacturing process and does not occur again.
  • Page 14 Operating (continued) LEAK TESTING OPERATION WARNING: A leak test must be performed annually or if a part of the gas system is replaced. WARNING: Never use an open flame to check for gas leaks. Be certain no sparks or open flames are in the area while you check for leaks.
  • Page 15 OPERATION Lighting instructions WARNING FOR YOUR SAFETY: Press and hold electronic igniter Keep face and body away from button. burner area when lighting. Ensure burner controls are in the Turn the burner control to the high off position. Slowly turn on the position, press and hold in.

  • Page 16: Maintenance And Storage

    MAINTENANCE AND STORAGE CLEANING AND MAINTENANCE To enjoy years of outstanding performance from your heater , make sure you perform the following maintenance activities on a regular basis: • Keep exterior surface clean. • Use warm soapy water for cleaning. Never use flammable or corrosive cleaning agents.
  • Page 17 MAINTENANCE AND STORAGE STORAGE: Between uses: • Turn the control knob to “OFF” position. • Disconnect LP source. • Store heater upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail, snow, dust and debris). •...

  • Page 18: Trouble Shooting

    TROUBLE OF SHOOTING PROBLEM PROBABLE CAUSE SOLUTION Low heat / Low flame For propane- improper lighting Ensure lighting procedure is followed carefully. The when valve turned to procedure. valve must be in the off position when the tank valve is high.

This manual is also suitable for:

Pf19901

Table of Contents