Related Manuals for Digiever DS-4200 UHD Series
Summary of Contents for Digiever DS-4200 UHD Series
- Page 1 Network Video Recorder Quick Installation Guide DS-4200 UHD Series 2.2.0.8 Information in this document is subject to change without notice. © Copyright 2024, DIGIEVER Corporation. All rights reserved.
-
Page 2: Table Of Contents
Power on and Connecting ................9 Securing the Power Cord ................10 Connection to DIGIEVER NVR ..............12 Quick Configuration ..................15 Appendix......................16 LED Indicators at Front Panel ................16 LED Indicators at Rear Panel ................17... -
Page 3: Safety Notice
Quick Installation Guide Thank you for choosing DIGIEVER Network Video Recorder (NVR). The following quick guide will lead you to complete the installation and configuration of the NVR. Please read the following description carefully. Safety Notice The following safety precautions will increase the life of the NVR. Follow all precautions and instructions. -
Page 4: Pre-Installation Notice
1-4 hard disks Compatibility of hard disk with the NVR 1 slotted screwdriver and 1 Philips screwdriver *For camera compatibility, please check our website http://www.digiever.com/support/compatibility.php System Requirements Remote PC The following are minimum system requirements for a personal computer to operate the NVR in better performance: ... - Page 5 Graphics Adapter AGP or PCI-Express, minimum 1024× 768, 16bit colors, 1G memory or above Note: It is highly recommended to use a graphics adaptor which provides higher than resolutions 1024x768 in order to experience the full benefits of the software. ...
-
Page 6: Package Contents
Package Contents Network Video Recorder Power Cord Power Adapter RJ45 Network Cable Screws for 2.5” HDD Screws for 3.5” HDD Power Code Bracket Product CD... -
Page 7: Hardware Description
Hardware Description Front View Rear View Power LED indicator System LED indicators HDD LED indicator Network LED indicator USB backup button with LED Indicator 1 x USB 3.2 Gen 1x1 port (Support auto video backup) HDD 1 HDD 2 HDD 3 HDD 4 2 x HDMI 2.0a outputs... -
Page 8: Hard Disk Installation
Hard Disk Installation Please follow the steps as illustrated below to install the hard disk: ① Press the button on the lower portion of the hard disk tray to release the latch. ② Using the latch, gently pull the disk tray out of the disk bay. ③... - Page 9 (2) 2.5-inch hard disks and SSD hard disks: Place the hard disk into the area of the disk tray outlined in red (see picture below). Make sure that the mounting holes on the bottom of the hard disk and disk tray are lined up. Secure the drive with four screws. ④...
-
Page 10: Power On And Connecting
Turning the lock clockwise will unlock it. Un-lock: Lock: Note: Disk tray locks can be found on DS-4200 UHD series devices. Power on and Connecting ① Connect the Ethernet cable to the 2.5 Gigabit LAN port Connect the power cord to power connector... -
Page 11: Securing The Power Cord
Turn on the server and there is a beep to indicate the NVR is in booting process. ③ Please wait for minutes until NVR beeps another time. The installation of NVR is complete right now. Securing the Power Cord You can use the provided cord bracket to secure the power cord in place, if you are concerned about the power cord becoming detached when the NVR is moved. - Page 12 ② Attach the bracket to the power cord as shown in the graphic below ③ Remove the fan screw by unscrewing it counter-clockwise ④ Position the bracket over the hole for the removed fan screw. Secure the bracket in place by replacing the fan screw.
-
Page 13: Connection To Digiever Nvr
Connection to DIGIEVER NVR Please insert the product CD-ROM on a PC to install NVR Search. Finally, you can start Quick Configuration on a web page. Install NVR Search for finding NVR in the network ① Connect to the configured NVR, download and install NVR- ②... - Page 14 ② Connect to the NVR Connect to the NVR After setting the NVR Search, user can connect to the monitoring page by the following two options: (1) NVR Search Once you click “Connect” or double click the selected NVR list, the web browser will pop up automatically.
- Page 15 2. Enter a user name and password Log in the NVR with the default administrator account (user name: admin, password: admin). 3. Download and install NVR-Client.exe, a software application, to execute liveview monitoring and video playback.
-
Page 16: Quick Configuration
Quick Configuration After users log in NVR, the system will direct you to set Quick Configuration in 5 steps. Follow the instructions of the Overview of wizard to complete the system setup. Once 5-step Quick Configuration are completed, you can click “Start Live View”... -
Page 17: Appendix
Appendix LED Indicators at Front Panel LED Color & Status Indicate Power Off Blue Power On Power UPS power is from AC power mode to battery mode System is off or in sleep mode when UPS battery is too low Green blinking System goes on or goes off System... -
Page 18: Led Indicators At Rear Panel
LED Indicators at Rear Panel LED Position LED/State Indicate No connection/ 10Mbps connection LAN1 Speed LAN2 (Top LED) Orange 1G /100Mbps connection Green 2.5G connection LAN Link is not established LAN1 Link/Activity Green LAN Link is established LAN2 (Bottom LED) Green LAN activity is occurring blinking...
Need help?
Do you have a question about the DS-4200 UHD Series and is the answer not in the manual?
Questions and answers