Download Print this page
American Lighting HPR68-RGB Installation Instructions

American Lighting HPR68-RGB Installation Instructions

24v dc pool-rated neon strip light

Advertisement

Quick Links

POOL-RATED NEON STRIP LIGHT
24V DC
INSTALLATION INSTRUCTIONS
HPR68-RGB / HPR68-SC / HPR68-SW
These products may represent a possible shock or fire hazard if
improperly installed or attached in any way. Products should be
installed in accordance with these instructions, current electrical
codes, and/or the current National Electric Code (NEC).
Use this fixture with a 24V DC power supply only (sold
separately). Any other power supply may damage the fixture.
To reduce the risk of fire, electric shock or injury to persons, use
this flexible light only with American Lighting/Prizm recommended
drivers, controllers, power connectors, splices and extensions.
SAFETY INFORMATION
• Read all installation instructions before beginning; if not qualified, do not attempt installation. Contact a qualified electrician.
• To reduce the risk of fire, electric shock, or injury to persons, pay close attention to this manual and stay within its guidelines when using this
product. Save these instructions for future use.
• Do not cover this product as the covering may cause product to overheat, melt, or ignite.
• Risk of fire or electric shock. Uncoil flexible light prior to plugging in. Do not operate HPR68 strip light while it is tightly coiled.
• Do not route the cord or HPR68 strip light through walls, ceilings, doors, windows, or any similar part of the building structure.
• Secure this flexible light using only factory recommended mounting channel (HPR68-24VDC-18MM-TRACM-3FT) and hardware (HPR68-
24VDC-18MM-CLIPS), sold separately.
• Do not secure this product or its cord with staples, nails, or like means that may damage the outer jacket or cord insulation.
• Do not use if there is any damage to the PU housing or power cord insulation. Inspect periodically.
• Do not install on gates or doors, where subject to continuous flexing.
• Do not install near flammable liquids or other flammable materials.
• The HPR68 strip light is a custom cut only product. Do not attempt to cut, splice, or modify in anyway.
• This product is designed for use by a qualified installer.
• This product is for decorative use only. Not to be used by children as a toy. Keep out of reach of small children.
• Do not exceed maximum run distance in any single inter-connected run: 10m (33ft) for single color and 5m (16.4ft) for RGB.
• Size your 24V DC driver appropriately for your run distance of HPR68 strip light using 10W per meter or 3.04W per foot for single color and
15W per meter or 4.57W per foot for RGB as a guide.
• Be sure not to load any driver to 100% as this will reduce its efficiency. A 90% maximum load is recommended for driver longevity.
• The rated ambient temperature range for HPR68 strip light is -10°C (14°F) to 50°C (122°F).
• The maximum bend radius of the Pool-Rated Neon series product is 120mm or 4.72". Do not twist, drop, hang, sag, or bend product in any way
other than intended. This product can only bend vertically in relation to its light output. See Figure 1 below for reference.
FIGURE 1
When using outdoor portable lighting products, basic safety precautions should always be followed to reduce the risk of
fire, electric shock, and personal injury, including the following:
• Use only factory recommended power and linking connections.
• Use ground fault circuit interrupter (GFCI) protection on the circuit(s) or outlet(s) when using outdoors.
• Use only UL approved outdoor extension cords, such as type SW, SOW, STW, STOW, SJW, SJOW, SJTW, or SJTOW. This designation is
marked on the jacket of the extension cord.
POOL-RATED NEON ITEM NUMBER
HPR68-24VDC-RGB-CC
HPR68-24VDC-SC-CC
HPR68-24VDC-SW-CC
*THIS PRODUCT IS A CUSTOM CUT PRODUCT ONLY AND IS NOT FIELD CUTTABLE. DO NOT CUT OR MODIFY THIS PRODUCT OR IT WILL VOID THE WARRANTY.
Cutting point measurements provided to calculate to correct length of product to order only.
©2023 American Lighting, Inc. REV2341 www.AmericanLighting.com
WARNING
WARNING
WARNING
Lighted
Surface
DESCRIPTION
WATTAGE
RGB
4.57W per ft
Single Color
3.04W per ft
Static White
3.04W per ft
Do not operate Pool-
Rated Neon strip light
while it is coiled or on
the reel.
To reduce the risk of fire, electric shock or injury to persons,
make sure that the electrical power to the fixture is
disconnected at the source prior to installation or any servicing.
>120mm
WARNING
MAX RUN
LUMEN OUTPUT
16.4ft
160Lm per ft
33ft
Up to 150Lm per ft,
Depending on Color
33ft
235Lm per ft
Page 1 of 5
11775 E. 45th Ave. Denver, CO 80239 Ph: 1-800-880-1180 Fax: 303-695-7633
Do not
Do not hang
droop or sag
WARNING
CONTROL TYPE/
CUTTING POINTS*
DIMMING
DMX
Every 2.46" (62.5mm)*
10-100% Dimming with
Every 3.94" (100mm)*
CL or ELV Dimmers
10-100% Dimming with
Every 3.94" (100mm)*
CL or ELV Dimmers
8

Advertisement

loading
Need help?

Need help?

Do you have a question about the HPR68-RGB and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for American Lighting HPR68-RGB

  • Page 1 To reduce the risk of fire, electric shock or injury to persons, use make sure that the electrical power to the fixture is this flexible light only with American Lighting/Prizm recommended disconnected at the source prior to installation or any servicing.
  • Page 2 POOL-RATED NEON STRIP LIGHT 24V DC INSTALLATION INSTRUCTIONS HPR68-RGB / HPR68-SC / HPR68-SW REQUIRED COMPONENTS (Figure 2): FIGURE 2 Appropriate Junction Box* Class 2-rated Driver*± Compatable Dimmer, Switch, or Controller* HPR68 Pool-Rated Neon Strip Light AC IN Mounting Brackets Mounting Channel...
  • Page 3: Mounting Bracket Installation

    POOL-RATED NEON STRIP LIGHT 24V DC INSTALLATION INSTRUCTIONS HPR68-RGB / HPR68-SC / HPR68-SW MOUNTING BRACKET INSTALLATION: FIGURE 4 To install using mounting brackets, start by determing the best location for the drivers, controllers, and junction boxes. Using the ruler, measure and mark placement spots for mounting brackets about 12"...
  • Page 4 POOL-RATED NEON STRIP LIGHT 24V DC INSTALLATION INSTRUCTIONS HPR68-RGB / HPR68-SC / HPR68-SW MOUNTING CHANNEL INSTALLATION: FIGURE 8 To install using mounting channel, start by determing the best location for the drivers, controllers, and junction boxes. Using the ruler, measure and mark placement spots for mounting channel about 12"...
  • Page 5 Cable Black Black (Positive When using a DMX controller to control HPR68-RGB, first connect appropriate 24V DC driver to the DMX controller ac- cording to the driver's instructions. Then, connect the Black Wire of the HPR68 power cable to the...

This manual is also suitable for:

Hpr68-scHpr68-sw