Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Bosch WSD274A0TC
Summary of Contents for Bosch WSD274A0TC
- Page 1 Washer dryer WSD274A0TC [en] User manual and installation instructions...
-
Page 2: Table Of Contents
Further information and explanations are available online: Table of contents 1 Safety ........... 4 8 Buttons ........ 25 1.1 General information.... 4 9 Dryness level...... 28 1.2 Intended use...... 4 9.1 Changing the dryness level.. 28 1.3 Restriction on user group.. 4 1.4 Safe installation ...... 5 10 Programmes ...... 29 1.5 Safe use ........ - Page 3 15 Childproof lock...... 37 21 Transportation, storage and disposal ........ 62 15.1 Activating the childproof lock ........ 37 21.1 Removing the appliance .. 62 15.2 Deactivating the childproof 21.2 Inserting the transit bolts.. 62 lock ........ 37 21.3 Using the appliance again .. 62 21.4 Disposing of old appliance ...
-
Page 4: Safety
en Safety 1 Safety Observe the following safety instructions. 1.1 General information ¡ Read this instruction manual carefully. ¡ Keep the instruction manual and the product information safe for future reference or for the next owner. ¡ Do not connect the appliance if it has been damaged in transit. 1.2 Intended use Only use this appliance: ¡... -
Page 5: Safe Installation
Safety en Without permission granted by the NCC, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as performance to a approved low power radio-frequency devices. The low power radio-frequency devices shall not influence aircraft security and interfere legal communications;... - Page 6 en Safety If the insulation of the power cord is damaged, this is dangerous. ▶ Never let the power cord come into contact with hot appliance parts or heat sources. ▶ Never let the power cord come into contact with sharp points or edges.
-
Page 7: Safe Use
Safety en CAUTION ‒ Risk of cutting! Touching sharp edges on the appliance may lead to cuts. ▶ Do not touch the sharp edges on the appliance. ▶ Wear protective gloves when installing and transporting the ap- pliance. 1.5 Safe use WARNING ‒ Risk of electric shock! If the appliance or the power cord is damaged, this is dangerous. - Page 8 en Safety WARNING ‒ Risk of explosion! If there is coal dust or flour in the air around the appliance, this may cause an explosion. ▶ Keep the area around the appliance clean during operation. WARNING ‒ Risk of poisoning! Detergents and care products may result in poisoning if con- sumed.
-
Page 9: Safe Cleaning And Maintenance
Safety en CAUTION ‒ Risk of injury! The covering plate may break if you stand on or climb onto the appliance. ▶ Do not stand on or climb onto the appliance. The appliance may tip over if you sit on or lean against the open door. - Page 10 en Safety ▶ If the power cord of this appliance is damaged, it must be re- placed by the manufacturer, the manufacturer's Customer Ser- vice or a similarly qualified person in order to prevent any risk. An ingress of moisture can cause an electric shock. ▶...
-
Page 11: Preventing Material Damage
Preventing material damage en Make sure that the valve housing ▶ Preventing material damage 2 Preventing material for the water inlet hose does not come into contact with its sur- damage roundings and is not subjected to any external forces. Preventing material damage ATTENTION! Ensure that the inner diameter of ▶... -
Page 12: Environmental Protection And Saving Energy
en Environmental protection and saving energy Do not use cleaning products with Reduce the washing temperature for ▶ a high alcohol content. lightly and normally soiled laundry. Do not use hard scouring pads or ▶ a At lower temperatures, the appli- cleaning sponges. -
Page 13: Installation And Connection
Installation and connection en Replace the accessories in ques- ▶ Installation and connection 4 Installation and con- tion before operating the appli- ance. nection → "Accessories", Page 33 Installation and connection Note: The appliance has been tested 4.1 Unpacking the appliance at the factory to check it is in working order. -
Page 14: Removing The Transit Bolts
en Installation and connection Pull the hoses out of the holders. Installation loca- Requirements tion Base Secure the appli- ance with fixing brackets. Wooden joist Place the appli- floor ance on a water- resistant wooden board (minimum Unscrew and remove all of thickness of the screws for the 4 transit bolts 30 mm) which is... -
Page 15: Connecting The Appliance
Installation and connection en Remove the 4 sleeves. 4.5 Connecting the appliance Connecting the water inlet hose Connect the water inlet hose. Put on the 4 cover caps. Connect the water inlet hose to a tap (26.4 mm = 3/4"). Push the 4 cover caps downwards. Open the water tap carefully and check that the connection points are tight. -
Page 16: Aligning The Appliance
en Installation and connection Note: Observe the draining heights. 4.6 Aligning the appliance The draining heights are: minimum: In order to reduce noise and vibra- 60 cm, maximum: 100 cm tion and to prevent the appliance Siphon Secure the con- from moving, align the appliance cor- nection point with rectly. - Page 17 Installation and connection en Use a WAF 17 wrench to tighten the lock nuts against the housing until they are hand-tight. In doing so, hold the foot tight and do not adjust its height.
-
Page 18: Detergent Drawer
en Familiarising yourself with your appliance Familiarising yourself with your appliance 5 Familiarising yourself with your appliance Familiarising yourself with your appliance 5.1 Appliance You can find an overview of the parts of your appliance here. On certain models, specific details such as the colour and shape may differ from those pictured. -
Page 19: Control Panel
Familiarising yourself with your appliance en Manual dosing compartment / : Dispenser for fabric softener or liquid detergent : Dispenser for liquid deter- gent 5.3 Control panel You can use the control panel to configure all functions of your appliance and to obtain information about the operating status. 5.4 Operating logic Programmes → Page 29 Buttons and display... - Page 20 en Familiarising yourself with your appliance tings by pressing the buttons. The ac- To display the additional buttons, tivated settings are highlighted briefly press 更多. brightly on the display. ATTENTION! Pressing on the display with force a The display shows all additional may cause damage.
-
Page 21: Before Using For The First Time
Before using for the first time en Start the first wash cycle or press Before using for the first time 6 Before using for the to put the appliance in standby mode. first time → "Basic operation", Page 34 Prepare the appliance for use. Before using for the first time 6.1 Starting an empty wash- ing cycle... -
Page 22: Display
en Display Display 7 Display The display shows the current settings, options or relevant information. Display Example: Display Display Description 0:40 Expected programme duration or programme time re- maining in hours and minutes. Program end time → "Buttons", Page 25 Recommendation for the maximum load capacity for the selected program in kg. - Page 23 Display en Display Description Orange The stain type is activated. Red wine The stain type is activated. Cooking fat/cooking oil The stain type is activated. Change the basic settings. Flashes: Drum cleaning is required. Run the 槽潔淨 pro- gramme for cleaning and caring for the drum and the outer tub.
- Page 24 en Display Display Description Flashes: The voltage control system has paused the pro- gramme due to impermissible voltage drops or voltage surges. → " flashes.", Page 51 Note: The programme continues when the voltage is per- missible again. The appliance has detected too much foam. → "...
-
Page 25: Buttons
Buttons en Buttons 8 Buttons The selection of programme settings depends on the programme that is set. Buttons Button Selection Description (mains ¡ Switch on Switch on the appliance or put it in switch) standby mode. ¡ Standby mode Multiple selection To change a setting, press the selection button until the display shows the required setting. - Page 26 en Buttons Button Selection Description ¡ Activate → "Childproof lock", Page 37 童鎖3秒 ¡ Deactivate ¡ Saving Press the button for approx. 3 最愛 seconds to save your customised pro- ¡ Setting gram settings. → "Saving the programme settings", Page 35 If you briefly press the button, you can set customised program settings for your program.
- Page 27 Buttons en Button Selection Description i-DOS 2 ¡ Activate Briefly press the button to activate or deactivate the intelligent dosing sys- ¡ Deactivate tem for fabric softener or liquid de- ¡ Dispenser contents tergent . ¡ Basic dosage Press the button for approx. 3 seconds to specify the contents of the dispenser or set the basic dosage.
-
Page 28: Dryness Level
en Dryness level Dryness level 9 Dryness level In some programmes, a dryness level is predefined. The dryness level defines Dryness level how dry or damp your laundry is after the programme ends. Dryness level Laundry Drying result ++ Multi-layered, thick laundry The laundry is dry. -
Page 29: Programmes
Programmes en Programmes 10 Programmes Programmes Note: The laundry's care labels provide you with additional information on pro- gramme selection. Programme Description Max. Max. load load (kg) (kg) Dry- Wash Rinse and then spin the laundry, and drain the – – 洗清 water. Programme setting: Max. - Page 30 en Programmes Programme Description Max. Max. load load (kg) (kg) Dry- Wash Note: To prevent excessive foaming, remove air from laundry items by rolling them up be- fore you wash them. Programme setting: ¡ Max. 60 °C ¡ Max. 1200 rpm Clean and care for the drum. –...
- Page 31 Programmes en Programme Description Max. Max. load load (kg) (kg) Dry- Wash Notes ¡ The laundry is not dried or washed. ¡ If you use the 清新除味 programme often without washing in between, this may cause odours in the appliance. Wash and dry items made from cotton, linen, 洗烘45' or synthetic or blended fabrics.
- Page 32 en Programmes Programme Description Max. Max. load load (kg) (kg) Dry- Wash Wash items made from cotton, or synthetic or 抗敏除蟎 blended fabrics. Suitable for killing and removing mites. Tip: Energy- and time-optimised programme using hybrid technology. Programme setting: ¡ Max. 60 °C ¡...
-
Page 33: Accessories
Accessories en Accessories 11 Accessories Use original accessories. These have been made especially for your appliance. Accessories Order num- Elbow Secure the water outlet hose in place. 00655300 Washing machine Cleaning products for maintaining the ap- 00311929 cleaners pliance interior. ¡ Spin the laundry before drying Laundry 12 Laundry ¡... -
Page 34: Detergents And Care
en Detergents and care products Fold the quilt together in the centre ¡ Do not use products that have ex- and fold in the upper and lower pired or are highly congealed parts of the quilt. ¡ Do not use products containing solvents, caustic agents or volatile substances ¡... -
Page 35: Adjusting The Programme Settings
Basic operation en Press the required programme. 14.4 Saving the programme → "Programmes", Page 29 settings You can save your individual pro- gramme settings as favourites. Requirements ¡ A programme is set. → "Setting a programme", Page 34 ¡ The programme settings have been adjusted. → "Adjusting the programme set- tings", Page 35 Press and hold 最愛... -
Page 36: Loading Laundry
en Basic operation a The drum rotates and load detec- 14.6 Loading laundry tion takes place. This can take up Note: To prevent creasing, note the to 2 minutes, after which water maximum load for the programmes. enters the drum. → "Programmes", Page 29 a The display shows the programme duration or the programme end Requirements time. -
Page 37: Cancelling The Drying Programme
Childproof lock en The appliance door remains Wipe the rubber gasket dry and re- locked for safety reasons if the move any foreign objects. temperature and water levels are high. – If the temperature is high, start the 洗清 programme. – If the water level is high, start the 脫水... -
Page 38: Starting The Programme With Intelligent Dosing Sys- Tem
en Intelligent dosing system Requirements Intelligent dosing system 16 Intelligent dosing sys- ¡ The laundry is prepared. → "Preparing the laundry", Page 33 ¡ The laundry is sorted. The optimum quantities of liquid de- ¡ The laundry is placed in the appli- Intelligent dosing system tergent and fabric softener are dis- ance. -
Page 39: Filling The Dispensers
Intelligent dosing system en Pour liquid detergent and fabric 16.2 Filling the dispensers softener into the relevant dis- If you want to use the intelligent dos- pensers. ing system or if the appliance dis- → "Detergent drawer", Page 18 plays a notification during operation of the appliance, fill the dispensers. -
Page 40: Basic Dosage
en Home Connect To set , press i-DOS 2. The Home Connect app guides you through the entire login process. Fol- a The display shows . low the instructions in the Home Con- To set , press i-DOS 2 again. nect app to configure the settings. To end the setting process, wait Tips briefly. -
Page 41: Home Connect Menu
Home Connect en Follow the instructions in the 17.5 Deactivating Wi-Fi on the Home Connect app. appliance 17.3 Home Connect menu Requirements ¡ The Home Connect menu is called The Home Connect menu contains all of the Home Connect settings. → "Calling up the Home Connect menu", Page 41 Calling up the Home Connect ¡... -
Page 42: Data Protection
en Home Connect Note: Please note that the Activating remote start Home Connect functions can only be Requirements utilised with the Home Connect app. ¡ The appliance is connected to your Information on data protection can be home WiFi network. retrieved in the Home Connect app. ¡... -
Page 43: Basic Settings
Basic settings en Basic settings 18 Basic settings You can configure the basic settings for your appliance to meet your needs. Basic settings 18.1 Overview of the basic settings Posi- Basic setting Selection Description tion End signal 0 (off) Set the volume of the signal at the 1 (quiet) end of the programme. -
Page 44: Changing The Basic Set- Tings
en Cleaning and servicing cleaning agent for caring for the in- 18.2 Changing the basic set- side of the appliance. tings → "Accessories", Page 33 To call up the basic settings, press 19.2 Cleaning the detergent and hold 更多 for approx. 3 seconds. drawer a The display shows If you want to replace the liquid de- Select the required basic setting. - Page 45 Cleaning and servicing en Remove the pump unit. Clean the pump unit with a damp cloth. Unclip the detergent drawer cover and remove it. Clean the detergent drawer and the cover with a soft, damp cloth or hand shower. Empty the detergent drawer. Dry the detergent drawer, cover and pump unit and reinsert them.
-
Page 46: Cleaning The Drain Pump
en Cleaning and servicing Open and remove the mainten- ance flap. Clean the housing of the detergent drawer in the appliance. Slide a sufficiently large container under the opening. Push in the detergent drawer. 19.3 Cleaning the drain pump Take the drain hose out of the holder. - Page 47 Cleaning and servicing en Cleaning the drain pump CAUTION - Risk of scalding! When you wash at high temperat- Requirement: The drain pump is ures, the detergent solution gets empty. → Page 46 hot. Since water may remain in the Do not touch the hot detergent ▶...
-
Page 48: Cleaning The Intake Opening In The Rubber Gasket
en Cleaning and servicing Ensure that both impellers can Insert and close the maintenance turn. flap. Insert the pump cap. 19.4 Cleaning the intake Ensure that the parts of the ‒ opening in the rubber pump cap are correctly as- sembled. gasket Regularly check the intake opening in the rubber gasket for any block- ages and clean the intake opening. -
Page 49: Troubleshooting
Troubleshooting en Troubleshooting 20 Troubleshooting You can rectify minor faults on your appliance yourself. Read the troubleshoot- Troubleshooting ing information before contacting after-sales service. This will avoid unneces- sary costs. WARNING Risk of electric shock! Incorrect repairs are dangerous. Repairs to the appliance should only be carried out by trained specialist ▶... - Page 50 en Troubleshooting Fault Cause and troubleshooting "E:30 / -80" Ensure that the drain pipe and water drain hose are ▶ not kinked or trapped. The water outlet hose is connected too high. Install the water outlet hose at a maximum height of ▶...
- Page 51 Troubleshooting en Fault Cause and troubleshooting The pump unit is not inserted. Insert the pump unit into the detergent drawer. → "Cleaning the detergent drawer", Page 44 Push in the detergent drawer until the symbol goes out. lights up. The temperature is too high. Wait until the temperature has dropped.
- Page 52 en Troubleshooting Fault Cause and troubleshooting All other error codes. Malfunction Switch the appliance off and then on again. If the message appears again, disconnect the appli- ance from the power supply for at least 30 seconds by pulling out the plug or by switching off the relev- ant circuit breaker in the fuse box.
- Page 53 Troubleshooting en Fault Cause and troubleshooting The programme does Door is not closed. not start. Close the door. ▶ Childproof lock is activated. Deactivate childproof lock. ▶ → "Deactivating the childproof lock", Page 37 預約 is activated. Check whether 預約 is activated. ▶ → "Buttons", Page 25 Laundry is caught in the door.
- Page 54 en Troubleshooting Fault Cause and troubleshooting The water is not drain- → "Cleaning the drain pump", Page 46 ▶ ing. The water outlet hose is connected too high. Install the water outlet hose at a maximum height of ▶ 1 metre. Pump cover is not correctly assembled. Correctly assemble the pump cover.
- Page 55 Troubleshooting en Fault Cause and troubleshooting The spin cycle runs The unbalanced load detection system eliminates an several times. imbalance by repeatedly redistributing the laundry. Not a fault – no action required. ▶ Note: When loading, where possible, place large and small items of laundry together in the drum. Different sized items of laundry distribute themselves better during the spin cycle.
- Page 56 en Troubleshooting Fault Cause and troubleshooting High spin speed not A low spin speed is selected. reached. The next time you run a wash cycle, set a higher ▶ spin speed. Unbalance load detection system is using a reduced spin speed to eliminate an unbalance. Redistribute the laundry in the drum.
- Page 57 Troubleshooting en Fault Cause and troubleshooting Insufficient cleaning. Drain the dispenser. → "Cleaning the detergent drawer", Page 44 Clean the dispenser. Refill the dispenser. → "Filling the dispensers", Page 39 Unsuitable detergent added to the dispenser of the in- telligent dosing system. Check whether the detergent used is suitable. → "Detergents and care products", Page 34 Drain the dispenser.
- Page 58 en Troubleshooting Fault Cause and troubleshooting Detergent residue on Detergents may contain water-insoluble substances the damp washing. that deposit on the laundry. Start the 洗清 programme. ▶ Unsuitable detergent added to the dispenser of the in- telligent dosing system. Check whether the detergent used is suitable. → "Detergents and care products", Page 34 Drain the dispenser.
- Page 59 Troubleshooting en Fault Cause and troubleshooting cannot be oper- Drying phase active. ated. Not a fault – no action required. ▶ Drying programme Door is not closed. does not start. Close the door. ▶ No drying programme is selected. Select a suitable drying programme. ▶...
- Page 60 en Troubleshooting Fault Cause and troubleshooting The laundry is too Make sure that the water tap also remains open ▶ damp. during the drying phase. The ambient temperature is greater than 30 °C. Ensure that the ambient temperature is below 30 ▶ °C.
- Page 61 Troubleshooting en Fault Cause and troubleshooting Spin noise during the Thermal spinning is active. drying phase. Not a fault – normal operating noise. ▶ Rushing, hissing Water is flushed under pressure into the detergent noise. drawer. Not a fault – normal operating noise. ▶...
-
Page 62: Emergency Release
en Transportation, storage and disposal Empty the dispensers. 20.1 Emergency release Releasing the door 21.2 Inserting the transit bolts Requirement: The drain pump is empty. → Page 46 Secure the appliance before trans- ATTENTION! Escaping water may portation using transit bolts in order cause material damage. to prevent transport damage. -
Page 63: Disposing Of Old Appliance
Customer Service directory or on our With redundant appliances, unplug ▶ website. the power cord. Then cut through Please visit: https://www.bosch- the cord and damage the lock on home.com.tw/specials/rohs for the appliance door beyond repair Taiwan Restriction of the use of cer-... -
Page 64: Declaration Of Conformity
Directive stallation protec- 2014/53/EU. tion A detailed RED Declaration of Con- Nominal power 2000 W formity can be found online at www.bosch-home.com among the Water pressure ¡ Minimum: additional documents on the product 100 kPa page for your appliance. (1 bar) ¡ Maximum: 1000 kPa... - Page 68 Expert advice for your Bosch home appliances, help with problems or a repair from Bosch experts. Find out everything about the many ways Bosch can support you: www.bosch-home.com/service Contact data of all countries are listed in the attached service direct- ory.
Need help?
Do you have a question about the WSD274A0TC and is the answer not in the manual?
Questions and answers