Page 1
Washer dryer WSD274A0TC [en] User manual and installation instructions...
Page 2
Further information and explanations are available online: Table of contents 1 Safety ........... 4 8 Buttons ........ 24 1.1 General information.... 4 9 Programmes ...... 27 1.2 Intended use...... 4 1.3 Restriction on user group.. 4 10 Accessories...... 31 1.4 Safe installation ...... 5 11 Laundry........ 31 1.5 Safe use ........
Page 3
16 Intelligent dosing system .. 35 21.2 Inserting the transit bolts.. 53 16.1 Pouring liquid detergent 21.3 Using the appliance again .. 53 and fabric softener into the 21.4 Disposing of old appliance ... 53 dispensers ...... 36 16.2 Using the manual dosing 22 Customer Service.... 54 compartment ......
Page 4
en Safety 1 Safety Observe the following safety instructions. 1.1 General information ¡ Read this instruction manual carefully. ¡ Keep the instruction manual and the product information safe for future reference or for the next owner. ¡ Do not connect the appliance if it has been damaged in transit. 1.2 Intended use Only use this appliance: ¡...
Page 5
Safety en Without permission granted by the NCC, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as performance to a approved low power radio-frequency devices. The low power radio-frequency devices shall not influence aircraft security and interfere legal communications;...
Page 6
en Safety If the insulation of the power cord is damaged, this is dangerous. ▶ Never let the power cord come into contact with hot appliance parts or heat sources. ▶ Never let the power cord come into contact with sharp points or edges.
Page 7
Safety en CAUTION ‒ Risk of cutting! Touching sharp edges on the appliance may lead to cuts. ▶ Do not touch the sharp edges on the appliance. ▶ Wear protective gloves when installing and transporting the ap- pliance. 1.5 Safe use WARNING ‒ Risk of electric shock! If the appliance or the power cord is damaged, this is dangerous.
Page 8
en Safety WARNING ‒ Risk of suffocation! Children may breathe in or swallow small parts, causing them to suffocate. ▶ Keep small parts away from children. ▶ Do not let children play with small parts. WARNING ‒ Risk of explosion! If there is coal dust or flour in the air around the appliance, this may cause an explosion.
Page 9
Safety en WARNING ‒ Risk of fire! If drying is interrupted early, the laundry is not cooled sufficiently and may ignite. ▶ Do not interrupt the drying programme early. ▶ If drying is interrupted early, remove the laundry immediately and spread it out. CAUTION ‒ Risk of injury! The covering plate may break if you stand on or climb onto the appliance.
Page 10
en Safety 1.6 Safe cleaning and maintenance WARNING ‒ Risk of electric shock! Improper repairs are dangerous. ▶ Never make any technical modifications to the appliance or its features. ▶ Repairs to the appliance should only be carried out by trained specialist staff. ▶ Only use genuine spare parts when repairing the appliance. ▶...
Page 11
Preventing material damage en Connect the water inlet hose dir- ▶ Preventing material damage 2 Preventing material ectly to the water tap, without any additional connecting elements damage such as adapters, extensions or valves. Preventing material damage ATTENTION! Make sure that the valve housing ▶...
Page 12
en Environmental protection and saving energy Unsuitable cleaning products may 3.3 Energy saving mode damage the surfaces of the appli- If you do not use the appliance for a ance. brief period, it automatically switches Do not use harsh or abrasive de- ▶...
Page 13
Installation and connection en ATTENTION! 4.2 Contents of package If residual water in the appliance After unpacking all parts, check for freezes, this may cause damage to any damage in transit and complete- the appliance. ness of the delivery. Do not install or operate this appli- ▶...
Page 14
en Installation and connection Unscrew and remove all of Installation loca- Requirements the screws for the 4 transit bolts tion using a WAF 13 wrench. Against a wall Do not trap the power cord or the hoses between the wall and the appli- ance.
Page 15
Installation and connection en Put on the 4 cover caps. Connect the water inlet hose to a tap (26.4 mm = 3/4"). Push the 4 cover caps downwards. Open the water tap carefully and check that the connection points are tight. Water outlet connection types This information is intended to help you to connect this appliance to the water outlet.
Page 16
en Installation and connection 4.6 Aligning the appliance Sink Fix and secure the water outlet In order to reduce noise and vibra- hose with an el- tion and to prevent the appliance bow. from moving, align the appliance cor- → "Accessories", rectly. Page 31 Use a WAF 17 wrench to loosen the lock nuts in a clockwise direc- Plastic pipe with...
Page 17
Before using for the first time en Use a WAF 17 wrench to tighten Pour approx. 1 litre of water into the lock nuts against the housing the manual dosing compartment. until they are hand-tight. Add washing powder containing In doing so, hold the foot tight and oxygen bleach to the manual dos- do not adjust its height.
Page 18
en Familiarising yourself with your appliance Familiarising yourself with your appliance 6 Familiarising yourself with your appliance Familiarising yourself with your appliance 6.1 Appliance You can find an overview of the parts of your appliance here. On certain models, specific details such as the colour and shape may differ from those pictured.
Page 19
Familiarising yourself with your appliance en Manual dosing compartment → "Using the manual dosing compartment", Page 36 / : Dispenser for fabric softener or liquid detergent → "Intelligent dosing system", Page 35 : Dispenser for liquid deter- gent → "Intelligent dosing system", Page 35 6.3 Control panel You can use the control panel to configure all functions of your appliance and to obtain information about the operating status.
Page 20
en Familiarising yourself with your appliance tings by pressing the buttons. The ac- To display the additional buttons, tivated settings are highlighted briefly press 更多. brightly on the display. ATTENTION! Pressing on the display with force a The display shows all additional may cause damage.
Page 21
Display en Display 7 Display The display shows the current settings, options or relevant information. Display Example: Display Display Description 0:40 Expected programme duration or programme time re- maining in hours and minutes. Program end time → "Buttons", Page 24 Recommendation for the maximum load capacity for the selected program in kg.
Page 22
en Display Display Description The "Cooking fat/cooking oil" stain type is activated. Change the basic settings. → Page 40 Flashes: Drum cleaning is required. Run the 槽潔淨 pro- gramme for cleaning and caring for the drum and the outer tub. → "Cleaning the drum and cleaning fluff", Page 40 ¡...
Page 23
Display en Display Description ¡ Lights up: The door is locked. – To add laundry, the door can be unlocked. → "Adding laundry", Page 34 – To open the door, you can cancel the programme. → "Cancelling the washing programme", Page 34 ¡ Flashes: The door is not closed. ¡...
Page 24
en Buttons Buttons 8 Buttons The selection of programme settings and options to change these depend on Buttons the programme that is set as well as the programme status. Button Selection Description (mains ¡ Switch on Switch on the appliance or put it in switch) standby mode.
Page 25
Buttons en Button Selection Description ¡ +1 Activate or deactivate up to three ad- 加洗清 ditional rinse cycles. ¡ +2 Recommended for particularly sensit- ¡ +3 ive skin or in regions with very soft water. ¡ Activate → "Childproof lock", Page 35 童鎖3秒 ¡...
Page 26
en Buttons Button Selection Description i-DOS 2 ¡ Activate Briefly press the button to activate or deactivate the intelligent dosing sys- ¡ Deactivate tem for fabric softener or liquid de- ¡ Adapting the dis- tergent . penser Press the button for approximately 3 ¡...
Page 27
Programmes en Programmes 9 Programmes Programmes Note: The laundry's care labels provide you with additional information about programme selection. Programme Description Max. Max. load load (kg) (kg) Dry- Wash- Rinse and then spin the laundry, and drain the – – 洗清 water. Programme setting: Max. 1400 rpm Spin the laundry and drain the water.
Page 28
en Programmes Programme Description Max. Max. load load (kg) (kg) Dry- Wash- Note: To prevent excessive foaming, remove air from laundry items by rolling them up be- fore you wash them. Programme setting: ¡ Max. 60 °C ¡ Max. 1200 rpm – Clean and care for the drum. –...
Page 29
Programmes en Programme Description Max. Max. load load (kg) (kg) Dry- Wash- – Reduce creases and airborne odours in suits, 清新除味 shirts, down-filled fabrics, outdoor clothing and items made of cotton, cashmere or silk. Tip: To prevent creasing, remove the laundry immediately after the programme has ended. Notes ¡...
Page 30
en Programmes Programme Description Max. Max. load load (kg) (kg) Dry- Wash- Programme setting: ¡ Max. 60 °C ¡ Max. 1400 rpm Wash items made from cotton or synthetic 抗敏除蟎 fabrics. Suitable for killing and removing mites. Tip: Energy- and time-optimised programme using hybrid technology. Programme setting: ¡...
Page 31
Accessories en Accessories 10 Accessories Use original accessories. These have been made especially for your appliance. Accessories Order num- Elbow Secure the water outlet hose in place. 00655300 Washing machine Cleaning products for maintaining the ap- 00311929 cleaners pliance interior. ¡ Spin the laundry before drying Laundry 11 Laundry ¡...
Page 32
en Detergents and care products Fold the quilt together in the centre ¡ Do not mix different liquid deter- and fold in the upper and lower gents parts of the quilt. ¡ Do not mix detergent and fabric softener ¡ Do not use products that have ex- pired or are highly congealed ¡...
Page 33
Basic operation en Press the required programme. 13.4 Opening the door → "Programmes", Page 27 Press on the edge of the door. a The display shows the programme Open the door. settings. Adjust the programme settings. → "Buttons", Page 24 Observe the information about op- erating logic → Page 19. The programme settings are not saved permanently for the pro- gramme.
Page 34
en Basic operation Press 13.6 Starting the programme Note: If the intelligent dosing system 13.8 Cancelling the washing is activated, make sure that the dis- programme pensers have been filled → Page 36 and the basic dosage has been set Press → Page 37. Open the door. → Page 33 Requirement: A programme is set.
Page 35
Dryness level en Wipe the rubber gasket dry and re- Childproof lock 15 Childproof lock move any foreign objects. Secure your appliance against being Childproof lock operated unintentionally using the controls. 15.1 Activating the childproof lock Press and hold 童鎖3秒 for approx. ▶ 3 seconds.
Page 36
en Intelligent dosing system Open the lid and pour liquid deter- 16.1 Pouring liquid detergent gent and fabric softener into and fabric softener into the relevant dispensers the dispensers → Page 18. If you are using the intelligent dosing system or if the appliance displays a notification during operation of the appliance, fill the dispensers.
Page 37
Home Connect en Press and hold i-DOS 1 for approx. 16.3 Adapting the / dis- 3 seconds. penser a The display shows the set basic / dispenser can dose fabric dosage amount. softener or liquid detergent . To adjust the setting, press When it leaves the factory, the dis- Wait briefly to save the setting.
Page 38
en Home Connect 17.1 Setting up the 17.4 Deactivating Wi-Fi on the Home Connect app appliance Install the Home Connect app on Press and hold 遠端遙控 for ap- your mobile device. prox. 3 seconds. Start the Home Connect app and Press 遠端遙控 repeatedly until the set up access for Home Connect. display shows "on".
Page 39
Basic settings en This initial registration prepares the 17.7 Remote start Home Connect functions for use and Enable the appliance for remote start is only required when you want to via the Home Connect app. use the Home Connect functions for the first time. Note Remote start will be deactivated in Note: Please note that the the following circumstances:...
Page 40
en Cleaning and servicing once a year. Also clean the drum if Set the display brightness: you find fluff on the laundry after dry- 1 (low) to 4 (very high) ing. Activate (on) or deactivate (oFF) the reminder to clean CAUTION the drum.
Page 41
Cleaning and servicing en Put the appliance into standby Empty the detergent drawer. mode. → Page 34 Pull out the detergent drawer. Press down on the insert and re- move the detergent drawer. Clean the pump unit with a damp cloth. Remove the pump unit. Clean the detergent drawer and the cover with a soft, damp cloth or hand shower.
Page 42
en Cleaning and servicing 19.3 Cleaning the drain pump Clean the drain pump regularly, at least once a year, as well as in the event of faults, e.g. blockages or rat- tling noises. Emptying the drain pump Turn off the tap. Put the appliance into standby mode.
Page 43
Cleaning and servicing en Take the drain hose out of the Once emptied, press firmly on the holder. locking cap. Insert the drain hose into the CAUTION - Risk of scalding! holder. When you wash at high temperat- ures, the detergent solution gets hot.
Page 44
en Cleaning and servicing Since water may remain in the Ensure that both impellers can drain pump, unscrew the pump turn. cap carefully. The filter insert in the pump ‒ housing may become stuck due to coarse particles of dirt. Loosen the dirt and remove the filter insert.
Page 45
Cleaning and servicing en Insert and close the maintenance flap. 19.4 Cleaning the intake opening in the rubber gasket Regularly check the intake opening in the rubber gasket for any block- ages and clean the intake opening. Open the appliance door. Remove any blockages from the intake opening.
Page 46
en Troubleshooting Troubleshooting 20 Troubleshooting You can rectify minor faults on your appliance yourself. Read the troubleshoot- Troubleshooting ing information before contacting after-sales service. This will avoid unneces- sary costs. WARNING Risk of electric shock! Improper repairs are dangerous. Never make any technical modifications to the appliance or its features. ▶...
Page 47
Troubleshooting en Fault Cause and troubleshooting E:10 -00 -10 -20 The pump for the intelligent dosing system is blocked. Clean the detergent drawer. → Page 40 If the fault persists, call customer service. → Page 54 Note: Until the fault is rectified, you can deactivate the intelligent dosing system and dose manually.
Page 48
en Troubleshooting Fault Cause and troubleshooting All other error codes. Malfunction To restart the appliance, press and hold for ap- proximately 5 seconds. If the fault occurs again, disconnect the appliance from the power supply for at least 30 seconds. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box.
Page 49
Troubleshooting en Fault Cause and troubleshooting The display and but- Software fault. tons do not respond. To restart the appliance, press and hold for ap- proximately 5 seconds. If the fault occurs again, disconnect the appliance from the power supply for at least 30 seconds. Un- plug the appliance from the mains or switch off the circuit breaker in the fuse box.
Page 50
en Troubleshooting Fault Cause and troubleshooting The spin cycle runs Not a fault. The appliance eliminates an imbalance by several times. repeatedly redistributing the laundry. No action required. The appliance is vi- Appliance is not correctly aligned. brating, 'wandering' Align the appliance. → Page 16 ▶...
Page 51
Troubleshooting en Fault Cause and troubleshooting Insufficient cleaning or The detergent in the dispenser is unsuitable or detergent residues on thickened. the laundry. Check whether the detergent is suitable. → Page 32 Check whether the detergent in the dispenser has thickened. If the detergent is unsuitable or has thickened, empty it out and clean the dispenser.
Page 52
en Troubleshooting Fault Cause and troubleshooting Creasing. The selected programme is unsuitable for the type of fabric. Set a suitable programme. → Page 27 ▶ A high spin speed is selected. The next time you run a wash cycle, set a lower ▶ spin speed.
Page 53
Transportation, storage and disposal en 20.1 Emergency release 21.2 Inserting the transit bolts Releasing the door Secure the appliance before trans- Requirement: The drain pump is portation using transit bolts in order empty. → Page 42 to prevent transport damage. ATTENTION! Escaping water may Use a screwdriver to remove the 4 cause material damage.
Page 54
Customer Service directory or on our Maximum load 12.0 kg website. Mains voltage 220 V, 60 Hz Please visit: https://www.bosch- Minimum in- 10 A home.com.tw/specials/rohs for Taiwan Restriction of the use of cer- stallation protec- tion tain Hazardous Substances (RoHS) information.
Page 55
150 cm A detailed RED Declaration of Con- ter outlet hose formity can be found online at Length of the 201 cm www.bosch-home.com among the power cord additional documents on the product page for your appliance. Declaration of Conformity 24 Declaration of Con- formity 2.4 GHz band (2400–2483.5 MHz):...
Page 56
Expert advice for your Bosch home appliances, help with problems or a repair from Bosch experts. Find out everything about the many ways Bosch can support you: www.bosch-home.com/service Contact data of all countries are listed in the attached service direct- ory.
Need help?
Do you have a question about the WSD274A0TC and is the answer not in the manual?
Questions and answers