Download  Print this page

Bosch WVH28420GB Installation & Maintenance Instructions Manual

Automatic washer dryer logixx 7
Hide thumbs

Advertisement

Safety instructions
– The washer dryer is heavy – take care when lifting it.
– Warning: frozen hoses may tear/burst. Do not install the washer dryer outdoors or in areas
where there is a risk of frost.
– The washer dryer may be damaged. Do not lift by projecting components (e.g. washer dryer
door).
– In addition to the instructions mentioned here, special regulations of the relevant water and
power supply companies may apply.
– If in doubt, have the appliance connected by a technician.
– Lay hoses and cables in such a way that there is no risk that they can be tripped over.
Environmental disposal
– Dispose of packaging in an environmentally friendly manner.
– This appliance has been identified in accordance with the European Directive
2002/96/EEC on Waste Electrical and Electronic Equipment (WEEE). The Directive
specifies a framework for the return and recycling of waste appliances and is valid
throughout Europe.
Scope of delivery
Humidity in the drum is caused
by the final inspection.
Aqua-Stop
Aqua-Secure
Standard
Water drainage
Power cord
Water supply
Covers
Hose holder
Depending on the connection
– A 24–40 mm dia. hose clip may also be required for connecting the siphon (available from
specialist retailers).
Page 4: Water connection
Useful tool
– Spirit level for aligning the washer dryer.
– Wrench for adjusting the machine feet.
1
Installation area
– Stability is important to prevent the machine from wandering.
– The installation area must be firm and level.
– Soft floors/floor coverings are not suitable.
– Ensure the area is well ventilated to achieve good drying performance.
If installing the appliance on a pedestal
– It is essential to secure the washer dryer feet with holding brackets *.
If installing the appliance on a wooden joist floor
– If possible, install the washer dryer in a corner.
– Screw a water-resistant wooden panel (min. 30 mm thick) to the floor.
– It is essential to secure the washer dryer feet with holding brackets *.
* order no. WMZ 2200, WX 9756
Hose and cable lengths
Connection on left side
or
Connection on right side
~140 cm
~90 cm
~95 cm
~140 cm
~160 cm
~165 cm
Note: if hose holders are used, the hose lengths may be reduced.
Available from dealer/customer service:
– Aqua-Stop extension hose **, approx. 2.50 m.
– Longer supply hose, approx. 2.20 m, for standard model.
** order no. WMZ 2380, WZ 10130
Built-under/Built-in appliance
Build-under/build-in before connection to the power supply.
Installed in between kitchen units (built-under or built-in)
e
– Dimension requirement of kitchen unit:
f
a = 650 mm, b = 620 mm, c = 850 mm
– Install washer dryer only under a continuous worktop that
is connected firmly to the adjacent cupboards.
– The installation area must be well ventilated, otherwise the
washer dryer will operate below optimum performance.
Dimension of ventilation cross-section:
d x e = 200 mm x 100 mm, f = 365 mm
2
Distance between wall and machine: 50 mm
Removing transport bolts
– Before using the appliance for the first time, always remove and retain
all 4 transport bolts.
– If transporting the appliance subsequently, always re-install the
transport bolts – this prevents damage to the machine.
Page 6
– Retain the screw and sleeve.
1. Take the hoses out of the holder and the elbow.
2. Undo and remove all 4 transport bolts.
3. Take the power cord out of the holders. Remove the sleeves.
4. Insert the covers and lock them in place by pressing on the locking hook. Insert the hose
holders.
5. Fix the hoses in the hose holders.
3
Water connection
– Risk of electric shock! Do not immerse the Aqua-Stop safety device in water
(contains an electric valve).
– To prevent leakage or water damage, follow the instructions in this chapter.
– Attention: operate the washer dryer with cold drinking water only.
Do not connect to the mixer tap of a pressureless hot-water heater.
– Do not use a used inlet hose. Only use the inlet hose supplied or one which
was purchased from an authorised specialist dealer.
– If in doubt, have the appliance connected by a technician.
Water supply
Water inlet hose:
Attention: do not kink, crush, modify or cut through (strength is no longer guaranteed).
Optimum water pressure in the mains: 100–1000 kPa (1–10 bar)
– When the tap is turned on, the water flow is at least 8 l/min.
– If the water pressure is higher, install a pressure reducing valve.
Model:
Aqua-Stop
Standard
Aqua-Secure
1. Connect the water supply hose to the tap.
3/4 ''
Tighten plastic screw fittings by hand only.
min. 10 mm
max.
max.
2. Carefully turn on the tap and check that the
90°
90°
connection points are not leaking.
3/4 ''
Attention: the screw connection is under
water mains pressure.
min 10 mm
Water drainage
Water drainage hose:
Attention: do not kink or stretch.
Height difference between installation area and outlet: 60–100 cm
Drainage into a sink/bath tub:
Attention: secure the drainage hose to prevent it from slipping out
of the sink.
Attention: the plug must not be in the plug hole. When the water is being
pumped out of the washer dryer, check that the water drains away quickly
enough. Do not immerse the end of the drainage hose in the water that has
been pumped out. There is a risk that water will be drawn back into the
washer dryer.
Drainage into a siphon:
Attention: secure the connection with a 24–40 mm dia. hose clip (available
from a specialist retailer).
Drainage into a plastic pipe with rubber sleeve:
Attention: Secure the drainage hose to prevent it from slipping out
of the drain.
4
Alignment
High levels of noise, intense vibrations and "wandering" may be due to incorrect alignment.
Alignment will be carried out by customer service or authorised technicians, if you want
to align the machine by yourself please use a spirit level.
Aligning the washer dryer with a spirit level.
1. Undo the lock nut in a clockwise direction using a wrench.
2. Adjust the height by turning the appliance foot.
All four appliance feet must be placed firmly on the floor.
The washer dryer must not be able to wobble.
Check the alignment of the washer dryer with a spirit level and
correct if necessary.
3. Tighten the lock nut against the housing.
Hold the foot in place and make sure that the height is not adjusted.
The lock nuts on all four appliance feet must be screwed tightly against
the housing.
Electrical connection
Connect the washer dryer to an alternating current via a correctly installed earthed socket
only.
The mains voltage and specifications on the washer dryer must match.
Page 6: Technical specifications
For information about the connected load and required fuse.
Page 6: Technical specifications
Ensure that:
– the mains plug and socket are compatible,
– the cable cross-section is adequate,
– the earthing system has been installed correctly.
A damaged power cord may be replaced by an electrician only.
A replacement power cord is available from customer service.
Do not use multiple plugs/connectors or extension cables.
If a residual current operated circuit-breaker is used, use only a type which guarantees
compliance with the currently valid regulations.
Mains plug:
– do not insert into/pull out of the socket with damp hands.
– do not pull the plug out of the socket by pulling on the power cord.
– never pull out the plug while the appliance is in operation.
5
Manufacturer (see Operating instructions)
0810 / 9000 479252

Advertisement

Table of Contents
loading

  Summary of Contents for Bosch WVH28420GB

  • Page 1 Safety instructions Installation area – Stability is important to prevent the machine from wandering. – The washer dryer is heavy – take care when lifting it. – The installation area must be firm and level. – Warning: frozen hoses may tear/burst. Do not install the washer dryer outdoors or in areas –...
  • Page 2 Transportation, e.g. if moving house Care Before transporting the washer dryer: Machine housing, control panel – Wipe with a soft, damp cloth. – Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners). 1. Turn off the tap. –...
  • Page 3: Safety Instructions

    Safety instructions – The washer dryer is heavy – take care when lifting it. – Warning: frozen hoses may tear/burst. Do not install the washer dryer outdoors or in areas where there is a risk of frost. – The washer dryer may be damaged. Do not lift by projecting components (e.g. washer dryer door).
  • Page 4: Removing Transport Bolts

    Removing transport bolts – Before using the appliance for the first time, always remove and retain all 4 transport bolts. – If transporting the appliance subsequently, always re-install the transport bolts – this prevents damage to the machine. – Retain the screw and sleeve. 1.
  • Page 5: Alignment

    Alignment High levels of noise, intense vibrations and “wandering” may be due to incorrect alignment. Alignment will be carried out by customer service or authorised technicians, if you want to align the machine by yourself please use a spirit level. Aligning the washer dryer with a spirit level.
  • Page 6: Transportation, E.g. If Moving House

    Transportation, e.g. if moving house Before transporting the washer dryer: 1. Turn off the tap. 2. Release the water pressure in the supply hose. Page 8: Filter in the water inlet hose 3. Drain any residual detergent solution. Page 8: Drain pump 4.
  • Page 7: Maintenance

    – Risk of scalding! Allow detergent solution to cool down! Maintenance – Turn off the tap! Drain pump Set the programme selector to Off, disconnect the mains plug. 1. Open and remove the service flap. 2. Release the drainage hose from the clip. Remove the sealing plug from the drainage hose, allow the detergent solution to flow out.
  • Page 8: Table Of Contents

    Washer dryer Installation maintenance instructions Contents Safety instructions ......1 Environmental disposal ......1 Scope of delivery.