Harken WINGMAN MH Product Manual

MANUFACTURER:
USA
Harken, Inc.
N15W24983 Bluemound Rd.
Pewaukee, WI, 53072
WARNING!
ACTIVITIES INVOLVING THE USE OF THIS EQUIPMENT ARE
INHERENTLY DANGEROUS. YOU ARE RESPONSIBLE FOR
YOUR OWN ACTIONS AND DECISIONS.
THIS DEVICE IS NOT INTENDED FOR HUMAN SUSPENSION.
BEFORE USING THIS EQUIPMENT, YOU MUST:
 Read and understand all instructions for use
Material Handling WINGMAN - Red annodized, black rope
 Get specific training in the Wingman MH proper use
 Become acquainted with its capabilities and limitations
 Understand and accept the risks involved
FAILURE TO HEED ANY OF THESE WARNINGS MAY RESULT
No etching on this side
IN SEVERE INJURY OR DEATH
of upper block.
WARNING!
DO NOT EXCEED RECOMMENDED WORKING LOAD.
AVOID SHOCK LOADING.
PRODUCT MARKINGS
Red Block:
Load Diagram:
WLL & Rope Diameter
WORKING LOAD:
3 kN (675 lb)
BREAK LOAD:
FOR QUOTATION PURPOSES ONLY
45 kN (10, 1 16 lb)
1. USE
INCORPORATED
- ALL DIMENSIONS PRIOR TO FINISHING
- REMOVE ALL BURRS AND BREAK SHARP
N15 W24983 Bluemound Road
- The Wingman MH is a mechanical-advantage device for load lifting and releasing.
EDGES WITH 0.010 MAX RADIUS OR
Pewaukee, Wisconsin 53072
Tel: 262-691-3320
TOLERANCES UNLESS OTHERWISE SPECIFIED:
- This product is intended to be used by competent persons familiar with the use of
Fax: 262-691-3807
DECIMAL:
www.harken.com
pulleys for lifting.
ANGULAR:
- Use only with supplied rope.
- To prolong the life of this product, care in use is necessary. Avoid rubbing against
DIMENSIONS IN OVALS ARE KEY abrasive surfaces and sharp edges.
PRODUCT CHARACTERISTICS
- The Wingman MH is not certified for fall arrest, suspension, or positioning of a
UNLESS OTHERWISE SPECIFIED:
- DIMENSIONS IN INCHES
VARIOUS
MATERIAL:
- ALL DIMENSIONS PRIOR TO FINISHING
human. Use only for moving non-human loads.
- REMOVE ALL BURRS AND BREAK SHARP
-
FINISH:
EDGES WITH 0.010 MAX RADIUS OR
CHAMFER
© The designs, constructions, arrangements, disclosures and devices
2. COMPATIBILITY
illustrated in presentations bearing this note are the property of Harken, Inc,
TOLERANCES UNLESS OTHERWISE SPECIFIED:
Pewaukee, WI and are submitted in confidence with the understanding
-
DECIMAL: that such material shall not be utilized in any way by any party without prior
SURFACE FINISH: -
- Always verify the Wingman MH is compatible with the other components of your
-
ANGULAR:
system.
- Any equipment used with the pulleys (such as anchors and locking connectors)
must conform to applicable standards and/or regulations.
3. SAFETY
-
In the event that the Wingman MH is shock-loaded, it must be removed from
service and destroyed.
4. INSPECTION
- Verify all pieces of equipment in the system are in good working condition and the
product is correctly positioned while in use. Check the condition of the product
before and after each use. Remove from service if there is any doubt about safety
and serviceability.
- Visually and by touch, inspect pulley for cracks, distortion, corrosion, scratches,
gouges, sharp edges, or rough areas that might abrade a rope, or alter the normal
rotation of the sheave(s) or the normal action of the release handle.
- Verify the sheaves turn freely.
- Verify all markings and labels are present and legible.
- An in-depth inspection must be carried out at least every 12 months and more
frequently if the pulley is in frequent and intense use.
5. OPERATION
Function test - Before each use, verify the device is working properly. Connect one
-
end of the Wingman MH to an anchor with a shackle, apply a load to the other end,
and verify the rope is locked at the cam block. Grip the haul/tail end of the rope with
one hand and gently open the release handle with the other hand, allowing the rope
to pass through the cam block and lower the load. Gradually close the release handle
and verify the rope is locked by the cam block. With a moderate load on the system,
262-691-3320
harken.com
infoUSA@harkenindustrial.com
FOR PROTOTYPING PURPOSES ONLY
DOUBLE BECKET BLOCK
DIMENSIONS IN OVALS ARE KEY
PRODUCT CHARACTERISTICS
UNLESS OTHERWISE SPECIFIED:
- DIMENSIONS IN INCHES
VARIOUS
MATERIAL:
-
FINISH:
CHAMFER
© The designs, constructions, arrangements, disclosures and devices
illustrated in presentations bearing this note are the property of Harken, Inc,
Pewaukee, WI and are submitted in confidence with the understanding
-
that such material shall not be utilized in any way by any party without prior
SURFACE FINISH: -
-
FOR PROTOTYPING PURPOSES ONLY
DOUBLE BECKET BLOCK
LOAD TENDER
written consent from Harken, Inc.
PRODUCT MANUAL
WORKING LOAD LIMIT: 675 LBS
ROPE DIAMETER: 8 MM FIBER [5/16"]
(replace rope only with Harken authorized replacement rope)
Please read these instructions carefully
before installing, servicing, or operating
the equipment. This manual may be
modified without notice. In the event this
manual is translated, the English version
is definitive. For the latest manual
revision, go to www.harken.com, click
Safety & Rescue, then product support.
PLEASE SAVE THESE INSTRUCTIONS
Cam (or Silver) Block:
MH
Release Direction
FOR MATERIAL
HANDLING ONLY
DO NOT
REPLACE ROPE
Product Number
HARKEN INC.
Intended Use
FOR QUOTATION PURPOSES ONLY
Manufacturer
Serial Number DRAWING NUMBER
DIMENSIONS IN OVALS ARE KEY
PRODUCT CHARACTERISTICS
LOAD TENDER
open the release handle and release it. Verify the release handle snaps closed. Pull
UNLESS OTHERWISE SPECIFIED:
INCORPORATED - DIMENSIONS IN INCHES
PART #
- ALL DIMENSIONS PRIOR TO FINISHING
on the haul/tail end of the rope and verify the sheaves turn freely and you hear a
- REMOVE ALL BURRS AND BREAK SHARP
N15 W24983 Bluemound Road
SHEET NUMBER:
EDGES WITH 0.010 MAX RADIUS OR
Pewaukee, Wisconsin 53072
DESIGN BY :
clicking sound.
Tel: 262-691-3320
TOLERANCES UNLESS OTHERWISE SPECIFIED:
DRAWN BY :
Fax: 262-691-3807
DECIMAL:
ENG. APR :
www.harken.com
- Lowering - To lower a load, carefully open the release handle while securely
written consent from Harken, Inc.
ANGULAR: MFG. APR :
tailing the haul/tail end of the rope. Control the speed of descent by a
combination of modulating the release handle and hand grip on the rope. To stop
lowering, gradually close the release handle until the cam block locks the rope.
DRAWING NUMBER REV.
Releasing the handle completely will immediately stop the lowering action.
H-86666
0
Remote Release - To use the remote release, tie a stopper knot in the end of the
-
INCORPORATED INCORPORATED
-
PART #
remote release cord. Thread the other end through the hole in the release handle.
1/1 1:1
SHEET NUMBER: SCALE:
JDM 9/9/2021
DESIGN BY : DATE:
Connect the Wingman MH to an anchor using a shackle, then connect the other end
DRAWN BY : ORLY DATE: 9/10/2021
to the load. Thread the remote release cord through the upper shackle. While firmly
CJL 9/24/2021
DATE:
ENG. APR :
MGK 10/15/2021
MFG. APR : DATE:
gripping the haul/tail end of the rope, pull on the remote release cord to actuate the
release handle. Using both hands on the rope while simultaneously actuating the
release handle, gradually relax your grip on the rope so that it begins to slide through
your hands. Modulate the descent speed of the load by a combination of adjusting
your grip on the rope and moving the remote release cord up or down.
NOTE: Keeping the same hand on both the rope and the cord ensures that if your
hand travels closer to the anchor point the remote release eases and the lowering
stops.
Hold the remote release handle and haul/tail end of the rope together to control the
rate of descent. To stop lowering, ease pressure on the handle to close and lock it.
Releasing the handle completely immediately stops the lowering action. Limit the load
to 300 lbs when using remote release.
EXAMPLE:
WINGMAN MH
(Material Handling)
Part Number: IN172.3m
Manufacturer
Country of
Manufacture
Rope Diameter
FOR PROTOTYPING PURPOSES ONLY
REV.
DOUBLE BECKET BLOCK
H-86666
0
LOAD TENDER
- VARIOUS
MATERIAL:
1/1 1:1 -
FINISH:
SCALE:
CHAMFER
JDM 9/9/2021
DATE: © The designs, constructions, arrangements, disclosures and devices
illustrated in presentations bearing this note are the property of Harken, Inc,
ORLY 9/10/2021
DATE:
Pewaukee, WI and are submitted in confidence with the understanding
- CJL 9/24/2021
DATE: that such material shall not be utilized in any way by any party without prior
SURFACE FINISH: -
written consent from Harken, Inc.
- MGK 10/15/2021
DATE:
PRODUCT CHARACTERISTICS PRODUCT CHARACTERISTICS
- DIMENSIONS IN INCHES - DIMENSIONS IN INCHES
- ALL DIMENSIONS PRIOR TO FINISHING - ALL DIMENSIONS PRIOR TO FINISHING
- REMOVE ALL BURRS AND BREAK SHARP - REMOVE ALL BURRS AND BREAK SHARP
EDGES WITH 0.010 MAX RADIUS OR EDGES WITH 0.010 MAX RADIUS OR
CHAMFER CHAMFER
- -
- -
- -
Red Block
Rope
Cam (or Silver) Block
Product Brand
Release Handle
DRAWING NUMBER
H-86666
-
PART #
1/1
SHEET NUMBER:
JDM
DESIGN BY :
ORLY
DRAWN BY :
CJL
ENG. APR :
MGK
MFG. APR :
LOAD TENDER LOAD TENDER
INCORPORATED INCORPORATED INCORPORATED
VARIOUS VARIOUS
- -
Release Handle
Remote
Release
Cord
Shackle
REV.
0
1:1
SCALE:
DATE: 9/9/2021
9/10/2021
DATE:
9/24/2021
DATE:
10/15/2021
DATE:
DRAWING NU DRAWING NU
P P P
- -
- ALL D - ALL D - ALL D
- REMOV - REMOV - REMOV
EDGE EDGE EDGE