Table of Contents
Advertisement
Quick Links
ASSEMBLY INSTRUCTIONS
GSL-S SERIES | THE GREYSTONE SOUND LECTERN
ASSEMBLY MANUAL
Dear Customer, Thank you for your purchase. Although extreme care goes into manufacturing & packaging of this product,
mistakes are possible. If you encounter any missing parts or di culty in assembly, please contact our customer service
Toll Free at 1-800-261-4112 or info@nationalpublicseating.com for courteous & immediate resolution to your problem.
Page 1 of 10
www.nationalpublicseating.com
1-800-261-4112
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for National Public Seating Oklahoma Sound GSL-S Series
Summary of Contents for National Public Seating Oklahoma Sound GSL-S Series
- Page 1 ASSEMBLY INSTRUCTIONS GSL-S SERIES | THE GREYSTONE SOUND LECTERN ASSEMBLY MANUAL Dear Customer, Thank you for your purchase. Although extreme care goes into manufacturing & packaging of this product, mistakes are possible. If you encounter any missing parts or di culty in assembly, please contact our customer service Toll Free at 1-800-261-4112 or info@nationalpublicseating.com for courteous &...
-
Page 2: Technical Specifications
TECHNICAL SPECIFICATIONS Power Output ..50W RMS at 10% THD Power Supply..110-120V ohms DC 10.8 12V Mic......Elect Condenser Mic (2) Fuse......2A normal Aux......150 mV 220k Output.....8 ohms Frequency....100HZ-25KHZ Accessories....Handheld Mic, Clip-On-Mic; Response....+ 3dB Gooseneck; Shock mount Mic Holder. ASSEMBLY TIPS • Do not use a sharp instrument such as a Knife or Screwdriver to open the packaging, as this may scratch or possibly damage the unit. -
Page 3: Cabinet Parts
CABINET PARTS Right Left Back Panel x1 Front Panel x1 Lectern Top x1 Shelf x3 Panel x1 Panel x1 Door x1 Door x1 Foam Strip x1 Keyboard x1 Right Side Shelf x1 Locking Casters x2 Left Side Shelf x1 Support Bracket x1 Support Bracket x1 Non-Locking x2 CASTER INSTALLATION... - Page 4 ATTACHING BACK PANEL TO SIDE PANELS Lay Back Panel on a floor or flat surface. Take Side Panel and align holes on side to holes on tubes on right side of Panel . Install by using three Black 15mm Phillips Head Screws from Hardware Packet 3.
-
Page 5: Door Assembly & Installation
CABINET SHELF INSTALLATION Diagram 5 Place one Shelf at the bottom of Cabinet assuring that it is firmly resting on ledges of the interior of the side and back Panels of Cabinet. While holding on a slanted position, place the remaining middle Shelf on the ledges of side Panels assuring it is firmly... -
Page 6: Top Assembly & Installation
Using Silver Phillips Head Screws Diagram 8 Black Handles from Hardware Packet 1, install Door Knobs onto Panels & using a Philips Screwdriver Diagram 8 While holding Door , insert Pivot of bottom of Door into the hole Diagram 9 Diagram 10 located on left side of cabinet bottom. -
Page 7: Keyboard Installation
Using the four remaining four Phillips-Head Diagram 13 Rear Screws Black 10mm Screws from Hardware Package 3, secure cabinet to top by installing Screws through holes in metal strip at front of Cabinet and at back through tabs located at top of posts. Diagram 13 Front Screws KEYBOARD INSTALLATION... -
Page 8: Amplifier Installation
AMPLIFIER INSTALLATION Diagram 17 Carefully remove Amplifier from the carton. Remove the Adhesive Backing from one side of the Foam Strip and apply it to the metal Speaker Wire cross brace located under the Keyboard tray. After Foam Strip is in place remove the Adhesive Backing from the other side. - Page 9 AMPLIFIER OPERATING INSTRUCTIONS OPERATING PRECAUTIONS Before operating the Amplifier, be sure you fully understand all instructions and features of the Amplifier. DO NOT turn Amplifier on until all input and output connections have been made. NEVER replace fuses unless power is o . MICROPHONE INPUT CONNECTION The Microphone input accepts 1/4”...
- Page 10 REMOVAL AND INSTALLATION OF AMPLIFIER If your Amplifier has to be removed for servicing follow these simple Steps: Disconnect A/C wall plug. Open the cabinet Doors and remove the two screws that go from the metal brace into the bottom of the Amplifier. Gently pry out the Amplifier beginning from the top portion.
Need help?
Do you have a question about the Oklahoma Sound GSL-S Series and is the answer not in the manual?
Questions and answers