Malmbergs 99 170 34 Instruction Manual

Trailing Edge Dimmer
Switch 300W LED
Brugsanvisning / Instruction Manual
Käyttöohje / Bruksanvisning
EMC Standard (EMC)
EN 60669-2-1:2004+A1:2009+A12:2010 (Clause 26)
EN 61000-3-2:2014
EN 61000-3-3:2013
Safety Standard (LVD)
EN 60669-2-1:2004 + A1:2009 + A12:2010
EN 60669-1:2018
RoHS Standard (RoHS)
Directive (EU) 2015/863 amending 2011/65/EU
DECLARATION OF CONFORMITy
We hereby certify that the device satisfies the provisions
for CE/Nemko markings in accordance with the EU
directives (LV Directive 2014/35/EU, EMC Directive
2014/30/EU, RoHS Directive (EU) 2015/863 amending
2011/65/EU) as described in this manual.
For and on behalf of:
Malmbergs Elektriska AB, Sweden.
Mr. Magnus Johansson / Product Manager
Date: 02 July, 2019
Malmbergs Elektriska AB (publ)
PO Box 144, SE-692 23
Kumla, SWEDEN
Phone: +46 (0)19 58 77 00
info@malmbergs.com
www.malmbergs.com
99 170 34
DK
DREJE LySDæMPER, CR
Læs vejledningen inden start af installation og
giv vejledningen til brugeren når installationen
er færdig.
TEKNISKE DATA
Mærkespænding
Frekvens
Max. belastning
Min. belastning
Lysdæmper type
Styring
Dæmpbare LED Lyskilder
12V halogen med elek-
tronisk trafo
Glødelamper / 230V
halogen lamper
ANVENDELSE
• Kan anvendes i både nye og gamle installationer.
• Indbygget overbelastningsbeskyttelse.
INSTALLATION
• Sørg altid for at strømmen er afbrudt under installati-
ons arbejdet. Forbind lysdæmperen efter forbindelses
skemaet.
• Når installationen er udført, tændes strømmen. Tænd
for de tilsluttede lamper. Drej lysdæmperen helt mod
venstre og indstil min. niveau på min. skruen på
lysdæmperen. Ved at indstille min. undgås flimmer
DK
og det sikres at den tilsluttede lyskilde tænder i min.
EN
niveau.
FI
NO
SE
Forbindelses skema
Lysdæmper alene
Lysdæmper i korrespondance
OBS:
• Installation skal udføres af elektriker, og nationale
regler skal følges.
• Installationen skal udføres uden spænding.
• Forbind ikke flere lysdæmpere til samme belastning.
EN
TRAILING EDGE DIMMER SWITCH, RC
Read these instructions before starting the
installation and hand it over to the user when
finished.
TECHNICAL DATA
220-240V ~
Operating voltage
50Hz
Frequency
400W
Maximum load
5W
Minimum load
Bagkant CR
Dimming type
1 Pol / Korr.
Control method
5-300W
Dimmable LED lamps
12V halogen lighting with
5-500VA/W
electronic transformers
Incandescent lighting,
5-500VA/W
230V halogen lamps
FEATURES
• Suitable for both retrofit and new installations.
• Built-in overheating protection.
INSTALLATION
• Always make sure that the electricity is switched off
during the installation. Then connect the power wires
as indicated in the wiring diagram below.
• Switch on the electricity again. Turn on the connected
lamps. Now turn the dimmer knob all the way to the
left and set the minimum light with the MIN. screw
on the dimmer. you can adjust this with a screwdriver.
Adjust the lamps so that they do not flicker.
Wiring Diagram
1 Gang
1 Gang, 2 Way
Please note:
• The installation must be carried out by a qualified
electrician, taking into account the national rules.
• Make sure that the electricity is switched off during
installation.
• you cannot connect more than one dimmer in parallel
to operate the same charge from two points.
220-240V ~
50Hz
400W
5W
Trailing Edge
1 Gang / 2 Way
5-300W
5-500VA/W
5-500VA/W