Download Print this page
Dometic FRONT RUNNER PBFF001 Installation Instruction

Dometic FRONT RUNNER PBFF001 Installation Instruction

Ford f150 crew cab pro bed rack mounting system

Advertisement

Quick Links

front runner
START HERE!
Don't be a hero and muscle through this installation without reading these fitting instructions first! Improper installation of this gear may void certain
aspects of your warranty.
Before you begin, take a moment and open all your Front Runner Rack Kit boxes and gather the assembly instructions for the various components.
A complete kit will contain:
1. Front Runner Mounting System specific to your vehicle
2. Front Runner Rack Tray or Load Bar Slats
This document will guide you through the assembly of the Mounting System and assist you in fitting the Rack tray or Load Bars to your specific vehicle.
Please refer to the next page for a list of all the components, quantities and tools required.
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
PBFF001_REV_A00
Ford F150 Crew Cab Pro Bed Rack
Mounting System
READ ME FIRST
IMPORTANT WARNING!
Please call us if you have any questions about the installation of this product.
1
PBFF001
© 2023 FRONT RUNNER VEHICLE OUTFITTERS
ENG

Advertisement

loading
Need help?

Need help?

Do you have a question about the FRONT RUNNER PBFF001 and is the answer not in the manual?

Questions and answers

Summary of Contents for Dometic FRONT RUNNER PBFF001

  • Page 1 Ford F150 Crew Cab Pro Bed Rack front runner Mounting System PBFF001 START HERE! READ ME FIRST Don’t be a hero and muscle through this installation without reading these fitting instructions first! Improper installation of this gear may void certain aspects of your warranty.
  • Page 2 CHECK ONLINE FOR LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM GET ORGANIZED TOOLS NEEDED IN THE BOX PBFF001 REAR MOUNTING BRACKET 10mm FRONT MOUNTING BRACKET 13mm 11.5mm REAR GUSSET FRONT GUSSET 12 X M8 X 16 X 1.6 FLAT WASHER 12 X M8 X 30 HEX BOLT 12 X M8 PLUS NUT 12 X...
  • Page 3 CHECK ONLINE FOR LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM GET ORGANIZED IN THE BOX PBRA001 IN THE BOX PBRA001 PRO BED RACK LEG M6 x 12 BUTTON HEAD SCREW PRO BED RACK REAR BRACE FRONT HORIZONTAL BRACE PRO BED RACK RH REAR WING BRACKET FRONT CENTER BRACE PRO BED RACK TOP TRUSS M6 x 20 BUTTON HEAD SCREW...
  • Page 4 CHECK ONLINE FOR THE LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM GET ORGANIZED IN THE BOX PBAL_1450 TOOLS NEEDED TOP EXTRUSION TOP MIDDLE EXTRUSION BOTTOM EXTRUSION Friend 1450mm PSA STRIP PE60 PBFF001_REV_A00 © 2023 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 5 FIT AND SECURE Place the front mounting brackets (LH shown) on the bed top ledge. Mark the 3 mounting holes per side. Use a 4mm bit and drill a pilot hole before opening to 11.5mm. Insert a Plus Nut (Item 7) into the holes drilled in 2.1.
  • Page 6 FIT AND SECURE TOP EXTRUSION Take note of extrusion orientation ! Torx Using the supplied T30 6" torx bit and a cordless driver fit the extrusion using the M6x25 thread forming screws (Item 19).Use a slow and constant speed when using the cordless driver.
  • Page 7 FIT AND SECURE Fit the Rear Brace (Item 2) using the M6x12 button head screws and M6 Nyloc nuts (Item 14 & 8). Fully tighten and place M6 Nut caps (Item 9) 13mm on the M6 Nyloc Nuts Tightening Torque: M8 : 15-20Nm / 11.06 ft lb - 14.75 ft lb Loosely assemble the rear top truss using the M8x20 Button head screws, M8x19x2 Flat...
  • Page 8 FIT AND SECURE 2.10 Assemble the Rear Wing Brackets (Item 3) using the M6x12 Button head screws and M6 Nyloc Nuts (Item 14 & 8). Place the M6 Nut caps (Item 9) over the nyloc 10mm nuts. 13mm Tightening Torque: M6 : 8-10Nm / 5.9 ft lb - 7.38 ft lb 2.11 With the Pro Bed Rack sub assembled and with...
  • Page 9 FIT AND SECURE Fully tighten all the bolts and nuts and place 2.10 nut caps where needed. 10mm COMPLETION Congratulations! You did it. Take a step back and admire your work! INSTALL OTHER VEHICLE AND RACK ACCESSORIES Now's the time to visit your favorite Front Runner dealer in person or online. IMPORTANT! FRONT RUNNER RACK KITS OFTEN HAVE A HIGHER LOAD RATING THAN THE VEHICLES THEY ARE MOUNTED TO.

This manual is also suitable for:

Front runner pbff001sFront runner pbff001t