Kaisai MONO KHC-06RY1-B Installation Manual
  1. Manuals
  2. Brands
  3. Kaisai Manuals
  4. Heat Pump
  5. MONO KHC-06RY1-B
  6. Installation manual

Kaisai MONO KHC-06RY1-B Installation Manual

Heat pump outdoor unit
Hide thumbs Also See for MONO KHC-06RY1-B:

Advertisement

Table of Contents

HEAT PUMP
HEAT PUMP
MONO
MONO
KHC-06RY1-B KHC-12RY3-B
KHC-08RY3-B KHC-14RY3-B
KHC-10RY3-B KHC-16RY3-B
Instalation Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MONO KHC-06RY1-B and is the answer not in the manual?

Questions and answers

Related Manuals for Kaisai MONO KHC-06RY1-B

Summary of Contents for Kaisai MONO KHC-06RY1-B

  • Page 1 HEAT PUMP HEAT PUMP MONO MONO KHC-06RY1-B KHC-12RY3-B KHC-08RY3-B KHC-14RY3-B KHC-10RY3-B KHC-16RY3-B Instalation Manual...
  • Page 2 CONTENTS...
  • Page 6 ： ： ：...
  • Page 8 ℃ ℃ ℃ ℃ （ ）...
  • Page 13 (unit: mm) 10 Expansion bolt Rubber shocking proof mat Solid ground Concrete or roofing basement 00mm...
  • Page 17 ） ）...
  • Page 19 ）...
  • Page 21 ： （ ）...
  • Page 22 Tank booster heater...
  • Page 28 ， ，...
  • Page 30 ，...
  • Page 34 ：...
  • Page 36 9.4.3 Water circuit connection Water connections must be made correctly in 9.4.4 Water circuit anti-freeze protection accordance with labels on the outdoor unit, with respect to the water inlet and water outlet. All internal hydronic parts are insulated to reduce heat loss.
  • Page 41 ， ，...
  • Page 42 （ ）...
  • Page 43 ，...
  • Page 44 Slave unit Master unit Please use the shielded wire, and the shield layer must be grounded..Master unit Slave unit 1 Slave unit 2 Slave unit x Only the last IDU requires adding the build-out resistor at H1 and H2. Fuse Fuse Fuse...
  • Page 46 ： ：...
  • Page 47 、...
  • Page 48 （ ） （ ） （ ） ： （ ） ： （ ）...
  • Page 49 （ ） （ ） （ ） （ ） ： （ ） ： （ ） （ ）...
  • Page 50 ： ：...
  • Page 53 ： ： ： ： ： ： ： ： ： ： ：...
  • Page 55 10.5 Field settings The unit should be configured to match the installation environment (outdoor climate, installed options, etc.) and user demand. A number of field settings are available. These settings are accessible and programmable through “FOR SERVICEMAN” in user interface. Powering on the unit When power on the unit, "1%~99%"...

  • Page 56: Dhw Mode Setting

    About FOR SERVICEMAN 10.5.1 DHW MODE SETTING DHW = domestic hot water "FOR SERVICEMAN" is designed for the installer to set the parameters. Go to > FOR SERVICEMAN> 1.DHW MODE SETTING. Press . The following pages will be Setting the composition of equipment. displayed: Setting the parameters.

  • Page 57: Heat Mode Setting

    10.5.5 TEMP. TYPE SETTING 2 COOL MODE SETTING About TEMP. TYPE SETTING 2.1 COOL MODE 2.2 t_T4_FRESH_C 2.0HRS The TEMP. TYPE SETTING is used for selecting whether 2.3 T4CMAX 43°C the water flow temperature or room temperature is used 2.4 T4CMIN 20°C to control the ON/OFF of the heat pump.

  • Page 58: Holiday Away Setting

    10.5.7 Other HEATING SOURCE In this case, the setting value of zone 1 is T1S,the setting value of zone 2 is T1S2. The OTHER HEATING SOURCE is used to set the parameters of the backup heater, additional heating If you set DOUBLE ZONE and ROOM TEMP. to YES, sources and solar energy kit.

  • Page 59: Restore Factory Settings

    9 SERVICE CALL If YES is selected, the following pages will be displayed: PHONE NO. *************** MOBILE NO. ****************** 11 TEST RUN 11.1 POINT CHECK 11.2 AIR PURGE 11.3 CIRCULATED PUMP RUNNING CONFIRM ADJUST 11.4 COOL MODE RUNNING 11.5 HEAT MODE RUNNING The number displayed on the user interface is the phone ENTER number of your local dealer.

  • Page 60: Special Function

    When in air purge mode, SV1 will open, SV2 will close. During HEAT MODE test running, the default target outlet 60s later the pump in the unit (PUMPI) will operate for water temperature is 35°C. The IBH (internal backup 10min during which the flow switch will not work. After the heater) will turn on after the compressor runs for 10 min.
  • Page 61 Go to > FOR SERVICEMAN> 12.SPECIAL During preheating for floor, all the buttons except FUNCTION. invalid. If you want to turn off the preheating for floor, please press Before floor heating, if a large amount of water remains on the floor, the floor may be warped or even rupture during The following page will be displayed: floor heating operation, in order to protect the floor, floor drying is necessary, during which the temperature of the...

  • Page 62: Auto Restart

    10.5.15 INPUT DEFINE 12.3 FLOOR DRYING UP The unit will operate floor dryind up How to set the INPUT DEFINE on 09:00 01-08-2018. Go to > FOR SERVICEMAN> 15.INPUT DEFINE 15 INPUT DEFINE 15.1 M1M2 REMOTE 15.2 SMART GRID 15.3 Tw2 CONFIRM 15.4 Tbt1 to scroll the cursor to YES and press...
  • Page 69 、 、...
  • Page 70 ℃...
  • Page 72 ， ＜...
  • Page 75 ＜...
  • Page 78 、 、 、 、...
  • Page 85 16125300002999 V.H...
  • Page 88 kaisai.com...

This manual is also suitable for:

Mono khc-12ry3-bMono khc-08ry3-bMono khc-14ry3-bMono khc-10ry3-bMono khc-16ry3-b

Table of Contents