Page 1 INSTALLATION MANUAL...
Page 2 Where modern design meets timeless beauty, Amani arises. A vision of serenity and harmony, born from passion and precision.
Page 3: Table Of Contents
INTRODUCTION 2.3 • Monitoring and securing frame profiles ............. 48 ....................6 2.4 • Fastening of feed and discharge hopper........... 49 1 • Amani general .......................7 2.4.1 • L-junction with column ..............49 2.4.2 • L-junction without column .............. 49 1.1 •...
Page 4 5.2 • Lineo Heat ....................139 4.1.3 • Joining knife bracket ............... 101 5.2.1 - Position the Amani drill jig on the high pivot side ......139 4.2 • If iconic LED line: prepare wiring .............. 103 5.2.2 - Position the jig on the low pivot side..........141 4.2.1 •...
Page 5 Amani ® 8.5 • Installation of the door frames ..............201 12.3 • Connecting spotlights to control unit ............. 278 8.6 • Installation of the support posts on the door frames ......204 12.4 • Use the tool to remove the cable from the rail ........281 8.7 •...
Page 6: Introduction
Amani ® INTRODUCTION...
Page 7: Amani General
1.1 • Introduction Renson Amani ® First read this manual carefully before you begin. The installation of the RENSON Amani should be done by a specialist. ® RENSON reserves the right to make technical changes to its products without prior notice.
Page 8: Electrical Connections
• Do not place fingers in a lateral guide while the screen covering is moving. • Faulty installations or irregularities in the installation could have serious consequences when using the product. • Only use the components delivered by the RENSON company with your product; otherwise, the guarantee terms and conditions could be nullified.
Page 9: Installation Types & Dimensions
Amani ® 1.3 • Installation types & dimensions 1.3.1 • Single building types Freestanding - single Façade-mounted Span - single Façade-mounted Pivot - single Façade mounted Pivot AND Span - single 1.3.2 • Joined on the pivot side Freestanding - 2-piece Façade-mounted Span - 2-piece...
Page 10: Joined On The Span Side
Amani ® 1.3.3 • Joined on the span side Freestanding - 2-piece Façade-mounted Span - 2-piece Façade-mounted Pivot - 2-piece Freestanding - 3-piece Façade-mounted Span - 3-piece Façade-mounted Pivot - 3-piece 1.3.4 • Facade mounted with partial wall Façade mounted Pivot AND Span with partial wall...
Page 11 Amani ® PH = passage height TH = total height S = span (depth) P = pivot (width) OL = overlength...
Page 12: Technical Information
® 1.4 • Technical information 1.4.1 • Motor position MOTOR With Amani, the motor of the bladed roof is always 30 mm provided on the lowest pivot side (so this is different from Camargue). Having the motor on the lowest side ensures it remains easily accessible when the cover is wall-mounted.
Page 13: Base Plates
Amani ® 1.4.2 • Base plates Invisible base plate Visible base plate Visible base plate - corner...
Page 14 Amani ® Fixing base plate to the column Invisible base plate Visible base plate SET: SAP 7133 SET: SAP 7133 SAP 6832 SAP 6832 LOCTITE DIN 7991 LOCTITE DIN 7991 M12x50 M12x50 Visible base plate - corner SET: SAP 7133...
Page 15: Junctions
The possible building types are realised using 3 different types of junction. A junction is a corner where frame profiles (span and pivot) are connected. This overview describes all the connections that are possible with the Amani. L-junction without column...
Page 16 Amani ® L-junction T-junction I-junction 2 beams come together (indicated in drawing on 3 beams come together. A T-junction is a mechanical A beam is partially interrupted by an intermediate or previous page) connection of 3 frame profiles - two span profiles shifted column.
Page 17: Water Drainage And Water Transit
Amani ® 1.4.4 • Water drainage and water transit 1.4.4.1 • In the junctions Water drainage Water transit channel 1.4.4.2 • In the beams No water flow No water Pas de passage flow d’eau...
Page 18 Amani ® Span to the wall Closed node Motor Water drainage direction (low side) Water drainage direction (high side) Column No column...
Page 19 Amani ® Pivot to the wall Closed node Motor Water drainage direction (low side) Water drainage direction (high side) Column No column...
Page 20 Amani ® 1.4.4.3 • In the columns Sideways water drainage Downward water drainage Cut the drain pipe...
Page 21: Orientation Of Structure
Amani ® 1.4.5 • Orientation of structure...
Page 22: Packaging
Open the crates as soon as you need them according to the order in the manual. For this, check the label on the box to see which part it contains. These parts are always in a separate box: • fieldbox electronics Amani = electronic components • fieldbox components Amani = screws • fieldbox components Amani = small coated components...
Page 23: Construction
Amani ® CONSTRUCTION...
Page 24: Basic Construction
2.1 • Freestanding type Please refer to the drawing accompanying your order for the correct dimensions. 2.1.1 • Determine the position of the base plates Determine the position of the Amani and mark the Pivot & the Span. ® Mark where the mounting base(s) will be placed based on the type of base plates and construction.
Page 25: L-Junction With Column (Pivot)
Amani ® 2.1.2 • L-junction with column (pivot) PIVOT...
Page 26 Amani ® SET: SAP 7040 (bladed roof) SAP 7042 (fixed roof) SET: SAP 7040 (bladed SAP 6708 roof) DIN 912 M8x25 SAP 7042 (fixed roof) SAP 6708 DIN 912 M8x25...
Page 27: L-Junction With Column (Span)
Amani ® 2.1.3 • L-junction with column (span) SPAN...
Page 28 Amani ® SET: SAP 7040 (bladed roof) SAP 7042 (fixed roof) SET: SAP 6708 SAP 7040 (bladed DIN 912 M8x25 roof) SAP 7042 (fixed roof) SAP 6708 DIN 912 M8x25...
Page 29: I-Junction With Column
Amani ® 2.1.4 • I-junction with column SET: SAP 7058 SAP 6708 DIN 912 M8x25...
Page 30: L-Junction Without Column
Amani ® 2.1.5 • L-junction without column SET: SET: SAP 7040 (bladed SAP 7040 (bladed roof) roof) SAP 7042 (fixed roof) SAP 7042 (fixed roof) SAP 6708 SAP 6708 DIN 912 M8x25 DIN 912 M8x25...
Page 31 Amani ® SET: SAP 7040 (bladed roof) SAP 7042 (fixed roof) SAP 6708 DIN 912 M8x25...
Page 32 Amani ® SET: SAP 7040 (bladed roof) SAP 7042 (fixed roof) SAP 6708 DIN 912 M8x25...
Page 33: T-Junction With Column (Linked Roof Section)
Amani ® 2.1.6 • T-junction with column (linked roof section) Linked span Linked pivot Position of the VISIBLE base plates (270 x 270 mm) Positie van de ZICHTBARE voetplaten (270 x 270 mm) Position of the VISIBLE base plates (270 x 270 mm)
Page 34 Amani ® 2.1.6.1 • Linked span SET: SAP 7040 (bladed roof) SAP 7042 (fixed roof) Both sides SAP 6708 DIN 912 M8x25...
Page 35 Amani ® SET: SAP 7057 SET: SAP 7057 SAP 6998 SAP 6998 DIN 912 DIN 912 M8x50 M8x50 Seal the opening with the supplied tape.
Page 36 Amani ® 2.1.6.2 • Linked pivot SET: SAP 7040 (bladed roof) SAP 7042 (fixed roof) SAP 6708 DIN 912 M8x25...
Page 37 Amani ® SET: SAP 7057 SET: SAP 7057 SAP 6998 SAP 6998 DIN 912 DIN 912 M8x50 M8x50 Seal the opening with the supplied tape.
Page 38: Wall-Mounted
2.2 • Wall-mounted Please refer to the drawing accompanying your order for the correct dimensions. Installation of the wall profile (only for wall-mounted construction types) Determine the position of the Amani and mark the Pivot & the Span. ® PIVOT...
Page 39 Amani ® Determine the position of the wall profile and mark it on both sides of the wall. Top wall profile should be placed at the following height: passage height (PH) + 225 mm. Precautionary measure 60 mm Internal wall...
Page 40 Amani ® SAP 7075 SPAN / PIVOT Use screws adapted to the underlying structure (to be provided by the installer).
Page 41 Amani ®...
Page 42 Amani ® SET: SAP 7040 (bladed roof) Both sides SAP 7042 (fixed roof) SET: SAP 7040 (bladed SAP 6708 roof) DIN 912 M8x25 SAP 7042 (fixed roof) SAP 6708 DIN 912 M8x25 Fix the wall profile to the wall for now. Use some of the slots on the wall profile to do this. The required screws are not included.
Page 43 Amani ® Mark off and place the anchor in the wall (on both sides). Anchor points are pre-drilled in the wall profile. Fixings and fasteners are not supplied. To be determined by the customer. depending on the supporting structure. Both sides...
Page 44 Amani ® If multiple roof elements are placed against the wall, steps 1 to 5 are repeated for each element. To fix the other beams against the wall, the bolts can be secured to the end cap more easily through the top side.
Page 45 Amani ® SET: SAP 7040 (bladed roof) SAP 7042 (fixed roof) SAP 6708 DIN 912 M8x25 SET: SAP 7040 (bladed roof) SAP 7042 (fixed roof) SAP 6708 DIN 912 M8x25...
Page 46 Amani ® SET: SAP 7040 (bladed roof) SAP 7042 (fixed roof) SAP 6708 DIN 912 M8x25 SET: SAP 7040 (bladed roof) SAP 7042 (fixed roof) SAP 6708 DIN 912 M8x25...
Page 47 Amani ® SET: SAP 7040 (bladed roof) SAP 7042 (fixed roof) SAP 6708 DIN 912 M8x25 SET: SAP 7040 (bladed roof) SAP 7042 (fixed roof) SAP 6708 DIN 912 M8x25...
Page 48: Monitoring And Securing Frame Profiles
Amani ® 2.3 • Monitoring and securing frame profiles 90° 90° 90° 90° 90° 90° 90° 90° Secure the mounting bases. Use fasteners adapted to the relevant surface (to be provided by the installer). The position can still be corrected at this stage.
Page 49: Fastening Of Feed And Discharge Hopper
Amani ® 2.4 • Fastening of feed and discharge hopper 2.4.1 • L-junction with column 2.4.2 • L-junction without column SET: SET: SAP 7040 (bladed SAP 7040 (bladed roof) roof) SAP 7042 (fixed roof) SAP 7042 (fixed roof) SAP 1630...
Page 50: T-Junction With Column (Linked Roof Section)
Amani ® 2.4.4 • T-junction with column (linked roof section) SET: SAP 7040 (bladed roof) SAP 7042 (fixed roof) SAP 1630 DIN 912 M6x180...
Page 51: Sealing The Gutter End Caps
Amani ® 2.5 • Sealing the gutter end caps ± 2 min...
Page 52 Amani ® ± 2 min...
Page 53 Amani ®...
Page 54: Water Test 1: Checking The Gutter System
Amani ® 2.6 • Water test 1: checking the gutter system We recommend testing every installation for water infiltration prior to delivering. This can be done in a number of steps. These steps can also be used to help diagnose any water infiltration.
Page 55: Sealing Inside Corner Between Span And Pivot
Amani ® 2.7 • Sealing inside corner between span and pivot...
Page 56: Installation Of Column Cover And
Amani ® Install FIXSCREEN POWER SOCKET before fitting column covers and front covers. 2.8 • Installation of column cover and front cover 2.8.1 • L-junction with column CLICK CLICK CLICK CLICK...
Page 57 Amani ® CLICK CLICK CLICK CLICK CLICK CLICK CLICK CLICK CLICK...
Page 58: I-Junction With Column
Amani ® 2.8.2 • I-junction with column COVERS ARE SHORTER THAN THE FRONT WITH L-JUNCTION CLICK CLICK CLICK CLICK CLICK CLICK...
Page 59: L-Junction With Column At A Recessed
Amani ® 2.8.3 • L-junction with column at a recessed front cover CLICK CLICK CLICK CLICK CLICK CLICK...
Page 60: I-Junction With Column At A Recessed
Amani ® 2.8.4 • I-junction with column at a recessed front cover CLICK CLICK Outside Inside CLICK...
Page 61 Amani ® CLICK Outside...
Page 62: Installation Of The Iconic Led Lighting
Amani ® 2.8.5 • Installation of the iconic LED lighting SET: SAP 7040 (bladed roof) SAP 7042 (fixed roof) SAP 6708 DIN 912 M8x25...
Page 63 Amani ® LED module corner piece of the LED LED module diffuser corner piece of the LED...
Page 64 Amani ® POWER IO RECEIVER SUPPLY 230V...
Page 65: L-Junction Without Column
Amani ® 2.8.6 • L-junction without column 4 mm TIGHTEN 2-3 TURNS FULLY CLICK CLICK...
Page 66: Base Cover Plate At L-Junction Without Column
Amani ® 2.8.7 • Base cover plate at L-junction without column 150x150 150x127 127x127 150x144 150x121 L-junction L-junction L-junction L-junction against wall L-junction against wall 2x standard front cover 1x standard front cover 2x recessed front cover standard front cover...
Page 67: Upvc Finish Extraction
Amani ® 2.8.8 • UPVC finish extraction...
Page 68: Construction Of The Roof
Amani ® Install THE FIXED WALLS before securing the roof. 3 • Construction of the roof 3.1 • Bladed roof SET: SAP 7040 SET: SAP 7040 SAP 957 SAP 957 DIN912 DIN912 M4x10 M4x10...
Page 69 Amani ®...
Page 70: Fitting The Blades
Amani ® 3.1.1 • Fitting the blades Low side CLICK High side...
Page 71 Amani ® SET: SAP 7040 Low side...
Page 72: Fitting The Driving Profile And Drive Rod
Amani ® 3.1.2 • Fitting the driving profile and drive rod Low side SET: SAP 7040 Locking clips...
Page 73 Amani ®...
Page 74: Control For The Bladed Roof
Amani ® 3.2 • Control for the bladed roof 3.2.1 • Setting control for the bladed roof 0,5 sec. 230 V Check direction Only if direction is not correct The motor control and power supply are already Select the desired channel on the situo io hand-held Press the UP and DOWN buttons on the remote connected to the motor.
Page 75 Amani ® 0,5 sec. End position END POSITION CLOSE Close Snow position (Briefly) press the UP and DOWN button on the remote simultaneously. The blades will close completely and Close the blades until they return to a completely then automatically open completely (these are the end points.
Page 76: Changing The Frost/Snow Protection Function Via The Set&Go Installation Tool
Amani ® 3.2.2 • Changing the frost/snow protection function via the Set&Go installation tool Always connect 1 rain sensor per motor control. Rain sensors must not be interconnected. Always connect 1 rain sensor per motor control. Rain sensors must not be interconnected.
Page 77 Amani ® If your devices are already connected using a two-way remote Skip this step if no two-way remote is connected. (Nina, Tahoma), you can select this two-way remote. If you are not using a two-way remote, you will need to generate a temporary key.
Page 78 Amani ® Once back on the main menu, you will see a clear overview You can see the specifications for each device via the information button (‘i’ icon). of all devices found. These details consist of three pages (indicated at the bottom by 1/2/3).
Page 79 Don’t forget to confirm (2x) using the green button; if you do, the setting you selected will not be stored. Tip: – Frost position recommended by Renson: leave the blades open slightly (5 to 10°) to prevent them from freezing shut. – Snow position recommended by Renson: 90° vertical.
Page 80: Drive Fine Adjustment + Securing The Drive
Amani ® 3.2.3 • Drive fine adjustment + securing the drive The position of the blade drive is adjustable if the blades are under too much tension or are not closed completely after closing, You can adjust it using the motor-position fine adjustment, namely by moving the M10 nuts in the desired direction.
Page 81: Returning The Motor Control To Factory Settings
Amani ® 3.2.4 • Returning the motor control to factory settings Attention! When doing the reset below all other connected io-products on the same fus will also be reset! If necessary, disconnect the other connected products first (led, Fixscreen, heating).
Page 82: Fixed Roof
Amani ® 3.3 • Fixed roof 3.3.1 • Fitting the finishing profiles...
Page 83: Fitting The Canvas Profiles
Amani ® 3.3.2 • Fitting the canvas profiles SET: SAP 7042 SAP 2093 DIN7991 M8x45...
Page 84 Amani ® 1 x Pivot 1 x Pivot 2 x Span SLIDER Get the four canvas profiles. Fit each profile with a fabric strip with a zip. There is one fabric strip with a zip pin (PIN) and three fabric strips with zip box (BOX) and a zip slider (SLIDER).
Page 85: Fitting The Leaf Catchers
Amani ® 3.3.3 • Fitting the leaf catchers Low side High side...
Page 86: Fitting The Roof Plates
Amani ® 3.3.4 • Fitting the roof plates Low side High side Low side High side...
Page 87 Amani ® Low side High side...
Page 88 Amani ® SET: SAP 6355 SAP 2079 DIN7504 K 5,5x32...
Page 89 Amani ® Repeat steps 1 to 4...
Page 90: Finishing The Roof Plates
Amani ® 3.3.5 • Finishing the roof plates SET: SAP 6355 SAP 2079 DIN7504 K 5,5x32 SET: SAP 6355 SAP 2079 DIN7504 K 5,5x32...
Page 91: Fitting The Canvas
Amani ® 3.3.6 • Fitting the canvas CANVAS...
Page 92 Amani ®...
Page 93 Amani ® 5 mm You tighten these bolts roughly at the same time until the canvas fabric is nicely tensioned. Note: If you work with an electric screwdriver, it must have a force limited screw function. Never use the screwdriver in drill position to tighten the bolts. The...
Page 94 Amani ®...
Page 95: Awning
Amani ® First, install all cables needed for the electronic components in the canopy. Then also complete the installation of a FIXSCREEN, ROOF ACCESSORIES, FIXED WALLS GENERAL FINISHING before starting the installation of the canopy. 4 • Awning 1 = END KNIFE BRACKET...
Page 96 Amani ® When a fixed wall is combined with an awning, a lacquered plate (8139/SAP0002603) must be installed first.
Page 97: Inserting Knife Brackets
Amani ® 4.1 • Inserting knife brackets 4.1.1 • End knife bracket SET: SAP 5952 SAP 5807 DIN912 M8x35 SET: SAP 5952 SAP 1161 DIN913 M8x16 91°...
Page 98 Amani ® SET: SAP 5952 SAP 1168 DIN 7380 M8x12...
Page 99: Corner Knife Bracket
Amani ® 4.1.2 • Corner knife bracket SET: SAP 5953 SAP 5807 DIN912 M8x35 SET: SAP 5953 SAP 1161 DIN913 M8x16 SET: SAP 5953 SAP 5807 DIN912 M8x35 SET: SAP 5953 SAP 1161 DIN913 M8x16...
Page 100 Amani ® 91° SET: SAP 5953 SAP 1168 DIN 7380 M8x12...
Page 101: Joining Knife Bracket
Amani ® 4.1.3 • Joining knife bracket SET: SAP 5954* SAP 5955* SAP 5807 DIN912 M8x35 SET: SAP 5954* SAP 5955* SAP 1161 DIN913 M8x16 * SAP 5954: joining knife bracket pivot - SAP 5955: joining knife bracket span 91°...
Page 102 Amani ® SET: SAP 5954* SAP 5955* SAP 1168 DIN 7380 M8x12 * SAP 5954: joining knife bracket pivot - SAP 5955: joining knife bracket span...
Page 103: If Iconic Led Line: Prepare Wiring
Amani ® 4.2 • If iconic LED line: prepare wiring 4.2.1 • With end knife bracket 4.2.2 • With corner knife bracket POWER IO RECEIVER SUPPLY...
Page 104: Fit Cover (+ Cable Reducer If Iconic Led Line)
Amani ® 4.3 • Fit cover (+ cable reducer if iconic LED line) 4.3.1 • End knife bracket CLICK 4.3.2 • Corner knife bracket CLICK CLICK CLICK...
Page 105: Joining Knife Bracket
Amani ® 4.3.3 • Joining knife bracket CLICK CLICK...
Page 106: Installation Of Louvered Canopy Frame
Amani ® 4.4 • Installation of louvered canopy frame 4.4.1 • Installing side profiles of end knife brackets and corner knife brackets SETS* SAP 1240 BN1206 M8x10 * SAP 5952: end knife bracket - SAP 5953: corner knife bracket...
Page 107: Installing Profile At The Back Of Single Roof Sections
Amani ® 4.4.2 • Installing profile at the back of single roof sections SET: SAP 5952 (end knife bracket) PIVOT SAP 4122 DIN 7981 TX ST5,5x50 The recess is for the LED cable.
Page 108 Amani ® SPAN SET: SAP 5953 (corner knife bracket) SAP 4122 DIN 7981 TX ST5,5x50 SET: SAP 5953 (corner knife bracket) SAP 884 DIN 916 M8x6...
Page 109: Installing Profile At The Back Of Joined Roof Sections
Amani ® 4.4.3 • Installing profile at the back of joined roof sections SET: SAP 5954* SAP 5955* SAP 4587 DIN 7984 M6x16 * SAP 5954: joining knife bracket pivot - SAP 5955: joining knife bracket span...
Page 110: Installing The Side Profile Of The Joining Knife Bracket
Amani ® 4.4.4 • Installing the side profile of the joining knife bracket SETS* SAP 1240 BN1206 M8x10 * SAP 5954: joining knife bracket pivot - SAP 5955: joining knife bracket span...
Page 111: Fixing Side Profiles Of End Knife Brackets And Corner Knife Brackets
Amani ® 4.4.5 • Fixing side profiles of end knife brackets and corner knife brackets 100%...
Page 112: Installing Front Profiles
Amani ® 4.4.6 • Installing front profiles SET: SAP 5953 SET: SAP 5953 SET: SAP 5952 (corner knife bracket) (corner knife bracket) (end knife bracket) SAP 4121 SAP 1168 SAP 4122 DIN 7981 TX DIN 7380 DIN 7981 TX ST4,2x32...
Page 113 Amani ® SET: SAP 5954* SAP 5955* SAP 1128 DIN 7991 M8x20 SET: SAP 5954* SAP 5955* * SAP 5954: joining knife bracket pivot - SAP 5955: joining knife bracket span SAP 1240 BN1206 M8x10...
Page 114: Fitting Cover On Side Knife Brackets
Amani ® 4.4.7 • Fitting cover on side knife brackets SET: SAP 5953 (corner knife bracket) SAP 3686...
Page 115: Installation Of Cassettes
Amani ® 4.5 • Installation of cassettes 4.5.1 • Orientation of cassettes...
Page 116: Cassettes On Span
Amani ® 4.5.2 • Cassettes on span To determine the location of each carrier, first measure the length of the cassette SET: SAP 5958 SAP 3686...
Page 117: Cassettes On Pivot
Amani ® 4.5.3 • Cassettes on pivot START MIDDLE SPAN START MIDDLE...
Page 118 Amani ® SET: SAP 5958 SAP 3686 Ø 4 mm...
Page 119: Installing Blades Under Canopy
Amani ® SET: SAP 5958 SAP 3686 4.5.4 • Installing blades under canopy CLICK...
Page 120: Installing End Cap For End Knife Bracket
Amani ® 4.5.5 • Installing end cap for end knife bracket SET: SAP 5952 SAP 3788 DIN916 M5x12 2,5 mm 4.5.6 • Installing end cap on corner SET: SAP 5953 SAP 1240 BN1206 M8x10...
Page 121: Canopy Without Iconic Led-Line
Amani ® 4.6 • Canopy without iconic LED-line Fitting cover on front profile CLICK 4.7 • Fitting cables with optional LED lighting Rules: 1. Cable iconic LED-line can be installed via the end knife or the corner knife bracket on the pivot side 2.
Page 122: Via Corner Knife Bracket
Amani ® 4.7.1 • Via corner knife bracket ICONIC LED-LINE ALONG SPAN PIVOT SPAN...
Page 123 Amani ® CLICK CABLE...
Page 124 Amani ® ICONIC LED-LINE ALONG PIVOT PIVOT...
Page 125 Amani ® CABLE CLICK...
Page 126 Amani ® ICONIC LED-LINE ALONG PIVOT AND SPAN PIVOT...
Page 127 Amani ® CONNECTING CABLES AT CORNER KNIFE BRACKET POWER IO RECEIVER SUPPLY...
Page 128: Via End Knife Bracket
Amani ® 4.7.2 • Via end knife bracket...
Page 129 Amani ® CONNECTING CABLES AT END KNIFE BRACKET POWER IO RECEIVER SUPPLY...
Page 130: Multiple Iconic Led-Line On One Canopy Side
Amani ® 4.7.3 • Multiple iconic LED-line on one canopy side...
Page 131: Fitting Cover On Side Profile
Amani ® 4.8 • Fitting cover on side profile CLICK CLICK cable iconic LED-line...
Page 132: Fitting Caps On Pivot Side
Amani ® 4.9 • Fitting caps on pivot side 90° CLICK Iconic LED-line...
Page 133: Comfort Blades
Amani ® COMFORT BLADES...
Page 134: Accessories Roof
Amani ® 5 • Accessories roof 5.1 • Protecto...
Page 135 Amani ® 90°...
Page 136 Amani ®...
Page 137 Amani ®...
Page 138 Amani ® SET: SAP 5496 SAP 1249 DIN7380 M6x16...
Page 139: Lineo Heat
Amani ® 5.2 • Lineo Heat 5.2.1 - Position the Amani drill jig on the high pivot side SAP 5477 90°...
Page 140 Amani ® Be careful of underlying cables Ø 4 mm when drilling Note: push the jig down while drilling.
Page 141: Position The Jig On The Low Pivot Side
Amani ® 5.2.2 - Position the jig on the low pivot side 90°...
Page 142: Installing The Fixation Bracket
Amani ® Be careful of underlying cables when drilling Ø 4 mm Note: push the jig down while drilling. 5.2.3 • Installing the fixation bracket SET: SAP 5474 SET: SAP 5474 SAP 5408 SAP 5408 DIN7982 CH DIN7982 CH St4,8x19...
Page 143: Connecting The Wiring Of The Heating Element
Amani ® 5.2.4 • Connecting the wiring of the heating element io receiver Heat Quickon io receiver io receiver Heat Heat Quickon Quickon Max. 3 heaters can be connected to 1 electrical circuit of 20A.
Page 144 Amani ® 3G25 HEAT 1 HEAT 2 Power led Status led If a receiver is provided, plug the power cable into the receiver. To do so, first remove the transparent cover of the receiver and insert the power cable through the open cable gland into the receiver.
Page 145 Amani ® See enclosed instructions with the connector Blue = pin 1 Brown = pin 2 Green/yellow = PE (earthing)
Page 146: Installing The Lineo Heat
Amani ® 5.2.5 • Installing the Lineo Heat...
Page 147 Amani ®...
Page 148 Amani ® CLICK...
Page 149 Amani ® 3 mm View from the underside of the Lineo Heat blade with alignment between two standard blades 8 mm View from the underside of the Lineo Heat blade...
Page 150: Set Up The Heat Using The Hand-Held Remote (Io)
Amani ® 5.2.6 • Set up the Heat using the hand-held remote (io) Note: Check if the device is has 230V power. 0,5 sec. Select the desired channel on the Situo io hand-held remote. Press the UP and DOWN buttons briefly at the same time on the hand-held remote until the heating element briefly switches on and then switches off.
Page 151: Lineo Fix
Amani ® 5.3 • Lineo Fix 5.3.1 - Position the jig on the high pivot side 90°...
Page 152 Amani ® Be careful of underlying cables Ø 4 mm when drilling Note: push the jig down while drilling.
Page 153: Position The Jig On The Low Pivot Side
Amani ® 5.3.2 - Position the jig on the low pivot side 90°...
Page 154: Installing The Fixation Bracket
Amani ® Be careful of underlying cables when drilling Ø 4 mm Note: push the jig down while drilling. 5.3.3 • Installing the fixation bracket SET: SAP 5474 SET: SAP 5474 SAP 5408 SAP 5408 DIN7982 CH DIN7982 CH St4,8x19...
Page 155: Installing The Lineo Fix
Amani ® 5.3.4 • Installing the Lineo Fix...
Page 156 Amani ®...
Page 157 Amani ® CLICK...
Page 158 Amani ® 3 mm View from the underside of the Lineo Fix blade with alignment between two standard blades 8 mm View from the underside of the Lineo Fix blade...
Page 159: Lineo Luce
Amani ® 5.4 • Lineo Luce Compatibility/restrictions 1, 2,..,2 ,1 MAX. 5 LINEO LUCE...
Page 160 Amani ® CLICK High side SET: SAP 7040 Low side...
Page 161: Lineo Led
Amani ® 5.5 • Lineo LED...
Page 162 Amani ® High side CLICK Low side...
Page 163: Infills
Amani ® INFILLS...
Page 164: Fixscreen
Amani ® 6 • Fixscreen 6.1 • Installation L-junction with columns (place side guiding channel on both columns) CLICK CLICK CLICK CLICK I-junction with columns (place side guiding channel on both columns) CLICK CLICK CLICK CLICK...
Page 165 Amani ® SET: SAP 6021 SAP 6214 DIN7500E Ø 4,5 mm M5x20...
Page 166 Amani ® Installation of cover column CLICK...
Page 167 Amani ® SET: SAP 6021...
Page 168 Amani ® CLICK CLICK...
Page 169 Amani ® RITS CLICK...
Page 170 Amani ® SET: SAP 6021 SAP 6033 DIN7981-TX Ø 4 mm ST4,8x9,5 SET: SAP 6021 SAP 6033 DIN7981-TX ST4,8x9,5 Only screws for Fixscreen!
Page 171: Setting Fixscreen End Points
Amani ® 6.2 • Setting Fixscreen end points Note: • Check whether the device is connected to a 230V power supply. • If there are multiple Fixscreen, these must never be powered together. 0,5 sec. 0,5 sec. Select the desired channel on the situo io hand-held Press the remote’s UP and DOWN button simultaneously (briefly).
Page 172 Amani ® 0,5 sec. 0,5 sec. Press the UP button on the remote until you have reached the desired upper end point. Press the MY and the DOWN buttons on the remote simultaneously (briefly) to confirm this upper end point.
Page 173 Amani ® 0,5 sec. > 2 sec. 0,5 sec. > 2 sec. STOP STOP Press briefly on the MY button to stop the Fix screen Press for more than 2 sec. on the MY button until the Fix screen movement at any point.
Page 174: Moving The Fixscreen Endpoints
Amani ® 6.3 • Moving the Fixscreen endpoints 0,5 sec. 0,5 sec. 0,5 sec. 0,5 sec. > 5 sec. > 5 sec. > 5 sec. > 5 sec. > 2 sec. > 2 sec. > 2 sec. > 2 sec.
Page 175: Returning To The Fixscreen Default Settings
Amani ® 6.4 • Returning to the Fixscreen default settings 2 sec. 8 sec. 2 sec. 8 sec. 2 sec. 8 sec. 2 sec. 2 sec. 8 sec. 2 sec. 2 sec. 2 sec. 8 sec. 2 sec. 2 sec.
Page 176: Fixed Wall
Amani ® 7 • Fixed wall 7.1 • Installing the support posts SET: SET: SET: 90° SAP 6381 (Linarte) SAP 6381 (Linarte) SAP 6381 (Linarte) SAP 6380 (Casco) SAP 6380 (Casco) SAP 6380 (Casco) SAP 953 SAP 961 SAP 1223...
Page 177 Amani ® 200-300 mm max. max. 600 mm 600 mm...
Page 178 Amani ® INSIDE OUTSIDE SET: SAP 6381 (Linarte) SAP 6380 (Casco) OUTSIDE SAP 4114 DIN7504 K St4,8x25 INSIDE Fixing a beam against the column can help align the support posts.
Page 179 Amani ® 90° SET: SAP 6381 (Linarte) SAP 6380 (Casco) SAP 1223 M8x20 SET: SET: SAP 6381 (Linarte) SAP 6381 (Linarte) SAP 6380 (Casco) SAP 6380 (Casco) Secure the support posts. Use fasteners adapted to the relevant surface (to be provided by the installer).
Page 180: Installation Of The Skirting Profile
Amani ® 7.2 • Installation of the skirting profile FLOOR...
Page 181 Amani ® Option 1: for a column without overlength Option 2: for a column with overlength FLOOR...
Page 182: Installation Of The Linarte Support Profile
Amani ® 7.3 • Installation of the Linarte support profile SET: SAP 6381 1x/post SAP 4114 DIN7504 K St4,8x25 SET: SAP 6381 SAP 4114 DIN7504 K St4,8x25 30 mm FLOOR The support profile must be level. If the slope is slanted, the support profile must...
Page 183: Installation Of Casco Brackets
Amani ® 7.4 • Installation of Casco brackets ± 600 mm 90°...
Page 184 Amani ® 90° SET: SAP 6381 (Linarte) SET: SET: SAP 6380 (Casco) SAP 6381 (Linarte) SAP 6381 (Linarte) SAP 6380 (Casco) SAP 6380 (Casco) SAP 1223 M8x20 SAP 953 SAP 961 DIN 9021 M8 DIN 985 M8...
Page 185: Installation Of The Linarte Supporting Profiles
Amani ® 7.5 • Installation of the Linarte supporting profiles max. 300 mm max. 1200 mm max. 1200 mm 400 mm SET: SAP 6381 3x/post SAP 4114 DIN7504 K St4,8x25...
Page 186: Installation Of The Linarte Profiles
Amani ® 7.6 • Installation of the Linarte profiles CLICK CLICK CLICK CLIPS 150 Use up all 150 clips first and divide them equally among the number of Linarte support profiles.
Page 187 Amani ® CLICK CLIPS 60...
Page 188 Amani ® CLICK Alternating profiles 1 2 3 4 6 CLICK...
Page 189 Amani ® CLICK 30 mm CLICK...
Page 190 Amani ® CLICK ± 2 mm ± 2 mm...
Page 191: Fixed Wall With Door
Amani ® 8 • Fixed wall with door (view from the outside) Option 1: door in the middle Option 2: door on the left Option 3: door on the right...
Page 192: Installing The Support Posts
Amani ® 8.1 • Installing the support posts 90° SET: SET: SET: SAP 6381 (Linarte) SAP 6381 (Linarte) SAP 6381 (Linarte) SAP 6380 (Casco) SAP 6380 (Casco) SAP 6380 (Casco) SAP 953 SAP 961 SAP 1223 DIN 9021 M8 DIN 985 M8...
Page 193 Amani ® 200-300 mm max. max. 600 mm 600 mm...
Page 194 Amani ® INSIDE OUTSIDE SET: SAP 6381 (Linarte) SAP 6380 (Casco) OUTSIDE SAP 4114 DIN7504 K St4,8x25 INSIDE Fixing a beam against the column can help align the support posts.
Page 195 Amani ® 90° SET: SAP 6381 (Linarte) SAP 6380 (Casco) SAP 1223 M8x20 SET: SET: SAP 6381 (Linarte) SAP 6381 (Linarte) SAP 6380 (Casco) SAP 6380 (Casco) SAP 953 SAP 961 DIN 9021 M8 DIN 985 M8...
Page 196: Installation Of The Column Cover Plates
Amani ® 8.2 • Installation of the column cover plates Door left Door right CLICK CLICK CLICK CLICK...
Page 197: Determining The Position Of The Door
Amani ® 8.3 • Determining the position of the door Door in the middle Door left Door right SET: SAP 6253 (Linarte) SAP 6279 (Casco) SAP 1174 DIN7981 CH St4,8x9,5 Ø 4 mm...
Page 198: Installation Of The Door Frame
Amani ® 8.4 • Installation of the door frame LINARTE CLICK SET: SAP 6253 18x CLIPS 60 UNFINISHED SET: SAP 6279 SAP 920 DIN7981 CH St4,2x13...
Page 199 Amani ® Adjust the height of the door 13 mm CLICK...
Page 200 Amani ® Only positioning; not screwing SAP 5685 SCREW FLEXGUIDE...
Page 201: Installation Of The Door Frames
Amani ® Secure the bottom rail. Use screws that are suitable for the surface, e.g. DIN 7982 CH - ST4.2x13 (not supplied). 8.5 • Installation of the door frames...
Page 202 Amani ® Door in the middle 1111 mm 1111 mm Door left Door right 996 mm 996 mm...
Page 203 Amani ® Door below the joining beam left Door below the joining beam right 1146 mm 1146 mm Left side of the door Right side of the door Only positioning; not screwing Only positioning; not screwing...
Page 204: Installation Of The Support Posts On The Door Frames
Amani ® 8.6 • Installation of the support posts on the door frames SET: SAP 6381 (Linarte) SAP 6380 (Casco) SAP 1223 M8x20 90° SET: SAP 6381 (Linarte) SAP 6380 (Casco) SAP 953 DIN 9021 M8 SET: SAP 6381 (Linarte)
Page 205 Amani ® SET: SAP 6381 (Linarte) SAP 6380 (Casco) SAP 4114 DIN7504 K St4,8x25 SET: SAP 6381 (Linarte) SAP 6380 (Casco) SAP 1223 M8x20...
Page 206 Amani ® SET: SAP 6381 (Linarte) SAP 6380 (Casco) SAP 953 DIN 9021 M8 SET: SAP 6381 (Linarte) SAP 6380 (Casco) SAP 961 DIN 985 M8...
Page 207 Amani ®...
Page 208: Installation Of The Door Lock
Amani ® 8.7 • Installation of the door lock SET: SAP 6253 (Linarte) SAP 6279 (Casco) SAP 1178 DIN 7982 CH St4,2x13 ± 1 mm Ø 4 mm...
Page 209: Installation Of Unfinished Brackets Between The Support Posts
Amani ® SET: SAP 6253 (Linarte) SAP 6279 (Casco) SAP 1239 DIN7981CH St4,8x50 8.8 • Installation of unfinished brackets between the support posts ± 600 mm...
Page 210 Amani ® 90° 90° SET: SET: SET: SAP 6381 (Linarte) SAP 6381 (Linarte) SAP 6381 (Linarte) SAP 6380 (Casco) SAP 6380 (Casco) SAP 6380 (Casco) SAP 953 SAP 961 SAP 1223 DIN 9021 M8 DIN 985 M8 M8x20...
Page 211: Installation Of Unfinished Front Brackets
Amani ® 8.9 • Installation of unfinished front brackets Ø 4 mm max. 600 mm SET: SAP 6380 SAP 1174 DIN7981CH St4,8x9,5 8.10 • Installation of the plinth(s)
Page 212 Amani ® Option 1: for a column without overlength Option 2: for a column with overlength FLOOR...
Page 213: Installation Of The Linarte Support Profile
Amani ® 8.11 • Installation of the Linarte support profile SET: SAP 6381 1x/post SAP 4114 DIN7504 K St4,8x25 SET: SAP 6381 SAP 4114 DIN7504 K St4,8x25 30 mm FLOOR The support profile must be level. If the slope is slanted, the support profile must...
Page 214: Installation Of The Brackets Above The Linarte Door Opening
Amani ® 8.12 • Installation of the brackets above the Linarte door opening SET: SAP 6379 SAP 7080 DIN7504 M St4,8x16...
Page 215 Amani ® SET: SAP 6381 SAP 4114 DIN7504 K St4,8x25...
Page 216: Installation Of The Brackets In The Upper Beam - Unfinished
Amani ® 8.13 • Installation of the brackets in the upper beam - unfinished SET: SAP 6379 SAP 7080 DIN7504 M St4,8x16...
Page 217: Installation Of The Linarte Supporting Profiles
Amani ® 8.14 • Installation of the Linarte supporting profiles max. 1200 mm max. 1200 mm SET: SAP 6381 3x/post SAP 4114 DIN7504 K St4,8x25...
Page 218: Installation Of The Linarte Profiles
Amani ® 8.15 • Installation of the Linarte profiles CLICK CLICK CLIPS 150 Use up all 150 clips first and divide them equally among the number of Linarte support profiles.
Page 219 Amani ® CLICK CLICK Nx CLIPS 60...
Page 220 Amani ® Alternating profiles 1 2 3 4 6 CLICK CLICK...
Page 221 Amani ® CLICK CLICK...
Page 222 Amani ® CLICK CLICK 1x CLIPS 150 1 2 3 4 6 Alternating profiles Nx CLIPS 60...
Page 223 Amani ® CLICK CLICK...
Page 224 Amani ® CLICK ± 2 mm...
Page 225: Finishing The Linarte Door
Amani ® 8.16 • Finishing the Linarte door 18x CLIPS 60...
Page 226 Amani ® Alternating profiles 28 mm 28 mm...
Page 227: Loggia
Amani ® 9 • Loggia 9.1 • Loggia sliding panels Possible positions Single beam Coupling beam Zone A Zone B Zone D In the rail(s) where the roller system is provided...
Page 228 Amani ® Roller assembly positions...
Page 229 Amani ® Installing Flexguide channels on bottom rail Position of the bottom rail AMANI SAP 6986 PLACE AGAINST COLUMN ZONE A - RAIL = 46mm ZONE A...
Page 230 Amani ® AMANI V0013016 SAP 6986 OUTSIDE ZONE B - RAIL 1 = 23.5mm ZONE B - RAIL 2 = 75.5mm ZONE B - RAIL 3 = 127.5mm ZONE B Fixing bottom rails to the substructure 49 mm 49 mm ZONE D Use screws that are suitable for the surface, e.g.
Page 231 Amani ® Releasing Autofix Installing Loggia panel 8 mm Loggia Loggia Privacy...
Page 232 Amani ® CLICK SET: SAP 5686 SAP 5685 SCREW FLEXGUIDE 3 mm...
Page 233 Amani ® Setting height 13 mm Installing position lock CLICK...
Page 234 Amani ® 2 mm CLICK...
Page 235: Loggia Folding Panels
Amani ® 9.2 • Loggia folding panels Possible positions Beam Beam Coupling beam with canopy Zone A Zone D In the rail where the roller system is provided...
Page 236 Amani ® Roller assembly positions...
Page 237 Amani ® Installing Flexguide channels on bottom rail START MIDDLE GUIDING CHANNELS Number of panels Number of middle guiding channels Number of panels...
Page 238 Amani ® Position of the bottom rails ZONE A AMANI SAP 6986 PLACE AGAINST COLUMN ZONE A - RAIL = 46mm 49 mm 49 mm ZONE D...
Page 239 Amani ® Fixing bottom rails to the substructure Use screws that are suitable for the surface, e.g. DIN 7982 CH - ST4.2x13 (not supplied). Installation of folding panels...
Page 240 Amani ® SET: SAP 5686 SAP 5685 SCREW FLEXGUIDE 3 mm SAP 6104 DIN916 M6x12 3 mm Only for the first panel!
Page 241 Amani ® SET: SAP 5686 SAP 5685 SCREW FLEXGUIDE 3 mm...
Page 242 Amani ® Hinge installation Installing cover plates SET: SAP 30845 SAP 920 DIN7981CH ST4,2x13 Ø 3,5 mm Make sure the cover plates reach up to the hinge.
Page 243 Amani ® Installation of last folding panel SET: SAP 30845 SAP 920 DIN7981CH ST4,2x13...
Page 244 Amani ® SET: SAP 5686 SAP 5685 SCREW FLEXGUIDE 3 mm Installing position lock to place folding panels in stacking position CLICK...
Page 245 Amani ® 2 mm...
Page 246 Amani ® Installing cover plates CLICK CLICK CLICK CLICK CLICK CLICK CLICK CLICK CLICK CLICK CLICK...
Page 247: Loggia Fixed Panels
Amani ® 9.3 • Loggia fixed panels Possible positions Single beam Coupling beam In the rail where the roller system is provided...
Page 248 Amani ® Adjusting panel height BEAM LOGGIA 13 mm...
Page 249 Amani ® Drill hole Ø 20 / depth 40 mm FLOOR between column and panel between two panels 25,4 mm 15,2 mm 75,5 mm To make it easier to drill the hole, the cover plate can be removed from the column.
Page 250: Glass Sliding Panels
Amani ® 10 • Glass sliding panels 10.1 • Installation of bottom rail Always install the bottom rail horizontally! SPAN PIVOT 4 RAILS 5 RAILS SPAN PIVOT 14,5 mm 14,5 mm...
Page 251 Amani ® Max. 400 mm Ø5 Ø10/90°...
Page 252: Installation Of Glass Panels
Amani ® 10.2 • Installation of glass panels Order of installation Order of installation Order of installation INSIDE INSIDE INSIDE OUTSIDE OUTSIDE OUTSIDE...
Page 253 Amani ®...
Page 254 Amani ® Order of installation of glass panels FIXED SIDE SLIDING SIDE...
Page 255: Fitting The Lift Out Protection (With Optional Lock)
Amani ® 10.3 • Fitting the lift out protection (with optional lock) Ø 3,5 mm 140 mm SAP 859 DIN965 TX M4X20...
Page 256: Fitting The Vertical Profiles
Amani ® 10.4 • Fitting the vertical profiles FIXED SIDE SLIDING SIDE TAPE FIXED SIDE 49,5 mm...
Page 257 Amani ® SLIDING SIDE SET: SAP 6615 SAP 1186 DIN7981 CH Ø 4 mm ST4,8x19 SLIDING SIDE...
Page 258: Fitting The Stoppers
Amani ® 10.5 • Fitting the stoppers Ø 5 mm IF THERE IS NO LOCK, THE FIRST PANEL ALSO NEEDS A STOPPER Ø 5 mm...
Page 259 Amani ® SET: SAP 6615 SAP 1153 DIN912 M6x16...
Page 260: Curtains
Amani ® 11 • Curtains 11.1 • Fitting the guiding channels in the rail 11.2 • Fitting the stoppers at both ends of the rail...
Page 261: Position Of The Rail On The Beam
Amani ® 11.3 • Position of the rail on the beam Zone B Permitted position in zone B min. 20 mm Zone C...
Page 262: Fitting The Rail
Amani ® 11.4 • Fitting the rail TAPE 15,5 mm x 0,8 mm SET: SAP 369 SAP 1153 DIN7981CH Ø 2,5 mm St2,9x9,5...
Page 263: Fixing The Curtain To The Rail
Amani ® 11.5 • Fixing the curtain to the rail 11.5.1 • Preparation...
Page 264: Fixing The Curtain
Amani ® 11.5.2 • Fixing the curtain OUTSIDE INSIDE 11.5.3 • Maintenance instructions Steam in horizontal direction only.
Page 265: Comfort Lighting
Amani ® COMFORT LIGHTING...
Page 266: Spot Lighting
Amani ® 12 • Spot lighting Test the spotlights before installing them in the canopy cover THROUGH NODE(S) UNDERNEATH TOP COVER OF BEAM CABLE 6,5m THROUGH NODE POWER CONTROL BOX CABLE 6,5m SUPPLY max. 14 spots/control box max. 8 spots/channel...
Page 267: Wiring In The Rail
Amani ® 12.1 • Wiring in the rail Insert 2 m of cable through the junction...
Page 268 Amani ® In combination with louvered canopy Slide the cable under the water funnel.
Page 269 Amani ® Span...
Page 270 Amani ® CLICK Pivot...
Page 271 Amani ® CLICK...
Page 272 Amani ® Determine the position of the spotlights Wiring up to the spotlights Compatibility/restrictions: long distance = 2m cable long distance = 2m cable CABLE 2m Max. 5 x...
Page 273 Amani ® T-cable interconnection Fitting the cables in the rail CABLES...
Page 274 Amani ®...
Page 275: Connecting Wiring To The Spotlights
Amani ® 12.2 • Connecting wiring to the spotlights CHANNEL 1 CHANNEL 2 CHANNEL 3 CHANNEL 4...
Page 276 Amani ® Adjusting the position of the spotlight...
Page 277 Amani ® Removing the spotlight from the rail...
Page 278: Connecting Spotlights To Control Unit
Amani ® 12.3 • Connecting spotlights to control unit Through a junction NO OPEN CONNECTOR END 230 V POWER CONTROL BOX SUPPLY 6,5 m...
Page 279 Amani ® Through multiple junctions ADDITIONAL POWER CONTROL BOX SUPPLY BRANCH 6,5 m 230V 6,5 m 6,5 m...
Page 280 Amani ® Interconnect extension cables (6.5 m) 6,5 m 6,5 m 6,5 m...
Page 281: Use The Tool To Remove The Cable From The Rail
Amani ® 12.4 • Use the tool to remove the cable from the rail CABLE...
Page 282 Amani ®...
Page 283: Setting The Spot Lighting
Amani ® 12.5 • Setting the spot lighting 12.5.1 • Setting the spot lighting spot(s) 1 POWER CONTROL BOX spot(s) 1 SUPPLY 230V CONTROL BOX POWER SUPPLY spot(s) 1 spot(s) 1 230V CONTROL BOX POWER CONTROL BOX SUPPLY 230V Note: If there are multiple controls, these must never be powered together.
Page 284 Amani ® prog Situo 5 Variation A/M io Pure II Press the PROG button briefly on the back of the Situo IO remote control. This confirms the setting. SPOTLIGHT(s) 2 < 0,5 sec. prog Situo 5 Variation A/M io Pure II...
Page 285: Setting The Situo Variation Io Remote Control To User Mode 2
Amani ® 12.5.2 • Setting the Situo Variation io remote control to user MODE 2 The Situo Variation io comes with 4 preprogrammed user modes. This enables you to choose the right user mode depending on the system type of the group to be controlled.
Page 286: Returning The Led Lighting To Factory Settings
Amani ® 12.5.3 • Returning the LED lighting to factory settings Situo 5 4 sec. You can perform an LED lighting ‘Memory Reset’ (Colomno-, UpDown- or Lineo Disconnect the connector between the transformer and receiver for 4 seconds. LED lighting).
Page 287 Amani ® 10 sec. 4 sec. Reconnect the connector for approximately 10 seconds Disconnect the connector between the transformer and (min. 5 seconds and max. 15 seconds). receiver again for 4 seconds. 10 sec. prog Situo 5 Variation A/M io Pure II Reconnect the connector.
Page 288: Ambient Roof Led
Amani ® 13 • Ambient roof LED 13.1 • Position in the canopy 13.2 • Connecting wiring...
Page 289: Fitting The Finishing Profile Over The Cable
Amani ® 13.3 • Fitting the finishing profile over the cable...
Page 290 Amani ®...
Page 291: Interconnecting Cables
Amani ® 13.4 • Interconnecting cables POWER IO RECEIVER SUPPLY...
Page 292: Led Beam Fixed Roof
Amani ® 14 • LED beam fixed roof 14.1 • Determining the position of the LED beam PIVOT 14.2 • Using the jig provided to drill holes...
Page 293 Amani ® Ø 5,5 mm Depth 14,20 Ø 3,5 mm zone C or C' zone C or C' with rail zone C or C' zone C or C' with rail Max. Ø 22 mm...
Page 294: Installation Of Wiring
Amani ® 14.3 • Installation of wiring POWER IO RECEIVER SUPPLY LED BEAM STORAGE LED...
Page 295 Amani ®...
Page 296 Amani ® LED beam parallel to the pivot CLICK LED beam parallel to the span CLICK...
Page 297: Fitting The Corner Piece
Amani ® 14.4 • Fitting the corner piece SET: SAP 6631 SAP 920 DIN7981 CH St4,2x13...
Page 298: Installation Of Led Beam
Amani ® 14.5 • Installation of LED beam CLICK...
Page 299 Amani ® SET: SAP 6631 SAP 2070 DIN7380 M6x20 CLICK...
Page 300: Connecting The Control Unit
Amani ® 14.6 • Connecting the control unit POWER IO RECEIVER SUPPLY...
Page 301: Comfort Automation
Amani ® COMFORT AUTOMATION...
Page 302: Power Socket
Amani ® 15 • Power socket SET: – SAP 6299 (usb power socket) – SAP 6300 (power socket type F) – SAP 6301 (power socket type E) – SAP 6324 (empty power socket)
Page 303: Sensors
16.1 • Mounting the rain sensor Strictly observe the installation instructions for the rain sensor to avoid intrusion of water. It is advisable to stick the rain sensor to the Amani. Note: if you still want to fit a rain sensor, screw it...
Page 304 Remove the protective film from the fixation tape and stick the the rain sensor. Fill the ring inside entirely with silicone sensor onto the Amani structure. and make sure that the silicone is even higher than the Note: the fixation tape holds the sensor in place for first 24 hours, thickness of the ring.
Page 305: Installing The Wind Sensor
Amani ® 16.2 • Installing the wind sensor Position the Somfy Eolis wind sensor in an open place. The wind sensor can be installed at different angles and you fasten it with 2 screws. 2 x 0,75 mm 230V - 50Hz...
Page 306 Amani ® 0,5 sec. > 7 sec. > 2 sec. 3 sec. 3 sec. 0,5 sec. prog prog prog prog Situo 5 RTS Pure II Situo 5 RTS Pure II Situo 1 Soliris A/M RTS Pure II Situo 5 Variation...
Page 307: Construction Finishing
Amani ® CONSTRUCTION FINISHING...
Page 308: Finishing
Amani ® 17 • Finishing 17.1 • Installation of top covers...
Page 309 Amani ® Overview of the different top covers Standard beam Coupling beam Beam against the wall Beam with Loggia in zone A...
Page 310: Installation Of Upper Corner Caps
Amani ® 17.2 • Installation of upper corner caps SAP 1244 DIN7991 M6x80...
Page 311 Amani ® Overview of upper corner caps of an L junction Standard Wall Loggia Zone A BEAM LEFT Standard SAP 6815 SAP 3628 SAP 3631 Wall SAP 3629 SAP 3630 SAP 3634 Loggia Zone A SAP 3632 SAP 3633 SAP 3635...
Page 312 Amani ® Overview of upper corner caps of a T junction Standard Wall Loggia Zone A SAP 3636 SAP 3637 SAP 3638...
Page 313: Water Test 2: Checking The Nodes
Amani ® 17.3 • Water test 2: checking the nodes Test the nodes to ensure that they are watertight. Do this as follows: • This requires that the following installation steps have already been carried out: 1. Vertical finishing profile in the inside corners is already installed.
Page 314 All photos shown are for illustrative purposes; the actual product may vary due to product placement. Renson reserves the right to make technical changes to the products described in this brochure. ® The most recent product information, availability, and your local distributor can always be found on www.renson.eu...

Renson amani Installation Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Renson amani

Summary of Contents for Renson amani