Advertisement
Quick Links
EN_Tips:Please do not use in bad weather to avoid damage.
FR_Conseils : Ne pas utiliser par mauvais temps afin d'éviter tout dommage.
ES_Consejos:No utilizar con mal tiempo para evitar daños.
PT_Dicas: Não utilizar com mau tempo para evitar danos.
DE_Tipps:Bitte nicht bei schlechtem Wetter verwenden, um Schäden zu vermeiden.
IT_Suggerimenti: non utilizzare in caso di maltempo per evitare danni.
EN_IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.
FR_IMPORTANT:A LIRE ATTENTIVEMENT ET À CONSERVER POUR CONSULTATION
ULTÉRIEURE.
ES_IMPORTANTE, LEA Y GUARDE PARA FUTURAS REFERENCIAS.
PT_IMPORTANTE, RETER PARA REFERÊNCIA FUTURA: LEIA ATENTAMENTE.
DE_WICHTIG! SORGFÄLTIG LESEN UND FÜR SPÄTER NACHSCHLAGEN AUFBEWAHREN.
IT _ IMPORTANTE! CONSERVARE IL PRESENTE MANUALE PER FUTURO RIFERIMENTO E
LEGGERLO ATTENTAMENTE.
IN240100110V01_US
840-268V81
US_CA
US_CA
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Outsunny 840-268V81
Summary of Contents for Outsunny 840-268V81
- Page 1 IN240100110V01_US 840-268V81 EN_Tips:Please do not use in bad weather to avoid damage. FR_Conseils : Ne pas utiliser par mauvais temps afin d'éviter tout dommage. ES_Consejos:No utilizar con mal tiempo para evitar daños. PT_Dicas: Não utilizar com mau tempo para evitar danos.
-
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS Read all instructions before using DANGER – To reduce the risk of electric shock: 1. Always unplug this furnishing from the electrical outlet before cleaning or servicing WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons: 2. - Page 5 1Pcs 1Pcs 1Pcs 1Pcs 1Pcs 1Pcs 1Pcs 1Pcs 1Pcs 1Pcs 1Pcs 1Pcs 2Pcs 2Pcs 2Pcs 1Pcs 1Pcs 2Pcs St3X10 St4X15 3Pcs 2Pcs 3Pcs 2Pcs 2Pcs 32Pcs M8X55 M6X40 8Pcs 8Pcs 3Pcs 4Pcs 4Pcs 8Pcs M5X12 M5X8 4Pcs 8Pcs 1Pcs 1Pcs 4Pcs 8Pcs St4X12...
- Page 7 1Pcs 1Pcs 3Pcs...
- Page 8 STEP2：Connecting Roller tube And Front Bar（Right and middle） St4X15 2Pcs 1Pcs 1Pcs 2Pcs 1Pcs 1Pcs 24Pcs...
- Page 9 St4X15 1Pcs 1Pcs 8Pcs...
- Page 10 2Pcs 3Pcs 2Pcs 2Pcs...
- Page 12 STEP6: Roller Support Assembly...
- Page 13 STEP7: 1.Connecting the wire(left and right) 2.Connecting the Torsionbar and screwed it later 3.Put the Roller into the square hole of the gear box and Round Square of the roller support 4.Connect the two torsion bar Find The Right Direction Insertin Male plug Male plug...
- Page 14 STEP8:Setting Awning Position 1.Move the arm - Link until the front bar wrist suppore is Connected throught it . 2.Align the from bar and the arm . and tighten the screw part 3.Then tighten the adjustable bolt up to 90% tight 3Pcs...
- Page 15 Step9:Conecting the Alu Cover 1.Conecting the Alu Cover(10 part,29 part,30 part ，43 partand 34 part together) and ②） 2.Put the Alu cover on the Torsion bar(①， M5X12 M5X8 2Pcs 1Pcs 1Pcs 1Pcs 4Pcs 8Pcs 12Pcs 2Pcs 2Pcs...
- Page 16 STEP10:1.Hammer the Left support and Right Support 2.Conect the Support and Alu cover. St4X12 1Pcs 1Pcs 6Pcs...
- Page 17 STEP11:1.Finishing Awning Assembly Note:If the Remote Awning，Please set awning opening and closing Rang，Before you use the Awning.
- Page 19 Wall bracket leveled against horizontal line Wall bracket Wall bracket Wall bracket level(horizontal line)
- Page 22 Button Specification Technical specification Battery: 3V (AAA battery×2) Battery life: >2 years Radio frequency: 433.925MHz Transmitting power: 10 mW Quiescent current: ≤5uA Transmitting current: ≤20mA Working temperature: -5℃~50℃ Radio range: 35 meters indoor Warning 1, Emitter couldn't expose to moisture or be striked heavily, or else the emitter life will be affected. 2, If the emitter is not so sensitive or the radio range becomes shorter, pls check whether to change the battery.
- Page 23 A - Set awning closing range B - Set awning opening range...
-
Page 24: Troubleshooting
1 Pairing Beep T>10s 6 times Setting up is ok Power off Power on Press once Press once Press once * Press UP, the awning will be retracted (closed); Press DOWN, the awning will be extended (opened). 2 Pairing Additional Emitter Beep 5 times New emitter is paired to the motor...
Need help?
Do you have a question about the 840-268V81 and is the answer not in the manual?
Questions and answers