Table of Contents
Advertisement
Quick Links
RC21214/RC21213
This document describes the following topics about
the RC21214/RC21213 programmer board:
■
Basic hardware and GUI setup
■
Instructions to burn OTP memory of a device from
the GUI
Computer Requirements
■
USB 2.0 or USB 3.0 Interface
■
Processor: Minimum 1GHz
■
Memory:
●
Minimum: 512MB
●
Recommended: 1GB
■
Available disk space:
●
Minimum: 600MB (1.5GB 64-bit)
●
Recommended: 1GB (2GB 64-bit)
Board Contents
■
RC21214/RC21213 programmer board (this is the
same programmer board that is used for the
®
VersaClock
7 RC21008 and RC31008.)
■
Programmer board manual
■
Configuration software (Renesas IC Toolbox)
■
Board schematic and BOM
R31UH0029EU0101 Rev.1.01
Apr 29, 2024
Figure 1. RC21214/RC21213 Programmer Board
Programmer Board Manual
Features
■
USB power supply
■
Specialized device socket
■
Access to two differential input clocks
■
Test points for twelve differential output clocks
■
XIN terminal can use a laboratory signal generator
or OCXO/TCXO/XO evaluation board
■
Serial port for configuration and register read out
Page 1
© 2024 Renesas Electronics
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Renesas RC21214
Summary of Contents for Renesas RC21214
-
Page 1: Figure 1. Rc21214/Rc21213 Programmer Board
Available disk space: ● Minimum: 600MB (1.5GB 64-bit) ● Recommended: 1GB (2GB 64-bit) Board Contents ■ RC21214/RC21213 programmer board (this is the same programmer board that is used for the ® VersaClock 7 RC21008 and RC31008.) ■ Programmer board manual ■... -
Page 2: Table Of Contents
Figure 10. StaticMultiConfig Menu ........................... 7 Figure 11. Config Selection Options ......................... 8 Figure 12. Device Connection ..........................8 Figure 13. Program OTP ............................9 Figure 14. RC21214/RC21213 Evaluation Board (Top) ..................10 Figure 15. RC21214/RC21213 Evaluation Board (Bottom) ..................10 R31UH0029EU0101 Rev.1.01 Page 2... -
Page 3: Functional Description
Operational Characteristics The RC21214/RC21213 programmer board is equipped with a single on-board LDO that takes voltage in from USB and supplies 3.3V to all device power domains. The board is designed to plug directly into any PC and be ready for use with the RICBox GUI and blank part. -
Page 4: Part Placement
RC21214/RC21213 Programmer Board Manual 1.2.1. Part Placement Part placement should follow the first pin marked on both the programmer board socket and blank part. Ensure both markings match before placing the part into the socket. Figure 3. Pin 1 Location Note: It is critical to ensure that pin 1 markings match between the board and device;... -
Page 5: Jumper Selection
1.2.2. Jumper Selection The RC21214/RC21213 programmer board is equipped with five GPIO selection jumpers (J5-J9), four GPI selection jumpers (J10-J13), and a jumper strip for XIN/CLKIN trace paths (J4). The GPIO and GPI jumpers can be pulled high or low by placing a jumper shunt between the center pin and VDD, or GND accordingly. -
Page 6: Software Setup And Configuration
USB connector. 2. Open RICBox and navigate to an existing RC21214 or RC21213 settings file or create a new configuration. Ensure that the correct XIN and CLKIN settings are set based on J4, and the signals are driven in the programmer board depending on the configuration loaded. -
Page 7: Figure 9. Configuration Type Menu
RC21214/RC21213 Programmer Board Manual 5. Use the Configuration Type drop-down menu to select between the following: ■ NoConfig – Nothing will be programmed to OTP memory. ■ SingleConfig – Program a single configuration into the OTP common configuration. ■ StaticMultiConfig – Program multiple configurations into a device that can be selectable at device start-up. -
Page 8: Figure 11. Config Selection Options
RC21214/RC21213 Programmer Board Manual 7. Select the configs to load into OTP from RICBox. ■ Default setting is for the current working configuration. ■ Ensure all necessary configs are selected and all warnings/errors are cleared. Figure 11. Config Selection Options 8. -
Page 9: Figure 13. Program Otp
RC21214/RC21213 Programmer Board Manual 9. Press the “Program OTP” button on the OTP/EEPROM page. Figure 13. Program OTP R31UH0029EU0101 Rev.1.01 Page 9 Apr 29, 2024... -
Page 10: Board Design
2. Board Design Figure 14. RC21214/RC21213 Evaluation Board (Top) Figure 15. RC21214/RC21213 Evaluation Board (Bottom) Schematic Diagrams The RC21214/RC21213 schematic diagrams are located at the end of this document. Bill of Materials Table 2. Bill of Materials Qty. Reference Designator... - Page 11 RC21214/RC21213 Programmer Board Manual Qty. Reference Designator Description Manufacturer Part Number C25 C26 COG Surface Mount Capacitor Murata Electronics GCM1555C1H6R8BA16D X7R Surface Mount Capacitor Murata Electronics GRM155R71H102KA01D OSRAM: LED Green Diffused 0603 OSRAM LG L29K-G2J1-24-Z Surface Mount Fast Switching Diodes...
-
Page 12: Ordering Information
RC21214/RC21213 Programmer Board Manual Qty. Reference Designator Description Manufacturer Part Number FTDI: Single Channel Hi-Speed USB to Multipurpose UART/FIFO FTDI FT232HQ-REEL TXC: 25MHz ±30ppm Crystal 8pF 7M-25.000MAHV-T 60 Ohms 4-SMD, No Lead QFN Thru-Hole Socket Plastronics 40QN40S15050 41 Contacts, 0.40 Pitch, 5 × 5 Body Size 3. - Page 13 RC21214/RC21213 Programmer Board Manual Headerstrip 2X6 SMA_2 SMA_2_IN GPI3 CLKIN_0 EDGE_STR 50 OHM CK_EXT11 CLKIN_0b GPI1 SMA_2 SMA-J-P-H-ST-EM1 3.3V 49.9 0.1% GPI2 CK_EXC11 CLKIN_1 CKREXT11 33.0 CK_EXT11 SMA_1 SMA_1_IN CLKIN_1b GPI0 DNI_TP_2X2_C135H76 EDGE_STR CK_EXC11 CKREXC11 33.0 SMA_1 50 OHM SMA_IN_CAP...
- Page 14 Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products.
Need help?
Do you have a question about the RC21214 and is the answer not in the manual?
Questions and answers