Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Metra Electronics Manuals
  4. Motorcycle Accessories
  5. Saddle Tramp BC-HDR-K1
  6. Installation instructions manual

Metra Electronics Saddle Tramp BC-HDR-K1 Installation Instructions Manual

Harley-davidson street glide, electra glide, ultra, and limited models 2014-up, road glide2015-up
Hide thumbs

Advertisement

Quick Links

Download this manual
KIT COMPONENTS
• A) Radio housing • B) Radio brackets • C) #8 x 3/8" Phillips screws (4) • D) #10-32 x 1/2" Phillips steel machine screws (4)• E) Handlebar Control
interface (not shown)
A
The World's best kits.
®
Harley-Davidson Street Glide, Electra Glide,
Ultra, and Limited Models 2014-Up†
Road Glide 2015-Up†
†
Non-amplified models only
Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle
specific applications
KIT FEATURES
• ISO DDIN radio provision*
• Saddle Tramp interface with built in handlebar controls
• Water resistant enclosure for added protection
• Antenna adapter included
*This kit can only be used with an ISO DDIN
radio that has an "L" shaped chassis design.
B
C
MetraOnline.com
D
© COPYRIGHT 2021 METRA ELECTRONICS CORPORATION
BC-HDR-K1
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Fairing Disassembly
Harley Davidson Street Glide, Electra Glide,
Ultra, and Limited models 2014-up .............2-3
Harley Davidson Road Glide 2015-up..............4
Kit Assembly ..........................................................5
Saddle Tramp Interface Installation . ................6-9
WIRING & ANTENNA CONNECTIONS (Included)
Wiring Harness: Saddle Tramp interface and
harness
Antenna Adapter
Handlebar control interface
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• Torx screwdrivers • Allen wrenches
ATTENTION: With the key out of the ignition,
disconnect the negative battery terminal
before installing this product. Ensure that all
installation connections are secure before
cycling the ignition to test this product.
NOTE: Refer also to the instructions included
with the aftermarket radio.
REV. 11/10/21 INSTBC-HDR-K1

Advertisement

loading
Need help?

Need help?

Do you have a question about the Saddle Tramp BC-HDR-K1 and is the answer not in the manual?

Questions and answers

Related Manuals for Metra Electronics Saddle Tramp BC-HDR-K1

Summary of Contents for Metra Electronics Saddle Tramp BC-HDR-K1

  • Page 1 BC-HDR-K1 I N S TA L L AT I O N I N S T R U C T I O N S Harley-Davidson Street Glide, Electra Glide, TABLE OF CONTENTS Fairing Disassembly Ultra, and Limited Models 2014-Up† Harley Davidson Street Glide, Electra Glide, Road Glide 2015-Up† Ultra, and Limited models 2014-up .....2-3 Harley Davidson Road Glide 2015-up....4 †...
  • Page 2 FAIRING DISASSEMBLY Harley Davidson Street Glide, Electra Glide, Ultra, and Limited models 2014-up 1. Remove (4) T-27 Torx screws from the inner fairing. (Figure A) 2. With a firm grip on the windshield, remove (3) T-27 Torx screws. remove the windshield, the outer fairing wil lalso be loosened. (Figure B) 3. Remove the outer fairing, unplugging the headlight. (Figure C) (Figure A) (Figure C) 4. Remove (2) T-27 Torx screws to remove the fairing vent, and then remove the vent. (Figure D Continued on next page (Figure B) (Figure D) 386.257.1187 MetraOnline.com...
  • Page 3 FAIRING DISASSEMBLY (CONT) 5. Remove (11) screws securing the radio“dummy” bracket: (Figure E) a. (2) T-27 Torx screws shared with the gauge cluster and a third T-27 Torx screw to remove the gauge cluster in step 7. b. (4) 5/32" Allen screws facing outward. c. (4) T-25 Torx screws secured to the radio “dummy”. d. (1) T-25 Torx screw shared with the storage pocket. 6. Remove the radio bracket. (Figure E) Note: This bracket will be reused with the kit assembly. (Figure E) 7. Remove the gauge cluster. (Figure E) 8. Remove (4) 3/16 Allen screws from the sides of radio. (Figure F) Note: These screws will be reused with the kit assembly. 9. Slide the radio out toward the rear of the bike, disconnect the wiring, and (Figure F) then remove the radio. (Figure F) REV. 11/10/21 INSTBC-HDR-K1...
  • Page 4 FAIRING DISASSEMBLY (CONT) Harley Davidson Road Glide 2015-up 6. Remove the speaker grills with a panel removal tool and remove (1) Torx screw 1. Remove the lower torx screws on from each side. (Figure E) either side holding the wind deflector CAUTION: The fairing will be loose at this wings (only the lower two need to be point. Have a helper hold it to keep from removed). (Figure A) damaging it when removing the screws. 2. Remove (1) 3/16" Allen screw from each 7. Remove the fairing and set aside. (Figure A) (Figure D) of the turn signals. (Figure B) 8. Remove (4) 3/16" Allen screws from the 3. Remove (4) Phillips screws from the sides of the factory radio. windshield and set the windshield Note: These screws will be reused in the aside. (Figure C) BC-HDR-K1 kit assembly. 4. Remove the top fairing trim clipped to CAUTION: Be sure to hold the radio the top of the radio. (Figure D) when removing the last screw so it does...
  • Page 5 KIT ASSEMBLY 1. Secure the radio brackets to the radio housing with (4) #8 x 3/8" Phillips screws provided in this kit. (Figure A) 2. Slide the aftermarket radio into the radio housing assembly and secure with screws supplied with the radio. (Figure B) 3. Secure the radio housing assembly to the bike using (4) 3/16" Allen screws previously removed in step 8 of disassembly. (Figure C) 4. a. For the Street Glide, Electra Glide, Ultra, (Figure A) (Figure B) (Figure C) and Limited models 2014-up: Attach the radio bracket removed in step 6 of disassembly to the top of the radio housing assembly, and secure with (4) #10-32 x 1/2" Phillips steel machine screws provided in this kit. b. For the Road Glide 2015-up: Attach the fairing bracket removed in step 10 of disassembly to the top of the radio housing assembly, and secure with (4)

  • Page 6: Installation

    SADDLE TRAMP INTERFACE INSTALLATION INTERFACE FEATURES TABLE OF CONTENTS • Provides accessory power (12-volt 10-amp) Installation ..............................6 • Retains balance Connections ...............................7 • Retains handlebar controls: Programming ............................8 • H-D Handlebar controls can be added Troubleshooting ............................9 • 71500248C '14-'20 w/o Traction Control • 71500561 '20-Up w/Traction Control • USB Micro-B updatable INTERFACE COMPONENTS TOOLS REQUIRED • Saddle Tramp Interface: • Cutting tool • Crimping tool • Tape • Connectors (example: butt-connectors, bell caps, etc.) • Circuit board • Housing, cap, and cover • Harness • 3.5mm adapter IMPORTANT NOTE Caution - If the fuse on the aftermarket...

  • Page 7: Connections

    CONNECTIONS Fuse Front Rear View AUX-IN Rear Inside Case Yellow - Battery power Black - Ground Red - Accessory power Orange - Illumination Blue - Power antenna Blue/White - Amp turn on from radio Gray - Front right speaker (+) Vehicles without handlebar controls Gray/Black - Front right speaker (-) 1.

  • Page 8: Programming

    PROGRAMMING 1. Turn the ignition on. 5. The LED light will flash Green & Red while the interface programs the radio to the handlebar controls. Once programmed, the LED light will go out, then produce a pattern which will identify the radio type installed. Green & Red LED 2. Connect the BC-HDR-K1 harness to the wiring harness in the bike. Green or Red LED 6. The LED light will go out, then once again quickly flash Green & Red while the interface programs itself to the vehicle. Once programmed, the LED light will go out again, then turn solid Green. Green & Red LED 3. For vehicles without hand controls: The interface will automatically program. Do Not Touch Green LED 7. Turn the ignition off, then back on. 4.

  • Page 9: Troubleshooting

    TROUBLESHOOTING Final LED Feedback If the interface fails to function you will At the end of programming the LED light will turn Solid Green which indicates programming need to press the reset button. To access Reset Button was successful. If the LED light didn’t turn Solid Green, reference the list below to understand the button remove the cover of the water which programming section the problem may stem from. resistant case, slide out the circuit board and press the reset button. The LED will Radio Vehicle start flashing, starting at step 2, repeat the Programming Programming LED Light programing process. Section Section Solid Green Pass Pass LED Light Slow Red Flash Fail Pass Slow Green Flash Pass Fail Solid Red Fail Fail Note: If the LED light shows Solid Green for Pass (indicating everything programmed correctly), yet the steering wheel controls don’t work, check to ensure that the 3.5mm jack is plugged in, and also plugged into the correct jack on the radio. Once corrected, press the reset button, then program again.
  • Page 10 386.257.1187 MetraOnline.com...
  • Page 11 REV. 11/10/21 INSTBC-HDR-K1...
  • Page 12 BC-HDR-K1 I N S TA L L AT I O N I N S T R U C T I O N S Having difficulties? We’re here to help. Contact our Tech Support line at: 386-257-1187 Or via email at: techsupport@metra-autosound.com Tech Support Hours (Eastern Standard Time) Monday - Friday: 9:00 AM - 7:00 PM Saturday: 10:00 AM - 7:00 PM Sunday: 10:00 AM - 4:00 PM ® NOWLEDGE IS OWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected...