Advertisement
Quick Links
KIT COMPONENTS
• A) Radio housing (with rubber gasket) • B) (4) 1/2" long button-head cap screws • C) Wiring harness (not shown)
• D) ASWC-1 interface in water resistant enclosure (not shown) • E) 44-UA20 antenna (not shown)
A
Metra. The World's Best Kits.
®
Harley-Davidson
1998-2013
(†) Without factory amp, two speaker systems only
Visit
MetraOnline.com
specific applications
KIT FEATURES
• ISO DIN radio provision with pocket
• ASWC-1 interface in water resistant enclosure included to retain
handlebar audio controls
• 44-UA20 antenna included
B
MetraOnline.com
(FL models with a fairing) (†)
for more detailed information about the product and up-to-date vehicle
© COPYRIGHT 2020 METRA ELECTRONICS CORPORATION
99-9613WR
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
- FLH (batwing fairing) ....................................2-3
- Roadglide (sharknose fairing) .....................4-5
Kit Assembly ..........................................................6
Wiring Instructions ................................................7
ASWC-1 Instructions ...............................................7
Final Assembly .......................................................8
Handlebar Control Settings ...............................8-11
WIRING & ANTENNA CONNECTIONS
Wiring Harness: Included
Antenna: 44-UA20 included
Handlebar controls: ASWC-1 in water resistant
enclosure included
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• Socket wrench: (T-25 Torx, T-27 Torx, 1/2", 3/16 hex)
Attention!
Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
REV. 3/6/20 INST99-9613WR
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Metra Electronics 99-9613WR
Summary of Contents for Metra Electronics 99-9613WR
-
Page 1: Table Of Contents
When testing the aftermarket equipment, ensure that all factory equipment is connected before cycling the key to ignition. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 3/6/20 INST99-9613WR... -
Page 2: Fairing Disassembly
FAIRING DISASSEMBLY FLH/Batwing models: 1. Cover the front fender. 2. Remove the (2) T-27 Torx bolts from the inner fairing (under mirrors). Step 4 (Figure A, step 2) 3. Remove the (2) T-27 Torx bolts from the outer edges of the inner fairing near the fork tubes (facing forward). -
Page 3: Flh (Batwing Fairing)
FAIRING DISASSEMBLY (CONT) FLH/Batwing models: (Cont) 6. Lift away and unplug the headlight to remove the outer fairing. (Figure B) 7. Extract the (2) 3/16” Allen bolts from each side of the radio housing. (Figure C) 8. Remove the factory radio. Continue to Kit Assembly (Figure B) (Figure C) -
Page 4: Roadglide (Sharknose Fairing)
FAIRING DISASSEMBLY Roadglide/Sharknose models 1. Loosen the (6) T-25 Torx bolts from the Step 1 Step 1 bottom, middle and top of the left and right sides of the inner fairing. (Figure A) Continued on the next page (Figure A) 1.800.221.0932 MetraOnline.com... - Page 5 FAIRING DISASSEMBLY (CONT) Roadglide/Sharknose models (Cont) 2. Use a 1/2” socket or box wrench to remove the (2) acorn nuts that hold each turn signal at the lower fairing. Let the signals hang loose. (Figure B) 3. Lift away the fairing, unplug the headlights, and then remove.
-
Page 6: Kit Assembly
KIT ASSEMBLY 1. Remove the metal DIN sleeve and trim Optional ring from the aftermarket radio. spacers if 2. Slide the radio into the radio housing needed and secure with the screws supplied with the radio. (Figure A) 3. Insert the radio and kit assembly into the factory radio opening, from the back side of the inner fairing. -
Page 7: Wiring Instructions
WIRING INSTRUCTIONS ASWC-1 INSTRUCTIONS (CONT) From the wiring harness provided to the aftermarket radio: • For the radios listed below: Connect the 3.5mm adapter provided to the male 3.5mm SWC jack. Any remaining wires tape off and disregard. • Connect the Black wire to the ground wire. •... -
Page 8: Final Assembly
FINAL ASSEMBLY HANDLEBAR CONTROL SETTINGS 1. Connect the 44-UA20 (provided), and complete all necessary connections to the radio, but L.E.D. Feedback do not connect the ASWC-1 just yet. The (17) Red L.E.D. flashes represent which brand radio the ASWC-1 is connected to. Each flash 2. - Page 9 HANDLEBAR CONTROL SETTINGS (CONT) Attention: Axxess Updater App can also be used to program the following (3) sub-sections as Radio Legend well, pending that the interface has been initialized and programmed. 1 - Eclipse (Type 1) 6 - Pioneer/Jensen 10 - Clarion 13 - LG (Type 2) 2 - Kenwood...
- Page 10 HANDLEBAR CONTROL SETTINGS (CONT) Remap Buttons 1 - Not allowed 10 - Band The interface has the ability to change the button assignment for the handlebar control buttons, except Volume-Up and Volume-Down. Follow the steps below to remap the 2 - Not allowed 11 - Play/Enter handlebar control buttons.
- Page 11 HANDLEBAR CONTROL SETTINGS (CONT) Dual Assignment (long button press) Dual assignment legend 1 - Not allowed 10 - Band The ASWC-1 has the capability to assign two functions to a single button, except Volume- Up and Volume-Down. Follow the steps below to program the button(s) to your liking. 2 - Not allowed 11 - Play/Enter Note: Seek-Up and Seek-Down come programmed as Preset-Up and Preset-Down for...
- Page 12 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 3/6/20 INST99-9613WR...
Need help?
Do you have a question about the 99-9613WR and is the answer not in the manual?
Questions and answers