Toro 316000001 Operator's Manual
Toro 316000001 Operator's Manual

Toro 316000001 Operator's Manual

42in bagger zero-turn-radius riding mower
Hide thumbs Also See for 316000001:

Advertisement

Quick Links

42in Bagger
Zero-Turn-Radius Riding Mower
Model No. 79391-Serial No. 316000001 and Up

Introduction

Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. You are responsible for
operating the product properly and safely.
Whenever you need service, genuine parts, or
additional information, contact an Authorized Service
Dealer or Customer Service and have the model
and serial numbers of your product ready.
identifies the location of the model and serial numbers
on the product. Write the numbers in the space
provided.
1. Model and serial number location
Model No.
Serial No.
This manual identifies potential hazards and has
safety messages identified by the safety-alert symbol
(Figure
2), which signals a hazard that may cause
serious injury or death if you do not follow the
recommended precautions.
Original Instructions (EN)
Figure 1
Figure 1
This manual uses 2 words to highlight information.
Important calls attention to special mechanical
information and Note emphasizes general information
worthy of special attention.
Proposition 65 Warning
This product contains a chemical
or chemicals known to the State of
California to cause cancer, birth defects,
or reproductive harm.
Contents
Introduction ............................................................... 1
Safety ....................................................................... 2
g005673
Towing Safety ..................................................... 2
Safety and Instructional Decals .......................... 3
Setup ........................................................................ 4
1 Preparing the Machine..................................... 5
2 Installing the Weight......................................... 5
3 Installing the Attachment Mount ....................... 7
4 Installing the Latch Rod...................................11
5 Assembling the Bagger Top ............................11
6 Installing the Bagger Top................................ 12
7 Installing the Chute ........................................ 12
Operation ................................................................ 14
Emptying the Grass Bags ................................. 14
Removing the Bagger ....................................... 15
Using the Draw Bar........................................... 16
Operating Tips ................................................. 17
Maintenance ........................................................... 18
Inspecting the Bagger Attachment .................... 18
Form No. 3399-550 Rev B
Operator's Manual
Figure 2
Safety-alert symbol
WARNING
CALIFORNIA
Printed in the USA
*3399-550* B
All Rights Reserved
g000502

Advertisement

Table of Contents
loading

Summary of Contents for Toro 316000001

  • Page 1: Table Of Contents

    Form No. 3399-550 Rev B 42in Bagger Zero-Turn-Radius Riding Mower Model No. 79391—Serial No. 316000001 and Up Operator's Manual Introduction g000502 Read this information carefully to learn how to operate Figure 2 and maintain your product properly and to avoid Safety-alert symbol injury and product damage.
  • Page 2: Safety

    • Inspecting the Mower Blades ......19 Stop on level ground, disengage drives, chock or Caring for the Grass Bags......... 19 block wheels, shut off the engine and remove the Cleaning the Bagger Attachment ...... 19 key before leaving the operator's position for any Storage ..............
  • Page 3: Safety And Instructional Decals

    Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal109-6809 109-6809 1. Crushing hazard of hand—do not remove the whole bagger from the machine; open the bagger top and then remove the bag(s) from the bagger.
  • Page 4: Setup

    Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. Bolt (3/8 x 1-1/4 inches) Locknut (3/8 inch) Weight mounting bracket, left Weight mounting bracket, right Washers Install the weight.
  • Page 5: Preparing The Machine

    Locate the front bolts on the underside of the frame (Figure 3 Figure Remove the 2 bolts (3/8 x 1 inch) and 2 locknuts (3/8 inch). Retain the locknuts. Preparing the Machine No Parts Required Procedure Park the machine on a level surface. Engage the parking brake.
  • Page 6 Note: For machines with a foot-assist lift pedal, the washers are not used. • For machines with a foot-assist lift pedal, Remove the forward fasteners in the foot-assist lift pedal bracket and secure the bracket using 2 bolts and 2 lock nuts (Figure Note: Use 1 locknut from loose parts and 1...
  • Page 7: Installing The Attachment Mount

    Install a suitcase weight in front of the flat weight (Figure Secure the weights to the weight bracket with a keyed-cross bar (Figure 9). Install the bar and rotate it 90 degrees downward to lock it in place. Once you have installed all the weights and brackets, check that all the fasteners are tight.
  • Page 8 g030494 Figure 10 2015 Model Shown g028174 Figure 12 1. Stabilizer bracket 3. Locknut (5/16 inch) 1. Self-tapping screw (5/16 x 2. Pivot frame 2. Carriage bolt (5/16 x 3/4 3/4 inch) inch) Attach the draw bar decal 1.3 cm (1/2 inch) to Install the pivot frame to the machine frame as the left of the attachment mount (Figure...
  • Page 9 For 2011 through 2014 Models Only Note: The stabilizer bracket is not used on 2011 through 2014 models. Note: For 2011 through 2014 models, the rear-engine guard is optional for this bagger. Install the pivot frame to the machine frame as shown in Figure 15.
  • Page 10 g030499 Figure 18 Left side shown 1. Pivot-frame hole 4. Support rod 2. Washer 5. Existing keyed slot g030497 3. Hairpin cotter 6. Bent, flared end of support Figure 16 1. Self-tapping screw (5/16 x 2. Pivot frame 3/4 inch) Insert the bent ends of the rod into the attachment mount as shown in Figure 18...
  • Page 11: Installing The Latch Rod

    Installing the Latch Rod Parts needed for this procedure: Latch rod Hairpin cotter Procedure Install the latch rod with a hairpin cotter (Figure 19). g033027 Figure 19 1. Hairpin cotter 2. Latch rod g005666 Figure 20 1. Bagger top 3. Screen tab 2.
  • Page 12: Installing The Bagger Top

    Lift the bagger top and install the bags by sliding the bag frame hooks onto the retaining brackets (Figure 22). Installing the Bagger Top Parts needed for this procedure: Grass Bag Upper bagger tube Procedure Install the bagger top to the bagger frame. Rotate the bagger top to align the key holes in the bagger top brackets with the keys in the posts on the bagger frame...
  • Page 13: Installing The Chute

    Installing the Chute Parts needed for this procedure: Chute Procedure g015204 Figure 25 Angle the metal tab at the front of the chute into the slot in the bracket welded to the mower deck (Figure 24). Note: Ensure that the retaining hook on the chute is out of the way so the chute opening mounts flush to the deck.
  • Page 14: Connecting With The Discharge Tube

    Operation Note: Determine the left and right sides of the machine from the normal operating position. Connecting with the WARNING Discharge Tube To avoid personal injury, follow these procedures: Parts needed for this procedure: • Become familiar with all operating and safety instructions in the Operator's Discharge tube Manual for the mower before using this...
  • Page 15: Clearing Obstructions From The Bagger

    Clearing Obstructions from Install the bags by sliding the bag frame hooks onto the retaining brackets (Figure 29). the Bagger Park the machine on a level surface and disengage the blade control switch. Move the motion control levers outward to the neutral lock position, shut off the engine, remove the key, set the parking brake and wait for all moving parts to stop before leaving the...
  • Page 16: Using The Draw Bar

    Using the Draw Bar The bagger support bracket has a draw bar feature that can be used for towing. • Read and understand all the operating instructions of the machine. • When turning, slow down and observe the clearance. • Make wide turns and keep towed equipment clear of the towing vehicle.
  • Page 17: Operating Tips

    Operating Tips CAUTION As the bagger fills, extra weight is added to Tips for Bagging the back of the machine. If you stop and start the machine suddenly on hills, you may lose steering control or the machine may tip. Remembering the Size •...
  • Page 18: Maintenance

    Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Inspect the bagger After the first 10 hours • Clean the bagger Before each use or daily •...
  • Page 19 Inspecting the Mower Storage Blades Storing the Bagger Inspect the mower blades regularly and whenever a Attachment blade strikes a foreign object. If the blades are badly worn or damaged, install new Clean the bagger attachment; refer to Cleaning blades. Refer to your mower or mower Operator's the Bagger Attachment (page 19).
  • Page 20 Notes:...

This manual is also suitable for:

79391

Table of Contents