Subscribe to Our Youtube Channel
Related Manuals for Stanley PP10
Summary of Contents for Stanley PP10
- Page 1 PP10 HYDRAULIC POST PULLER USER MANUAL Safety, Operation and Maintenance © 2014 STANLEY Milwaukie, OR 97267 U.S.A. 59020 4/2024 Ver. 10...
-
Page 3: Table Of Contents
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest certified dealer, call STANLEY at (800) 972-2647 and ask for a Customer Service Representative. PP10 User Manual ◄ 3... -
Page 4: Safety Symbols
Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and maintenance personnel. 4 ► PP10 User Manual... -
Page 5: Safety Precautions
Do not overreach. Maintain proper footing and this manual and any stickers and tags attached to the balance at all times. PP10 before operation. Failure to do so could result in personal injury or equipment damage. • Operator must start in a work area without bystanders. -
Page 6: Tool Stickers & Tags
OPERATION MANUAL. OPERATION MANUAL. TAG TO BE REMOVED ONLY BY TAG TO BE REMOVED ONLY BY TOOL OPERATOR. TOOL OPERATOR. SEE OTHER SIDE SEE OTHER SIDE SAFETY TAG P/N 15875 (Shown smaller then actual size) 6 ► PP10 User Manual... -
Page 7: Hose Types
This hose is not certifi ed non-conductive and must never be used near electrical conductors. HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hose purchased from STANLEY. DO NOT REMOVE THESE TAGS. -
Page 8: Hose Recommendations
HOSE RECOMMENDATIONS 8 ► PP10 User Manual... -
Page 9: Htma / Ehtma Requirements
2000 psi 2000 psi (At the power supply outlet) (172 bar) (138 bar) (138 bar) (138 bar) (138 bar) Note: These are general hydraulic system requirements. See tool specifi cation page for tool specifi c requirements. PP10 User Manual ◄ 9... -
Page 10: Operation
5. Move the control lever from the UP position past the NEUTRAL position to the DOWN position. This releases the jaws (or chain) from the post and lowers the lift frame weldment down to the base weldment (bottom of post). 10 ► PP10 User Manual... -
Page 11: Tool Protection & Care
Ensure that the recommended relief valves are • Always replace hoses, couplings and other parts installed in the pressure side of the system. with replacement parts recommended by STANLEY. • Always check high-pressure couplers for leaks and Supply hoses to the intensifier must have a minimum damage before operating the system at maximum working pressure rating of 2500 psi/175 bar. -
Page 12: Troubleshooting
Provide cooler to maintain proper fluid temperature (140 °F/60 °C max). Check relief valve setting. Eliminate flow control devices. 12 ► PP10 User Manual... -
Page 13: Accessories
Width ..............................14 in/35.5 cm System Type ............................Open Center Note: Weights, dimensions, and operating specifications listed are subject to change without notice. Where specifications are critical to your application, please consult the factory. ACCESSORIES Chain Assembly ..............................17529 PP10 User Manual ◄ 13... -
Page 14: Pp10 Parts Illustration
PP10 PARTS ILLUSTRATION 14 ► PP10 User Manual... -
Page 15: Pp10 Parts List
SEAL KIT (* DENOTES PART IN KIT) 17550 LIFT FRAME WELDMENT 371500 ELASTIC STOP NUT, 1/2-13 HEX Note 1: If you have an older PP10, built prior to 01751 O-RING 3/8 × 9/16 × 3/32 * November 2011, and you are replacing item # 24 06736 CAPSCREW, 5/16-18 ×... - Page 16 STANLEY 3810 SE Naef Road Milwaukie, Oregon 97267 USA (800) 972-2647 / Fax (503) 652-1780...
Need help?
Do you have a question about the PP10 and is the answer not in the manual?
Questions and answers