Table of Contents
Advertisement
Setting up the system
convenient system control operations.
below.
X88 Mode : lets you combine XS, X88, and .X% terminals
(LTB) Mode : for GLTB) terminals only
the instructions in "SWITCHING FROM [SL16] TO [XS81" below.
EXAMPLE:
[XS8] mode connections
The underlined portion represents the setting of the system controi mode
[SL16]
[XS8]
Receiver
MD recorder
Cassette deck
CD player
Record player
[SL16]
SYSTEM
CONTROL
cord
[SL16] [XS] [XS8] [XR]
[SL16] [XS] [XS8]
[XS]
&
8)
cause a malfunction and damage your equipment.
Connecting the system control _.
There are two KENWOOD system control modes. Make connections according to the groups of terminal symbols shown
This unit is compatible with both [XS8] and {SL16] modes. It comes from the factory set to the [SL16] mode. To switch to the [XS8] mode, follow
4OQ80VR (En/K)
Connecting system control cords after connecting
a KENWOOD
audio component system lets you take advantage of
|
EXAMPLE: [SL16] mode connections
The underlined portion represents the setting of the system controi mode
[SL16) [XS8]
Hie
[SL16] [XS] [XS8] [XR]
Sc
cord
[SL16] [XS] [XS8]
[XS]
Record player
¢ In order to take advantage of the system control operations, the components must be connected to the correct jacks. To use a CD player it must
be connected to the CD jacks. To use a cassette deck (or MD recorder) it must be connected to the TAPE/MD jacks. When using more than one
CD player (etc.) only the one connected to the specified jacks may be connected for system control.
«Some CD players and cassette decks are not compatible with the [SL16] system control mode. Be sure to use the [XS8] system control mode
when making system connections with equipment that is not [SL16] compatible.
¢Some MD players are not system contro! compatible. You cannot make system control connections to this kind of equipment.
. {SL16] equipment cannot be combined with [XR], [XS], and [XS8} equipment for system operations. If your
equipment consists of this kind of combination, please do not connect any system control cords. Even without
system control cords, normal operations can be carried out without effecting performance.
2 Do not connect system control cords to any components other than those specified by KENWOOD.
It hayes
& Be sure the system control plugs are inserted all the way in to the system control terminais.
SYSTEM CONTROL OPERATIONS
i Remote
Control
ate tm:s unit witn the system remote supplied with the
i supimene Operation (except [XR] equipment)
>you Start
Diayoack
from asource component, the Input selector
notres
jes sy, tones to that component
automatically
| SyOr anes Recording (except [XR] equipment)
3
J syrorronze
secording
with
the start of playback
when
tram
CO)
MD or analog aiscs
"Registering setup codes for other components"
|
|
|
|
|
I
SWITCHING FROM [SL16] TO [XS8]
You
can
easily change
the system
contro!
mode
by adjusting
the
position of the SYSTEM CONTROL switch on the rear panel.
Do this operation after completing all connections.
For [SL16] SL 76
XS 8
For [xse]
m
* This operation will not effect items stored in the memory.
+ After switching the system control mode, turn the power off and
then on once to confirm the new setting.
Registering setup codes for KENWOOD audio components
¢ Once you finish making the system connections,
be sure to register the appropriate setup code for each component.
~ (36.
* Tyou owr remote controllanle KENWOOD audio components that are not compatible with system control (or cannot be combined with your other
system control components),
registering the setup code enables you to control those components
using the remote control supplied with this
umit (without connecting system control cords).
To register setup codes for your remote controllable KENWOOD
audio components,
see
Advertisement
Table of Contents
