6. Troubleshooting _______________________________________ 25 Thank you for choosing this product. We advise you to carefully read all the instructions contained in this manual, in order to understand how to operate your dishwasher safely and correctly. The manual is divided into paragraphs, which provide a step by step description of the dishwasher functions, with clear instructions accompanied by detailed illustrations.
DESCRIBED ABOVE. THE NAME PLATE FEATURING THE TECHNICAL DATA, SERIAL NUMBER AND MARKINGS IS VISIBLY POSITIONED ON THE INNER EDGE OF THE DOOR. THE NAME PLATE ON THE INNER EDGE OF THE DOOR MUST NEVER BE REMOVED. DO NOT LEAVE THE DISCARDED PACKAGING MATERIALS UNSUPERVISED WITHIN THE HOME. SEPARATE THE VARIOUS MATERIALS WHICH MAKE UP THE PACKAGING AND TAKE THEM TO THE NEAREST SORTED WASTE COLLECTION CENTRE.
IN MODELS EQUIPPED WITH THE AQUSTOP DEVICE, THERE IS A SOLENOID VALVE INSIDE THE WATER INTAKE HOSE. DO NOT CUT THE HOSE AND DO NOT ALLOW THE SOLENOID VALVE TO DROP INTO WATER. IN THE EVENT OF DAMAGE TO THE WATER INTAKE HOSE, DISCONNECT THE APPLIANCE FROM THE ELECTRICAL POWER SUPPLY AND FROM THE WATER SUPPLY.
Water supply connection Preventing the risk of clogging or damage: if the water pipe is new or has not been used for a long time, before connecting to the water supply check that the water is clear and free of impurities, to prevent damage to the appliance.
Installation instructions The dishwasher can also be connected to a hot water supply not exceeding 60°C. Supplying the appliance with hot water cuts down the washing time by approximately 20 minutes, but slightly reduces its effectiveness. Make the connection to the domestic hot water supply using the same procedure described for connecting to the cold water supply.
NO RINSE AID LIGHT (on some models only) RECESSED DOOR HANDLE LIGHTING When the ON/OFF button (1) is pressed, the dishwasher switches on and the light (6) comes on. About 2 seconds later, the PROGRAM PHASES lights (10) will come on. PROGRAMMING In this model of dishwasher, all programming procedures can only be carried out with the door closed.
Page 8
The HALF LOAD option (4) is available for all programs except the soak program. Reference program as AS/NZS 2007 is P2+P1 ( GLASS (-) Not present. The washing cycle will not take place if the dishwasher door is left open or not properly closed.
Page 9
To start the appliance, simply press the START/PAUSE button (5) for a few seconds, the PROGRAM PHASES lights (10) will go out until the light of the first phase of the selected program start flashing (confirmation buzzer). This phase, that updates itself during the cycle, is “indicative”...
Page 10
User instructions At this point the PROGRAM PHASES lights (10) will illuminate as the program progresses, indicating the point reached in the washing procedure: Prewash Wash Rinse The light of the phase in progress will flash, and will remain constantly on while heating is in progress.
Now press buttons P1+P2 simultaneously and the first three program lights will come on. In case that the door is opened during the operation, to the next door closing it is going to be necessary to start the program as shown in paragraph “ S ”.
Page 12
At the end of the washing program, wait at least 20 minutes before removing the dishes, to allow them to cool down. To prevent any water droplets on the upper basket from falling on the dishes in the lower basket, it is advisable to unload the lower basket first, and then the upper basket.
Before replacing the cap, remove any salt residues from around the opening. When using the dishwasher for the first time, in addition to the salt it is also necessary to add •...
Page 14
User instructions ADJUSTING THE WATER SOFTENING SYSTEM The dishwasher is equipped with an device for the user to adjust the water softening system according to the hardness of the water supply. According to the machine model, the selector which acts on the adjustment may be located: inside the plastic locking ring located on the right-hand side, inside the dishwasher;...
The amount of rinse aid must be increased if the washed dishes appear dull or feature circular • stains. If, on the other hand, the dishes are sticky or have white streaks, it is necessary to reduce the • rinse aid setting.
If performance problems (e.g. a white coating on the tank or dishes, poor drying, dirt on dishes at the end of the wash) are noted, users are advised to return to conventional products (granular salt, powder detergent and liquid rinse aid). However,...
For optimum use of space, the bottom basket is fitted with two plate supports which can be laid flat if there are no plates to be loaded. It also has a "tip-up support" (with one or two sectors depending on models) for small plates; to take small plates, it must be positioned as shown in the illustrations.
Page 19
The cutlery should be arranged in an orderly manner inside the basket, with the handles pointing downwards. Take care during loading to avoid injury from the knife blades. The basket is suitable for all types of cutlery, except those long enough to interfere with the upper spray arm.
Page 20
Load plates facing forward; cups, bowls etc. must always be facing downwards. The left-hand side of the basket can be loaded with two layers of cups and glasses. In the centre section, plates and saucers can be loaded vertically into the supports provided.
Clean the door gaskets with a damp sponge. Periodically (once or twice a year) it is advisable to clean the tank and gaskets, using a soft cloth and water to remove any deposits.
D from the underside to remove it from the micro-filter: • separate the two parts which make up the plastic filter by pressing the body of the filter in the • zone shown by the arrows;...
Certain detergents can be more • corrosive than others. check that the cap of the salt container is securely closed, and that the water softening setting • is correct. If after following the above troubleshooting instructions the problem persists, call the nearest After- Sales Centre.
User instructions 6. Troubleshooting In case of a malfunction, the dishwasher will identify the program by switching on a combination of lights. When an alrm is present, all the PROGRAM lights (7) come on, while the PROGRAM PHASES lights (10) identify the error code:...
Page 25
Free standing from 850 mm to 870 mm Semi-integrated from 820 mm to 870 mm Capacity 14 Standard place settings Water supply pressure min. 50 – max. 900 KPa (min. 0.5 – max. 9 bar) Electrical characteristics See rating plate...
Page 26
Solo su alcuni modelli Certain models only Seulement sur certains modèles nur bei einige Modellen Sólo en algunos modelos alleen indien van toepassing 820- 820- 1/2” S N SF 3x16 3/4” 0,3-10 bar 0,3-10 bar 0,3-10 bar 0,3-10 bar 1,14 m...
Page 27
Regolazione vite tensione molle (11) - Copertura foto con tappo in dotazione (12) Door spring Adjustement device (11) - Covering of hole using cap provided (12) Réglage des ressorts de la porte (11) - Couverture du trou avec le bouchon fourni (12) Vorrichtung für die Einstellung der Spannung der Türfedem (11) -...