Advertisement
Quick Links
ASSEMBLY AND INSTALLATION
T0578 / T0579
WARNING:
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
Hardware Package (
AA
Cross Bar Unit
X1
Important to Know
1. Read all instructions carefully before installation and operation.
2. If you are not familiar with state and local electrical codes, it is
recommended that you consult with a qualified electrician.
3. Before installation, shut off power at the main fuse or circuit
breaker box. Be aware that simply turning off the wall switch is
not sufficient to prevent an electrical shock.
4. This fixture requires a 120 VAC, 60 Hz power source.
5. Do not attempt to take the lantern apart; there are no
serviceable parts inside.
6. To avoid sensor damage by lightning or electrical surge, make
sure the grounding wire is securely connected.
7. For general safety and to avoid any possible damage to the
sensor, be sure the power is switched "off" before replacing the
bulb.
8. Compatible with LED dimmable bulb.
Maximum Wattage: 60W
Dimmable Bulb
Work Temperature: -4°F~104°F
Installation Steps
Turn off the power at fuse or circuit box.
1. Unscrew the two bolt nuts (DD).
Remove the two rubber pads
(EE) and the cross bar unit (AA)
from the backplate.
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
):
included
BB
Mounting Screw
X2
Incandescent
Bulb or 20W LED
1
Backplate
EE
AA
DD
CC
Wire Connector
X3
Features
1. Energy saving fixture.
2. Use dim-to-full brightness where dim-illumination
is preferred, such as your front entrance. Use
off-to-full brightness where off/on illumination is
preferred, such as your backyard.
3. When in manual override mode, use wall switch
to keep the light ON till dawn.
2. Attach the cross bar unit (AA) to
the outlet box by using two
mounting screws (BB). Adjust
the length of the preinstalled
headless screws if necessary.
Note: Make sure that the
headless screws are lined
up horizontally to make the
fixture level.
Page 1 of 5
DD
EE
Bolt Nut
X2
2
200313
Rubber Pad
X2
Outlet Box
BB
AA
Headless Screw
Advertisement
Related Manuals for Vaxcel ELEMENTS T0578
Summary of Contents for Vaxcel ELEMENTS T0578
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0578 / T0579 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS. Hardware Package ( included Cross Bar Unit...
- Page 2 4. Pull out the source wires from 3. Attach the decorative cup (GG), the outlet box. Make wire rubber pad (HH) to main fixture connections using wire by inserting the threaded pipe, connectors (CC) as follows: then secure it with a finial (FF). •...
-
Page 3: Functions And Operations
FUNCTIONS AND OPERATIONS Choose a mode by sliding the switch at the back of sensor lens. When power is first applied, the light will turn on immediately. Wait for 30 seconds to allow the sensor to warm up. 1. Test MODE (daytime and nighttime operation.) •... - Page 4 NOTE: Where you install your lantern is important: 1. The sensitivity of the motion sensor will increase as the Be sure the light is mounted straight on the wall; environmental temperature gets cooler. For best performance, otherwise, the detection distance may be limited. gently clean the lens with a soft cloth every 1 or 2 months to assure maximum sensitivity.
-
Page 5: Troubleshooting
TROUBLESHOOTING Refer to following information to solve your problems. SOLUTION DAY/NIGHT SYMPTOM POSSIBLE CAUSE Slide switch is not set in the test Set the slide switch in the test mode for testing. mode. Wall switch or circuit breaker is off. Turn on wall switch or circuit breaker.