EINHELL TC-TS 2025/2 U Original Operating Instructions page 26

6. Assembly
Danger! Pull out the power plug before carry-
ing out any maintenance, resetting or assem-
bly work on the circular saw!
6.1 Assembling the base frame (Fig. 3-4)
Danger! Make allowance for the weight of the
machine and arrange another person to help you
if necessary!
•
Turn the bench-type circular over and set the
saw down on the floor or on some other work
surface. Important! Place suitable material
(e.g. packaging material) between the table
surface and the surface on which it is stood to
prevent any damage to the table surface.
•
Important! Only fasten all the screw connec-
tions between the base frame and machine
loosely at first. Wait until you have returned
the bench-type circular saw to its working po-
sition before tightening the screw connections
securely. This is so that you can be sure the
base frame is aligned level with the surface
on which it is stood.
•
Use the hexagon screws (43) to fasten the
four legs (29) loosely to the saw.
•
Then, using the hexagon screws (43) and the
nuts (44), fasten the longitudinal struts (31)
and the cross-struts (30) loosely to the legs.
Make sure that the shorter struts (30) are fas-
tened to the side of the saw.
•
Plug the rubber feet (13) onto the legs (29).
6.2 Assembling the table width extension
(Fig. 5, 6)
•
Use the hexagon screws (43) and the nuts
(44) to fasten the table width extensions (49)
loosely to the saw table (1) at position (a).
•
Fit the tubular braces (50) to the table width
extensions (49) and secure them loosely to
the saw table (1) with the hexagon screws
(43).
•
Insert the struts (47, 48) between the tubular
brace (50) and table width extension (49) and
secure them loosely with the hexagon screw
(43).
•
Important! The struts for the left and right-
hand sides are different in length. You there-
fore have to fit the long struts (47) on the left-
hand side of the saw table (1) and the short
struts (48) on the right-hand side.
Anl_TC_TS_2025_2_U_SPK13.indb 26 Anl_TC_TS_2025_2_U_SPK13.indb 26
GB
•
Remove the hexagon screws (43) from the
legs (29) on the left and right-hand side of the
saw to enable the struts (47, 48) to be fitted to
the base frame.
•
Fasten the struts (47, 48) loosely to the legs
(29) with hexagon screws (43), but do not
tighten.
•
Align the table width extensions (49) level
with the saw table (1).
•
Then tighten the screw connections referred
to in 6.2. Use both the wrenches (38) and (39)
to do this.
6.3 Standing the bench-type circular saw up-
right (Fig. 2, 7-9)
•
Turn the machine over so that it stands on its
legs.
•
The bench-type circular saw must be stood
on a flat surface.
•
Then tighten all loose screw connections. Use
both the wrenches (38) and (39) to do this.
•
Screw the additional legs (37) to the rear legs
(29) so that they point towards the rear of the
machine. Use the hexagon screws (43) and
the nuts (44) to fasten them.
•
Warning! Don not fit the additional legs (37)
too far away from the surface on which the
machine stands; they are intended to provide
protection against tipping over.
•
Fit the socket head screw (45) with the two
nuts (46) to the front right leg (29). This is
used as a holder for the push stick (3).
•
To enable the machine to be used with the
suction hose (10), the cap (36) on the saw
blade guard (2) must be removed first. To
do this, undo the screw using a crosstip
screwdriver.
•
Then connect the saw blade guard (2) and
the side connection of the extractor adapter
on the housing (16) to the suction hose (10).
•
A crosstip screwdriver and hex key are not
supplied with the product.
6.4 Changing the table insert (Fig. 10, 12)
•
To prevent increased likelihood of injury, the
table insert should be changed whenever it is
worn or damaged.
•
Take off the saw blade guard (2) (see 6.6).
•
Remove the countersunk head screw (17).
•
Take out the worn table insert (6).
•
Fit the replacement table insert by following
the above in reverse.
- 26 -
17.10.2023 08:59:33 17.10.2023 08:59:33