Page 1
THINKLITE TTL CAMERA FLASH 迅 机 光 合格证 QC PASS 说 明 手 册 Instruction Manual 在使用本产品之前: 请先仔细阅读本手册, 以确保您能安全使用。 请保存好本手 箱 册以备将来查询参考。 Before using this product: Please read this user manual carefully in order to ensure your safety and the proper operation of this product. Keep for future reference.
Contents Foreword Thank you for purchasing this product. Foreword This TT685IIN camera flash applies to Nikon series cameras and Warning is compatible with i-TTL II autoflash. With this i-TTL compatible Name of Parts flash, your shooting will become simpler. You can easily achieve a...
Name of Parts ● LCD Panel (1)i-TTL Autoflash Zoom : zoom display ② Focus length ① : Automatic : High-speed sync : Manual i-TTL : i-TTL autoflash ⑨ ③ ⑦ Distance indicator ④ display ⑤ ⑩ ⑥ Flash exposure Effective compensation amount Flash Range ●The display will only show the settings currently applied.
● Rotate the hotshoe fixing buckle to the right until it locks up. SYNC Detach the Camera Flash. ● What’s in the Box of TT685IIN Kit? ● Press the button and rotate the hotshoe fixing buckle to the left until it is loosened.
Flash Mode—i-TTL Autoflash High-Speed Sync High Speed Sync (FP flash) enables the flash to synchronize with all camera shutter speeds. This is convenient when you want to use This flash has three flash modes: i-TTL, Manual (M), and RPT aperture priority for fill-flash portraits. (Stroboscopic).
M: Manual Flash RPT: Stroboscopic Flash The flash output is adjustable from 1/1 full power to 1/256th power With stroboscopic flash, a rapid series of flashes is fired. It can be in 1/10th stop increments. To obtain a correct flash exposure, use used to capture a multiple images of a moving subject in a single a hand-held flash meter to determine the required flash output.
TT685IIN that is wirelessly controlled is called the receiver unit. ● You can also wirelessly control the TT685IIN set as the receiver unit with the transmitter X1T-C (sold separately). For details on setting the transmitter unit functions, see the transmitter’s instructions.
If there are other wireless flash systems nearby, you can change Transmitter Unit Setting the channel IDs to prevent signal interference. The channel IDs of ●Attach a TT685IIN camera the Transmitter unit and the Receiver unit(s) must be set to the flash on the camera and set same.
6. M: Wireless Flash Shooting with Manual Flash Check the flash operation. ● Press the Transmitter This describes wireless (multiple shooting) using manual flash. unit’s Test Button < >. You can shoot with a different flash output setting for each ●...
The Reason & Solution of Not Triggering in Godox 2.4G -7-120° Wireless 1. Disturbed by the 2.4G signal in outer environment (e.g. wireless 330° base station, 2.4G wifi router, Bluetooth, etc.) → To adjust the channel CH setting on the flash trigger (add 10+ channels) and use the channel which is not disturbed.
1. Press<MENU> Button until C.Fn menu is displayed. The “Ver x.x” If you set the flash coverage manually, make sure it covers in the top-right corner refers to the software version. the lens focal length so that the picture will not have a dark 2.
→Attach the camera’s mounting foot securely to the camera. ● The electrical contacts of the Camera Flash and camera are dirty. →Clean the contacts. Model TT685IIN Compatible Cameras Nikon cameras The power turns off by itself. Guide No.(1/1 output, 200mm) GN≈60 (ISO100)
●As the firmware upgrade needs the support of Godox G3 software, please download and install the "Godox G3 firmware Note: This equipment has been tested and found to comply with the upgrade software"...
Need help?
Do you have a question about the TT685IIN and is the answer not in the manual?
Questions and answers