Advertisement
Quick Links
ASSEMBLY AND INSTALLATION
T0254 / T0255 / T0256 / T0257
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. Read and save these instructions.
Important to Know
1. Read all instructions carefully before installation and
operation.
2. If you are not familiar with state and local electrical codes,
it is recommended that you consult with a qualified
electrician.
3. Before installation, shut off power at the main fuse or
circuit breaker box. Be aware that simply turning off the
wall switch is not sufficient to prevent an electrical shock.
4. This fixture requires a 120 VAC, 60 Hz power source.
5. Do not attempt to take the lantern apart; there are no
serviceable parts inside.
6. To avoid sensor damage by lightning or electrical surge,
make sure the grounding wire is securely connected.
7. For general safety and to avoid any possible damage to
the sensor, be sure the power is switched "off" before
replacing the bulb.
8. Compatible with LED dimmable bulb.
Maximum Wattage: 60W Incandescent Bulb or 20W
Dimmable LED Bulb.
Work Temperature: -4°F~104°F
Wire Nut (E)
Outlet Box
House Grounding Wire
Headless Screw (D)
Fixture Grounding Wire
Cross Bar (A)
Green Grounding Screw (C)
Mounting Screw (B)
Lock Nut (F)
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Fixture Wire
Page 1/4
Features
1. Energy saving fixture.
2. Use the dim-to-bright illumination option where
you want some minimum illumination through out
the night, such as at your front entrance or garage
door. Use the dark-to-bright illumination option
where you do not need minimum brightness, such
as the backyard or back porch.
3. When in manual override mode, use wall switch
to keep the light ON till dawn.
Hardware Package (included):
Mounting Screw (B)
Cross Bar (A)
Lock Nut (F)
Wire Nut (E)
Back plate
Green Grounding
Screw (C)
Rubber Pad (H)
Ball Nut (G)
Fixture
Small Ball Nut
Ball Nut (G)
Rubber Pad (H)
Type A Max. 60W Bulb OR
Max. 20W Dimmable LED Bulb
(not include)
(not include)
161107
Advertisement
Related Manuals for Vaxcel T0254
Summary of Contents for Vaxcel T0254
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0254 / T0255 / T0256 / T0257 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
- Page 2 Installation steps Turn off the power at fuse or circuit box. Thread two headless screws through the cross bar, and then secure them with four lock nuts (two on each side of the cross bar). Adjust the length of the headless screws if necessary. Note: Make sure that the headless screws are lined up horizontally to make the fixture level.
- Page 3 FIG.2 FIG.1 On the back of the sensor Time Low Level Sens Turn wall switch OFF-ON in 3 Seconds Manual AUTO Mode Override Mode Turn wall switch OFF-ON Test 3H 6H in 3 Seconds again CUSTOMIZATION OPTIONS: Shut-off Delay The Shut-off delay is the length of time the light will stay at high-level brightness after motion has ceased to be detected.
- Page 4 3. Make sure the bulb is medium base bulb or Led dimmable bulb. The following parts are available for re-order if damaged or missing. Spare Parts List: Mounting Hardware 5418MM (1 SET) for T0254 / T0256 5419MM (1 SET) for T0255 / T0257 Green Grounding Mounting Screw (B)