DeWalt DCG409VSX1 Original Instructions Manual page 17

Table of Contents

Advertisement


WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
Proper Hand Position (Fig. K)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the main handle 
and the other hand on the auxilliary handle 
Switches

CAUTION: Hold the auxiliary handle and body of the
tool firmly to maintain control of the tool at start up and
during use and until the wheel or accessory stops rotating.
Make sure the wheel has come to a complete stop be fore
laying the tool down.
nOTE: To reduce unexpected tool movement, do not switch the
tool on or off while under load conditions. Allow the grinder to
run up to full speed before touching the work surface. Lift the
tool from the surface before turning the tool off. Allow the tool
to stop rotating before putting it down.
Slider Switch (Fig. A)
DCG409VS

WARNING: Before connecting the tool to a power supply,
be sure the slider switch is in the off position. Ensure the
slider switch is in the off position after any interruption
in power supply to the tool, such as the activation of a
ground fault interrupter, throwing of a circuit breaker,
accidental unplugging, or power failure. If the slider switch
is locked on when the power is connected, the tool will
start unexpectedly.
To start the tool, slide the ON/OFF slider switch 
front of the tool. To stop the tool, release the ON/OFF slider
switch.
For continuous operation, slide the switch toward the front of
the tool and press the forward part of the switch inward. To stop
the tool while operating in continuous mode, press the rear part
of the slider switch and release.
Variable Speed Dial (Fig. A)
The variable speed dial 
offers added tool control and enables
 9 
the tool to be used at optimum conditions to suit the accessory
and material.
Turn the variable speed dial 
the dial upward for higher speed and downward for
lower speed.
Spindle Lock (Fig. A)
The spindle lock button 
 2 
from rotating when installing or removing wheels. Operate
the spindle lock only when the tool is turned off, the battery is
removed and has come to a complete stop.
, as shown in Fig. K.
 4 
toward the
1
to the desired level. Turn
 9 
is provided to prevent the spindle
NOTICE: To reduce the risk of damage to the tool, do
not engage the spindle lock while the tool is operating.
Damage to the tool will result and attached accessory
may spin off possibly resulting in injury.
To engage the lock, depress the spindle lock button and rotate
the spindle until you are unable to rotate the spindle further.
Surface Grinding, Sanding and Wire
Brushing (Fig. L)

CAUTION: Always use the correct guard per the
instructions in this manual.
 23 
To perform work on the surface of a workpiece:
1. Allow the tool to reach full speed before touching the tool
to the work surface.
2. Apply minimum pressure to the work surface, allowing
the tool to operate at high speed. Material removal rate is
greatest when the tool operates at high speed.
3. Maintain an appropriate angle between the tool and work
surface. Refer to the chart according to particular function.
Function
Grinding
Sanding with Flap Disc
Sanding with Backing Pad
Wire Brushing
4. Maintain contact between the edge of the wheel and the
work surface.
If grinding, sanding with flap discs, or wire brushing,
move the tool continuously in a forward and back
motion to avoid creating gouges in the work surface.
If sanding with a backing pad, move the tool constantly
in a straight line to prevent burning and swirling of
work surface.
nOTE: Allowing the tool to rest on the work surface without
moving will damage the workpiece.
5. Remove the tool from work surface before turning tool off.
Allow the tool to stop rotating before laying it down.

CAUTION: Use extra care when working over an edge, as
a sudden sharp movement of grinder may be experienced.
Precautions To Take When Working on a Painted
Workpiece
1. Sanding or wire brushing of lead based paint is NOT
RECOMMENDED due to the difficulty of controlling the
contaminated dust. The greatest danger of lead poisoning is
to children and pregnant women.
2. Since it is difficult to identify whether or not a paint contains
lead without a chemical analysis, we recommend the
following precautions when sanding any paint:
Personal safety
1. No children or pregnant women should enter the work area
where the paint sanding or wire brushing is being done
until all clean up is completed.
2. A dust mask or respirator should be worn by all persons
entering the work area. The filter should be replaced daily or
English
Angle
20˚-30˚
5˚-10˚
5˚-15˚
5˚-10˚
15

Advertisement

Table of Contents
loading

This manual is also suitable for:

Dcg409vs

Table of Contents