ECO2 Systems SANCO2 GS5-45HPC-D Installation Manual page 23

Adjust set block out start time Adjust set block out start time
Press Up or Down key and '00' (start time) in '00XX' starts flashing and 'XX' (end Press Up or Down key and '00' (start time) in '00XX' starts flashing and 'XX' (end
time) illuminates. Now the block out start time can be adjusted. Setting can be time) illuminates. Now the block out start time can be adjusted. Setting can be
performed only in hour increments, not in minutes. performed only in hour increments, not in minutes.
Set block out start time Set block out start time
Press the Enter key to set the desired time setting. After the start time is set, the Press the Enter key to set the desired time setting. After the start time is set, the
start time display stops flashing. The end time display starts flashing at the same start time display stops flashing. The end time display starts flashing at the same
time. time.
Adjust block out end time Adjust block out end time
Set to the desired end time by using Up and Down keys. Setting can be performed Set to the desired end time by using Up and Down keys. Setting can be performed
only in hour increments, not in minutes. only in hour increments, not in minutes.
Set block out end time Set block out end time
Press enter key to adjust the desired time setting. After the end time is set, then it Press enter key to adjust the desired time setting. After the end time is set, then it
starts to display 'bo' and '00XX' (00 = start time, XX = end time) by turns. starts to display 'bo' and '00XX' (00 = start time, XX = end time) by turns.
Go back to clock display mode Go back to clock display mode
Hold down Enter key to go back to the clock display mode. It will automatically go Hold down Enter key to go back to the clock display mode. It will automatically go
back to the clock display mode when no panel operation is performed for more back to the clock display mode when no panel operation is performed for more
than 60 seconds. Block out time setting mode cannot be set unless the end time than 60 seconds. Block out time setting mode cannot be set unless the end time
setting is confirmed. setting is confirmed.
Cancel block out setting Cancel block out setting
To cancel the block out setting, set both start and end times to the same time.
To cancel the block out setting, set both start and end times to the same time. To cancel the block out setting, set both start and end times to the same time.
※ ※ Example setting ※ ※ Example setting
※ ※ Example setting
Bo Setting For Example " 13 01 " Bo Setting For Example " 13 01 "
Bo Setting For Example " 13 01 "
AM AM
AM
○ ○
○
To bypass the Block Out Time, simply press the UP key to access the next parameter in
the Commissioning menu
Communication Setting
Error History
Enter into Commissioning Mode
Enter into Commissioning Mode
First option is the Heat Setting
First option is the Heat Setting
Second option is Block Out Time -
Second option is Temperature Setting
Press the UP Key to access Communication Setting then Press Enter to access
Third option is Block Out Time –
Use UP/DOWN arrow keys to toggle between Modbus Off and Modbus On
Press the UP Key to access Error History then Press Enter to access
Press Enter to comfirm choice
This records all errors that have occurred on the system, this can be used for
To bypass the Communication Setting simply press the UP key to access the next
troubleshooting after an error code has been cleared by cycling the power to the unit.
parameter in the Commissioning menu
The most recent error code is displayed first, previous error codes can be seen by
pressing the DOWN key
To bypass the Error History simply press the UP key to access the next parameter in the
Commissioning menu
17 08
PM PM
PM
○ ○
○
13 13 17
13
Unit will not Run Unit will not Run
Unit will not Run
Sanden Heat Pump – Installation Manual Sanden Heat Pump – Installation Manual
Page 16 of 32 Page 16 of 32
SANCO Heat Pump – Installation Manual
2
Page 23 of 44
AM AM
AM
○ ○
○
08 01 01
01