Commissioning Mode; How To Switch To Commissioning Mode - ECO2 Systems SANCO2 GS5-45HPC-D Installation Manual

Heat pump water heater with natural refrigerant(co2)
Hide thumbs Also See for SANCO2 GS5-45HPC-D:
Table of Contents

Advertisement

Commissioning Mode

Commissioning mode is a function to check the heat pump unit status and to check and
perform other settings. It should generally be assumed that the owner does not operate
Commissioning Mode
this function. The following modes can be found in this mode.
Commissioning mode is a function to check the heat pump unit status and to check and
Heat setting mode
perform other settings. It should generally be assumed that the owner does not operate
Commissioning Mode
Set the heating mode to either ON (Unit Runs) or OFF (Unit cannot operate)
this function. The following modes can be found in this mode.
Commissioning mode is a function to check the heat pump unit status and to check and
Outlet water temperature setting mode
perform other settings. It should generally be assumed that the owner does not operate
Heat setting mode
this function. The following modes can be found in this mode.
Set the Outlet Hot water temperature 130~175°
Set the heating mode to either NOR (Unit Runs) or OFF (Unit cannot operate)
Set the heating mode to either ON (Unit Runs) or OFF (Unit cannot operate)
Commissioning Mode
Heat setting mode
Block out time setting mode (Time of use)
Outlet water temperature setting mode
Set the heating mode to either ON (Unit Runs) or OFF (Unit cannot operate)
Set the block out time
Commissioning mode is a function to check the heat pump unit status and to check and
Set the Outlet Hot water temperature 130~175°
perform other settings. It should generally be assumed that the owner does not operate
Outlet water temperature setting mode
Communication setting mode
Error history display mode
this function. The following modes can be found in this mode.
Block out time setting mode (Time of use)
Check the history of any errors that may have occurred.
Set the Outlet Hot water temperature 130~175°
Modbus connection setting
Set the block out time
Heat setting mode
Modbus ID setting mode
Parameter display mode
Block out time setting mode (Time of use)
Set the heating mode to either ON (Unit Runs) or OFF (Unit cannot operate)
Error history display mode
Check the values measured by the thermistors in the unit.
Set the Modbus ID
Set the block out time
Check the history of any errors that may have occurred.
Outlet water temperature setting mode
Error history display mode
Parameter display mode
Set the Outlet Hot water temperature 130~175°
Check the history of any errors that may have occurred.
Check the values measured by the thermistors in the unit.

How to switch to Commissioning Mode

Block out time setting mode (Time of use)
Press and hold down the Up and Down keys together to enter the Commissioning mode.
Parameter display mode
Set the block out time
Check the values measured by the thermistors in the unit.
How to switch to Commissioning Mode
After the mode is selected, press the Enter key to select an option mode from the six
Error history display mode
described above.
Air bleeding mode
Press and hold down the Up and Down keys together to enter the Commissioning mode.
Check the history of any errors that may have occurred.
Set the air bleeding mode
How to switch to Commissioning Mode
To exit Commissioning maintenance mode, either press and hold down the Enter key, or
After the mode is selected, press the Enter key to select an option mode from the six
Parameter display mode
do not touch the control panel for more than 60 seconds so it goes to sleep.
Press and hold down the Up and Down keys together to enter the Commissioning mode.
described above.
Check the values measured by the thermistors in the unit.
After the mode is selected, press the Enter key to select an option mode from the six
To exit Commissioning maintenance mode, either press and hold down the Enter key, or
described above.
do not touch the control panel for more than 60 seconds so it goes to sleep.
How to Switch to Commissioning Mode
How to switch to Commissioning Mode
To exit Commissioning maintenance mode, either press and hold down the Enter key, or
Press and hold down the Up and Down keys together to enter the Commissioning mode.
do not touch the control panel for more than 60 seconds so it goes to sleep.
After the mode is selected, press the Enter key to select an option mode from the six
described above.
To exit Commissioning maintenance mode, either press and hold down the Enter key, or
do not touch the control panel for more than 60 seconds so it goes to sleep.
Sanden Heat Pump – Installation Manual
Page 19 of 40
Sanden Heat Pump – Installation Manual
SANCO
Heat Pump – Installation Manual
Page 19 of 40
2
Page 21 of 44
Sanden Heat Pump – Installation Manual
F
F
F
F
seven

Hide quick links:

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SANCO2 GS5-45HPC-D and is the answer not in the manual?

Subscribe to Our Youtube Channel

Table of Contents

Save PDF