Installation Details - ECO2 Systems SANCO2 GS5-45HPC Owner's Manual

Installation Details

Installation details
Installation details
This Sanden SANCO₂ Heat Pump Water Heater System must be installed by licensed
personnel in accordance with local building codes:
This Sanden SANCO₂ Heat Pump Water Heater System must be installed by licensed
personnel in accordance with local building codes:
Installing contractor should be licensed by applicable state/province and municipal
Installing contractor should be licensed by applicable state/province and municipal
 
authorities to install an Electrical & Plumbing product.
authorities to install an Electrical & Plumbing product.
Installing contractor should be licensed by applicable state/province and municipal

authorities to install an Electrical & Plumbing product.
The unit has been designed for heating potable domestic hot water. Any other The unit has been designed for heating potable domestic hot water. Any other


usage, such as use for DHW in combination with space heating requires both a usage, such as use for DHW in combination with space heating requires both a
The unit has been designed for heating potable domestic hot water. Any other

heat exchanger suitable for local codes to be installed on the system to separate heat exchanger suitable for local codes to be installed on the system to separate
usage, such as use for DHW in combination with space heating requires both a
potable and non-potable water and consultation with Sanden. potable and non-potable water and consultation with Sanden.
heat exchanger suitable for local codes to be installed on the system to separate
Installation details
potable and non-potable water and consultation with Sanden.
The unit is designed to operate when connected to the water supply with a The unit is designed to operate when connected to the water supply with a
 
maximum operating pressure of 95PSI (655 kPa). To ensure the mains pressure maximum operating pressure of 95PSI (655 kPa). To ensure the mains pressure
This Sanden Eco Hot water Heat Pump System must be installed by licensed personnel in
The unit is designed to operate when connected to the water supply with a

does not exceed this, first check incoming cold water mains pressure, and then a does not exceed this, first check incoming cold water mains pressure, and then a
accordance with local building codes:
maximum operating pressure of 95PSI (655 kPa). To ensure the mains pressure
pressure regulating device must be connected to the water supply line. pressure regulating device must be connected to the water supply line.
does not exceed this, first check incoming cold water mains pressure, and then a
Water mains pressure is above 75 PSI.
 Installing contractor should be licensed by applicable state/province and municipal
pressure regulating device must be connected to the water supply line.
authorities to install an Electrical & Plumbing product.
 
Installation of a temperature tempering device is MANDATORY to avoid potential Installation of a temperature tempering device is MANDATORY to avoid potential
The unit has been designed for heating potable domestic hot water and any other


scalds and burns. scalds and burns.
usage, such as space heating requires a heat exchanger suitable for local codes to Installation of a temperature tempering device is MANDATORY to avoid potential
be installed on the system to separate potable and non-potable water.
scalds and burns.
The unit must be stored and transported in an upright position. Failure to do so may The unit must be stored and transported in an upright position. Failure to do so may


render the unit faulty. Such failure is not covered under any warranty agreements. render the unit faulty. Such failure is not covered under any warranty agreements.
The unit is designed to operate when connected to the water supply with a
The unit must be stored and transported in an upright position. Failure to do so may


maximum operating pressure of 95PSI (655 kPa). To ensure the mains pressure
render the unit faulty. Such failure is not covered under any warranty agreements.
Failure to comply with the above conditions will void the warranty. Failure to comply with the above conditions will void the warranty.
does not exceed this, first check incoming cold water mains pressure, and then a
Failure to comply with the above conditions will void the warranty. pressure regulating device must be connected to the water supply line.
California Proposition 65 WARNING

This product contains chemicals known to the State of California to cause
Installation of a temperature tempering device is MANDATORY to avoid potential
cancer, birth defects or other reproductive harm.
scalds and burns.
The unit must be stored and transported in an upright position. Failure to do so may

render the unit faulty. Such failure is not covered under any warranty agreements.
Failure to comply with the above conditions will void the warranty.
75PSI (520 kPa).
This system delivers hot water exceeding 120 This system delivers hot water exceeding 120
This system delivers hot water exceeding 120
This system delivers hot water exceeding 120
Sanden Heat Pump – Installation Manual Sanden Heat Pump – Installation Manual
SANCO Heat Pump – Owner's Manual
Page 4 of 40
2
Sanden Heat Pump – Installation Manual
ECO2 Systems.
Page 4 of 40
Page 8 of 28
Page 4 of 40
if the Cold
o F (50 o C). o F (50 o C).
F (50 C).
o o
o F (50 o C).