Table of Contents
Advertisement
Quick Links
MUM2000-2 Multiplexer Uplink Module
Installation Instructions
Document Number MUM2-A2-GZ40-00
September 2004
Contents
Software and Firmware License Agreement
The terms and conditions of this License Agreement (the "Agreement") will apply
to the software and/or firmware (individually or collectively the "Software")
incorporated into the Paradyne product (the "Product") purchased by you and any
derivatives obtained from the Software, including any copy of either. If you have
executed a separate written agreement covering the Software supplied to you
under this purchase, such separate written agreement shall govern.
Paradyne Corporation ("Paradyne") grants to you, and you ("Licensee") agree to
accept a personal, non-transferable, non-exclusive, right (without the right to
sublicense) to use the Software, solely as it is intended and solely as incorporated
MUM2-A2-GZ40-00
................................................................................................... 3
............................................................................................. 7
................................................................................................... 8
ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS
TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED
INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU
SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.
IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS
LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS
ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE
LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE
LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU
WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT
PURCHASED BY YOU.
September 2004
...................................................... 1
.......................................................................... 3
............................................................................... 3
................................................................... 5
................................................................... 6
................................................. 9
........................................... 10
................................ 4
1
Advertisement
Table of Contents
Related Manuals for Paradyne MUM-2000
Summary of Contents for Paradyne MUM-2000
-
Page 1: Table Of Contents
MUM2000-2 Multiplexer Uplink Module Installation Instructions Document Number MUM2-A2-GZ40-00 September 2004 Contents Software and Firmware License Agreement Product Documentation Online Release Notes Unpacking the MUM2000-2 Installing an Uplink Interface Module On the MUM2000-2 Installing the MUM2000-2 in a BAC Connecting the UIM to the Network BAC Management LED Indicators Regulatory Compliance for Class A Equipment... - Page 2 in the Product purchased from Paradyne or its authorized distributor or reseller under the following terms and conditions: 1. Ownership: The Software is the sole property of Paradyne and/or its licensors. The Licensee acquires no title, right or interest in the Software other than the license granted under this Agreement.
-
Page 3: Product Documentation Online
Product Documentation Online Complete documentation for Paradyne products is available at www.paradyne.com. Select Support → Technical Manuals. To order a paper copy of a Paradyne document, or to speak with a sales representative, please call 1-727-530-2000. Release Notes Release notes for this product are available in the subscriber firmware area of www.paradyne.com. -
Page 4: Installing An Uplink Interface Module On The Mum2000-2
Installing an Uplink Interface Module On the MUM2000-2 A Uplink Interface Module (UIM) provides the upstream network connection for the BAC. Neither a BAC nor a MUM2000-2 can function without a UIM. Any of the available Paradyne UIM models may be installed on a MUM2000-2. Uplink Interface Modules Procedure To install a UIM in the MUM2000-2:... -
Page 5: Installing The Mum2000-2 In A Bac
4. Ensure that the mounting holes on the UIM are lined up with the corresponding standoffs on the MUM2000-2 circuit board and that the board-to-board connector key pins are properly aligned. 5. Gently press down with even pressure on all four corners of the UIM until the board-to-board connector is fully seated. -
Page 6: Connecting The Uim To The Network
Connecting the UIM to the Network Connect the network line according to the UIM model type installed in the MUM2000-2. The following sections describe the general procedures. For further information refer to the Installation Instructions for the particular UIM model. UIM-1000T Procedure To connect a UIM-1000T to the network:... -
Page 7: Bac Management
UIM-T1 and UIM-E1 Procedure To connect a UIM-T1 or UIM-E1 to the network: 1. Plug your T1 or E1 cable into the RJ45 port on the UIM-T1 or UIM-E1 faceplate. The UIM-T1 and UIM-E1 connect to a T1 or E1 network extender provider unit (TNE1500-P, TNE1500-P-12, ENE2000-P, or ENE2000-P-12) via the T1 or E1 line. -
Page 8: Led Indicators
LED Indicators Table 1. MUM2000-2 LEDs STATE INDICATION PWR (Power) Solid Green MUM2000-2 is receiving power Pulsing Green* MUM2000-2 is operational Solid Amber MUM2000-2 is receiving power Pulsing Amber* MUM2000-2 is operational No Illumination No power Solid Green All fans are functioning Solid Amber Non-functioning fan Lnk (Link) -
Page 9: Regulatory Compliance For Class A Equipment
Regulatory Compliance for Class A Equipment The following regulatory compliance information applies to a MUM2000-2 as installed in a BAC. US Federal Communications Commission (FCC) Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. -
Page 10: Warranty, Sales, Service, And Training Information
Warranty, Sales, Service, and Training Information Contact your local sales representative, service representative, or distributor directly for any help needed. For additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or Paradyne worldwide office locations, use one of the following methods: „...