Aiwa AD-6300 Operating Instructions Manual page 5

POWER Button
AC Voltage Selector Switch
This has been pre-set for AC 220—240 V. To employ this set -
with AC 110—120 V power, use a pin or slotted screwdriver to
change the rear panel Voltage Selector Switch setting to the AC
110—120 V position.
TAPE SELECTOR Switches
The bias and equalization must match the employed tape in
order to fully benefit from its properties. Set the BIAS and EQ
switches according to tape type as indicated below,
Recordin! TAPE SELECTOR
зае g Record and playback
BIAS EQ
= —CrO, Tape
\ 70 )=— Fe-Cr Таре
Е = 120 )=— LH or Standard Tape
% NORMAL „sec
About the automatic changeover device of CrO2 cassette
tape
Now commercially available is a CrO2 cassette tape provided
with the device designed to unnecessitate manual changeover of
the equalizer or bias current.
This device is a groove located alongside of the rear tab provided
to prevent accidental erasure of the recorded tape. When a CrO2
provided with this groove is used, it is not necessary to change
over the equalizer or bias current manually. As a rule, this groove
is made to internationally common specifications, so any CrO2
cassette tape with such a groove can readily be used regardless of
the brand.
w/ Automatic changeover Device
w/o Automatic changeover Device —
HOW TO INSTALL CASSETTE
1) Remove the tape stopper used to hold the tape packed
securely in a cassette.
Press the STOP/EJECT Key to open the Cassette Case of the
set.
2
3) Putting the surface desired to playback downwards ahead,
the visible side of tape shall be inserted by making it
downwards.
4) Close the Cassette Case securely.
Playing Tape
1) Set EQ TAPE SELECTOR switch position (the BIAS switch
setting does not affect playback).
e Setto LH: To play standard or LH tape
е Set to Fe-Cr: To play Fe-Cr tape
e SettoCrO,: To play CrO, tape
е Set to LH: To play most commercially recorded
tapes
Select DOLBY NR switch position
e Setto ON: To play Dolby recorded tape
е Set to OFF: To play normally recorded tape
3) Press FWD key.
4) Adjust the OUTPUT LEVEL control of this set, and the
volume, tone and balance controls of the connected stereo
amplifier as required for comfortable listening.
2
TAPE FAST FORWARD, REWIND, STOP
e Press the F.FWD/CUE key for tape fast forward.
e To rewind the tape, press the REW/REVIEW key.
е To stop the tape, press the STOP/EJECT key.
Automatic Stop System
When the tape is completely wound in Record, Playback, Fast
Forward or Rewind, the Automatic Stop mechanism becomes
activated to stop the tape and return the control button(s) to the
neutral position.
PAUSE Key
Press and lock the PAUSE key to temporarily stop the tape
during playback or recording. Press the key again to release it
and resume tape motion.
CUE/QUICK REVIEW
Fast forward or rewind can be performed from playback or
recording without releasing the FWD key. During playback, press
and hold down the F.FWD/CUE or REW/REVIEW key to
quickly wind the tape to the desired position, then release the
key. The desired passage can be recognized from its speeded up
sound and playback resumed immediately. If this is performed
during recording, the RECORD key becomes released.
=
QUICK REVIEW
De
To Perform Recording
е Check that all connections are correct.
1) Install cassette.
2) Set the BIAS and EQ TAPE SELECTOR
switches according
to the type of tape.
3) Select DOLBY NR switch position.
4) Select INPUT SELECTOR switch position.
e
Setto LINE:
To record from LINE IN jacks
e
Setto MIC/DIN:
То record from either DIN jack
е Set to MIC/DIN:
To record from microphones
5) Press down and lock the PAUSE key.
6) While holding the RECORD
key down, press the FWD key.
е « > b> в и
RECORD REW/REVIEW FWD FFWD/CUE STOP/EJECT PAUSE
QA