Table of Contents
Advertisement
Quick Links
Page
Contents
2
1.
3
2.
4
3.
4
5
5
5
7
4.
7
8
9
10
5.
11
6.
HY B-EYE K15 AQUA
INSTRUCTION MANUAL
INDEX
Congratulations on choosing a Claypaky product!
We thank you for your custom.
Please note that this product, as all the others in the
rich Claypaky range, has been designed and made with
total quality to ensure excellent performance and best
meet your expectations and requirements.
1
CL3030
Advertisement
Table of Contents
Related Manuals for ARRI CLAYPAKY HY B-EYE K15 AQUA
Summary of Contents for ARRI CLAYPAKY HY B-EYE K15 AQUA
-
Page 1: Table Of Contents
HY B-EYE K15 AQUA CL3030 INSTRUCTION MANUAL INDEX Congratulations on choosing a Claypaky product! Page Contents We thank you for your custom. Safety information Please note that this product, as all the others in the rich Claypaky range, has been designed and made with Unpacking and preparation total quality to ensure excellent performance and best Installation and start-up... -
Page 2: Safety Information
1. SAFETY INFORMATION SAFETY INFORMATION IMPORTANT: Claypaky recommends you carefully read and keep the safety information on this product, also available in digital format at the following link: www.claypaky.com Ref: [FIS023 - Safety information Hy B-Eye K15 Aqua] INFORMAZIONI DI SICUREZZA IMPORTANTE: Claypaky raccomanda di leggere accuratamente e conservare le informazioni di sicurezza relative a questo prodotto, sempre reperibili in versione digitale al seguente link: www.claypaky.com... -
Page 3: Unpacking And Preparation
2. UNPACKING AND PREPARATION 2 x 183102/805 Packing contents - Fig. 1 LOCKED UNLOCKED PAN Mechanism Lock and Release (every 90°) - Fig. 2 TILT Mechanism Lock and Release (every 45°) - Fig. 3 HY B-EYE K15 AQUA... -
Page 4: Installation And Start-Up
3. INSTALLATION AND START-UP 3.1 Installing the fixture Installing the projector - Fig. 4 The projector can be installed on the floor on a truss or on the ceiling or wall. WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request). This must be securely fixed to the support structure of the projector and then connected to the fixing point.. -
Page 5: Connecting To Manis Supply
3.2 Connecting to manis supply Mains Connecting to the mains supply - Fig. 6 3.3 Connecting the control signal line: DMX / Art-Net DMX 512 5 PIN SCREEN SIGNAL SIGNAL Ethernet Connecting to the control signal line (DMX) - Fig. 7 Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. - Page 6 Reversal of the display - Fig. 9 To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again. Setting the projector starting address On each projector, the starting address must be set for the control signal (addresses from 1 to 512).
-
Page 7: Maintenance
4. MAINTENANCE 4.1 Maintenance and Caution Light collimation system This product contains internal light collimation system. Avoid intense light from any angle. Periodical cleaning Periodical cleaning WARNING - IP 66 fixture - Failure to completely remove power from fixture prior to servicing can lead to serious injury or death. For additonal service information please contact service@claypaky.it IMPORTANT The screws to be removed have rubber sleeve gaskets at the threaded end of the screw. -
Page 8: Battery Removal
4.2 Battery removal Battery removal - Fig. 11 This product contains a rechargeable battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. HY B-EYE K15 AQUA... -
Page 9: Opening The Covers
4.3 Opening the covers Opening the covers - Fig. 12 HY B-EYE K15 AQUA... -
Page 10: Dimensions
5. DIMENSIONS Hy B-Eye K15 Aqua (16.42") (13.97") (16.02") (22.56") (22.52") (15.35") (11.61") HY B-EYE K15 AQUA... -
Page 11: Cause And Solution Of Problems
6. CAUSE AND SOLUTION OF PROBLEMS THE PROJECTOR WILL NOT SWITCH ON ELECTRONICS NON-OPERATIONAL PROBLEMS DEFECTIVE PROJECTION REDUCED LUMINOSITY POSSIBLE CAUSES CHECKS AND REMEDIES No mains supply. Check the power supply voltage. LED exhausted or defective. Call an authorised technician. Signal transmission cable faulty or disconnected. - Page 12 www.claypaky.com – Service support & Helpdesk: https://e-assist.tech...