ARRI Claypaky AXCOR PROFILE 400 Instruction Manual
  1. Manuals
  2. Brands
  3. ARRI Manuals
  4. Light Fixture
  5. Claypaky AXCOR PROFILE 400
  6. Instruction manual
ARRI Claypaky AXCOR PROFILE 400 Instruction Manual

ARRI Claypaky AXCOR PROFILE 400 Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Page
Contents
2
1.
3
2.
4
3.
4
4
5
5
7
4.
7
8
9
12
14
4.5 Rotating gobos
15
16
5.
AXCOR PROFILE 400
AXCOR PROFILE 400 HC
INSTRUCTION MANUAL
INDEX
Congratulations on choosing a Claypaky product!
We thank you for your custom.
Please note that this product, as all the others in the
rich Claypaky range, has been designed and made with
total quality to ensure excellent performance and best
meet your expectations and requirements.
C61769
C61768

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Claypaky AXCOR PROFILE 400 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ARRI Claypaky AXCOR PROFILE 400

Summary of Contents for ARRI Claypaky AXCOR PROFILE 400

  • Page 1: Table Of Contents

    AXCOR PROFILE 400 C61769 AXCOR PROFILE 400 HC C61768 INSTRUCTION MANUAL INDEX Congratulations on choosing a Claypaky product! Page Contents We thank you for your custom. Safety information Please note that this product, as all the others in the rich Claypaky range, has been designed and made with Unpacking and preparation total quality to ensure excellent performance and best Installation and start-up...

  • Page 2: Safety Information

    1. SAFETY INFORMATION SAFETY INFORMATION IMPORTANT: Claypaky recommends you carefully read and keep the safety information on this product, also available in digital format at the following link: www.claypaky.com Ref: FIS00T - Safety Information Axcor 400 series INFORMAZIONI DI SICUREZZA IMPORTANTE: Claypaky raccomanda di leggere accuratamente e conservare le informazioni di sicurezza relative a questo prodotto, sempre reperibili in versione digitale al seguente link: www.claypaky.com...

  • Page 3: Unpacking And Preparation

    2. UNPACKING AND PREPARATION 2 x 183102/805 Packing contents - Fig. 1 UNLOCKED LOCKED PAN Mechanism Lock and Release (every 90°) - Fig. 2 TILT Mechanism Lock and Release (every 45°) - Fig. 3 AXCOR PROFILE 400 - 400 HC...

  • Page 4: Installation And Start-Up

    3. INSTALLATION AND START-UP 3.1 Installing the fixture Installing the projector - Fig. 4 The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall. WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/001 available on request). This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.

  • Page 5: Connecting The Control Signal Line: Dmx / Art-Net

    Mains Connecting to the mains supply - Fig. 6 3.3 Connecting the control signal line: DMX / Art-Net DMX 512 5 PIN SCREEN SIGNAL SIGNAL Connecting to the control signal line (DMX) - Fig. 7 Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified.
  • Page 6 Reversal of the display - Fig. 9 To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again. Setting the projector starting address On each projector, the starting address must be set for the control signal (addresses from 1 to 512).

  • Page 7: Maintenance

    4. MAINTENANCE 4.1 Opening the covers 1/4 Turn 1/4 Turn Locking and releasing Pan and Tilt movements - Refer to the instructions in the UNPACKING AND PREPARATION section. Opening the head covers - Fig. 10. Closing the head covers - Fig. 11. ‘...

  • Page 8: Periodical Cleaning

    4.2 Periodical cleaning NOTE: keep a careful cleaning Upper side of the ''CMY/colour filters assembly'' to prevent rapid deterioration. Light collimation system This product contains internal light collimation system. Avoid intense light from any angle. Lower side Periodical cleaning - Fig. 12 To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits.

  • Page 9: Effects Module Removal

    4.3 Effects module removal Upper side Extraction of the effect modules - Fig. 13. IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. Insertion of the effect modules: Repeat the operations indicated in Fig. 13, 14 and 15 in reverse order. NOTE: - Do not disconnect wiring harnesses when the fixtures is switched-on, to avoid to damage electronic boards.
  • Page 10 Upper side Extraction of the effect modules - Fig. 14. IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. Insertion of the effect modules: Repeat the operations indicated in Fig. 13, 14 and 15 in reverse order. NOTE: - Do not disconnect wiring harnesses when the fixtures is switched-on, to avoid to damage electronic boards.
  • Page 11 Upper side Extraction of the effect modules - Fig. 15. IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. Insertion of the effect modules: Repeat the operations indicated in Fig. 13, 14 and 15 in reverse order. NOTE: - Do not disconnect wiring harnesses when the fixtures is switched-on, to avoid to damage electronic boards.

  • Page 12: Cleaning Of The Filters

    4.4 - Cleaning of the filters 1/4 Turn Cleaning of the filters - Fig. 16. AXCOR PROFILE 400 - 400 HC...
  • Page 13 1/4 Turn Cleaning of the filters - Fig. 17. AXCOR PROFILE 400 - 400 HC...
  • Page 14 4.5 - Rotating gobos Bearing group replacement - Fig. 18 1 ±0.1 INDEX Replacing rotating gobos - Fig. 19 - Before use custom gobos contact Claypaky; - The original gobos have a special coating designed specifically to resist to the high temperatures; - The rotating gobo wheel only use dichroic glass gobos (it is not possible to use metal gobos);...

  • Page 15: Battery Removal

    4.6 Battery removal Battery removal - Fig. 21 This product contains a rechargeable battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. AXCOR PROFILE 400 - 400 HC...

  • Page 16: Dimensions

    5. DIMENSIONS (19.29") (18.50") (14.80") (25.47") (20.90") (13.78") (10.83") CAUSE AND SOLUTION OF PROBLEMS THE PROJECTOR WILL NOT SWITCH ON ELECTRONICS NON-OPERATIONAL PROBLEMS DEFECTIVE PROJECTION REDUCED LUMINOSITY POSSIBLE CAUSES CHECKS AND REMEDIES No mains supply. Check the power supply voltage. LED engine defective.

This manual is also suitable for:

Claypaky axcor profile 400 hcC61769C61768

Table of Contents