External Control Settings - Yamaha UD-Stomp User Manual

External Control Settings

The ASSIGNABLE CONTROL knob on the top panel can be used to control any one of the
effect's parameters. You can also use a foot controller (Expression Pedal) (optional) such as
the Yamaha FC-7, etc., connected to the EXP. PEDAL jack or an external MIDI device con-
nected to the MIDI IN jack to control UD-Stomp parameters.
* In this section, some button names have been shortened, for instance [EFFECT BAND 1] button is written as [BAND 1] button.
I Procedure
1. In the Play Mode, simultaneously press the
[FUNCTION] button and the [WAVE] button.
Enter the external control setting mode and
CtL
" " will appear on the display.
2. Press the [BAND 1] button.
A control number will appear on the display.
Use the [UP]/[DOWN] buttons to set the control
number.
Up to 8 programmed control settings can be as-
signed to control numbers 1-8 in the UD-Stomp.
A separate controller can be used to control each
programmed control setting or a single controller
can be used to control all control settings sepa-
rately.
3. Press the [BAND 2] button.
The controller type will appear in the display.
Use the [UP]/[DOWN] buttons to set the type of
controller.
E. P
• : Control is by the foot controller con-
A. C
• : Control is by the [ASSIGNABLE
1 31
• -
4. Press the [BAND 3] button.
The parameter type will appear in the display.
The number indicates the Effect Band number.
Use the [UP]/[DOWN] buttons to select the pa-
rameter to be controlled.
oFF
• : off (no control)
ti1
• -
LF1
• -
HF1
• -
24
nected to the EXP. PEDAL jack.
CONTROL] knob on the top panel.
64 95
, - : Control is by control
change data received from an ex-
ternal MIDI device connected to the
MIDI IN jack. Select the control
change number. (Refer to the
Owner's Manual for the external
MIDI device for information in MIDI
control change numbers.)
ti8
: TIME (Delay Time)
LF8
: LOW CUT FILTER
HF8
: HIGH CUT FILTER
Fb1 Fb8
• - : FEEDBACK
tP1 tP8
• - : TAP
SP1 SP8
• - : SPEED
dP1 dP8
• - : DEPTH
Pn1 Pn8
• - : PAN
LE1 LE8
• - : LEVEL
EF. L
• : EFFECT LEVEL
di. L
• : DIRECT LEVEL
di. P
• : DIRECT PAN
The controller that was assigned in step 3 can
be used to control these parameters (setting val-
ues).
* The TIME controller listed above alters the delay time be-
tween 0 and 100% without changing the actual delay time
value that is set with the panel knob, so changes resulting
from the TIME controller will not be saved when the patch
is stored.
* Controllers other than TIME, change the value of the cor-
responding parameter so when the patch is stored those
changes will also be saved to memory, rewriting previous
data.
5. Press the [BAND 4] button.
The parameter's adjustable minimum value (the
parameter's value when the controller is set to
its minimum) is shown in the display.
Use the [UP]/[DOWN] buttons to set the value.
6. Press the [BAND 5] button,
The parameter's adjustable maximum value (the
parameter's value when the controller is set to
its maximum) is shown in the display.
Use the [UP]/[DOWN] buttons to set the value.
7. Press the [FUNCTION] button to return to the
Play Mode.
These external control settings are saved
with patch data.
Also, there are other functions not related to
patch settings that set the Utility Mode's Ex-
ternal Controller to always ON (active) or set
the External Controller to always OFF (inac-
tive). (→ page 26)