Table of Contents
Advertisement
Convenient Functions
Here are some convenient functions that make using the UD-Stomp easier.
G Use the Footswitch to set the Delay
Time (Tap Tempo)
With the UD-Stomp you can tap on the Footswitch
to set the Delay Time parameter.
1. Step on and hold the BANK Footswitch until
tAP
"
" appears in the display.
2. Step on Footswitch 1 and select the Effect Band
to which you want to set the delay time.
* When multiple delays are combined into a Group, only the
Effect Band at the head of the group can be selected. If the
[EFFECT BAND 1-8] buttons on the panel are used to select
any other Effect Band, the Tap Tempo function can not be
carried out.
3. Use Footswitch 2 to switch the selected Effect
Band ON/OFF.
* Each Effect Band has two switches, one on the effect input
side, another on the output side, that can be used to switch
the Effect Band ON/OFF.
SW1
• When the currently selected Effect Band is set OFF, step-
ping on Footswitch 2 will switch both SW1 and SW2 ON
and the Effect Band will be switched ON (the Footswitch
2 lamp lights).
• When the currently selected Effect Band is set ON, step-
ping on Footswitch 2 will switch only SW1 OFF (SW2 is
still ON) (the Footswitch 2 lamp flashes). The delay that
is present up until Footswitch 2 was depressed will con-
tinue to sound but the delay circuit will not accept addi-
tional input.
• When only SW1 in the currently selected Effect Band is
switched OFF, stepping on Footswitch 2 will switch SW1
ON. In this condition both SW1 and SW2 are switched
ON which means that the Effect Band is also ON (the
Footswitch 2 lamp lights).
• To switch the Effect Band OFF, hold the desired [EFFECT
BAND 1-8] button on the panel.
4. Step (tap) on Footswitch 3 in the tempo you want
to set the delay time to.
* In step 4, the Delay Time will be rewritten every time the
Footswitch is pressed.
22
Effect Band Number
Effect Band
SW2
5. Step on the BANK Footswitch to return to the
Play Mode.
G Loop Sampling
With the UD-Stomp, you can sample a phrase (the
input signal) that will playback in a loop (the phrase
will continue to playback, feedback is unlimited).
1. Step on the BANK Footswitch until "
pears in the display.
2. Step on Footswitch 1 and select an Effect Band
that has sufficient delay time required for the
phrase you want to record.
* When multiple Effect Bands are grouped to form a long delay
time, only the Effect Band at the head of the group can be
selected. If the [EFFECT BAND 1-8] buttons on the panel
are used to select any other Effect Band, the Loop Sampling
function can not be carried out.
3. Step on and hold Footswitch 2 until "
the selected Effect Band number) appears in the
display.
The display flashes and the Loop Sampling func-
tion is in standby mode (maximum delay time,
SW1=OFF, SW2=ON, RAM clear).
4. Step on Footswitch 3 (SW1=ON) to start sam-
pling, and release the switch to stop sampling
(SW1=OFF, FEEDBACK=10)
The delay time is set according to the length of
time that the Footswitch is depressed (from when
you step on it until it's released), and the phrase
you play is recorded while the Footswitch is held
down. When the Footswitch is released, the
phrase starts continuous playback.
* If the length of the sample exceeds the set delay time, the
sample will be ignored.
5. If you want to mix another phrase into the sample,
first step and release (quickly) on Footswitch 2
(SW1=ON) then add new material on top of your
previous phrase. Once you are done adding to
the loop, step and release (quickly) on Footswitch
2 again (SW1=OFF).
6. To stop playback of the loop sample, first step
on Footswitch 2 until "
play (clear the sample), and the step on the
BANK Footswitch to return to the Play Mode.
tAP
" ap-
LS.
? " (?=
LS.
? " appears in the dis-
Hide quick links:
Advertisement
Table of Contents
