Page 3
RTL8762G Evaluation Board V2 model A User Manual Revision History Date Version Comments Author Reviewer 2023/11/22 V1.0 First version Sillo Copyright 2023 Realtek Semiconductor Corporation. All Rights Reserved.
The RTL87x2G evaluation board V2 model A provides a hardware environment for user development, including: 1. 5V to 3.3V&1.8V power module 2. Support QSPI display interface 3. Audio module (AMIC&DMIC) 4. LED&RGB module 5. FT232 for USB to UART Copyright 2023 Realtek Semiconductor Corporation. All Rights Reserved.
EVB contains the following user interfaces as shown in Figure 1-1, Figure 1-2, Figure 1-3 and Figure 1-4, which marks 22 components with red rectangles. Figure 1-1 EVB blocks distribution Diagram-Front Figure 1-2 EVB blocks distribution Diagram-Back Copyright 2023 Realtek Semiconductor Corporation. All Rights Reserved.
Page 8
RTL8762G Evaluation Board V2 model A User Manual Figure 1-3 EVB interfaces distribution Diagram-Front Figure 1-4 EVB interfaces distribution Diagram-Back Copyright 2023 Realtek Semiconductor Corporation. All Rights Reserved.
Figure 1-5 RTL8762GRH & RTL8762GKU daughterboard Figure 1-6 RTL8762GC & RTL8777G daughterboard 1.2.3 Power Mark 4: USB socket CON1, connect USB to 87x2G, used for 87x2G USB communication and as the external charger power source. Copyright 2023 Realtek Semiconductor Corporation. All Rights Reserved.
Page 10
1.2.4 IO It is designed to connect peripheral devices with IO ports or provide IO test points. Mark 10: JP3, 2x15 pin header, IO jumper Mark 16: JP4, 2x12 pin header, IO jumper Copyright 2023 Realtek Semiconductor Corporation. All Rights Reserved.
EVB. Any SWD interface can be used for SWD debugging. Figure 1-10 SWD interface Mark 6: Microphone socket is shown in Figure 1-11, which can support 3.5mm audio connector. Copyright 2023 Realtek Semiconductor Corporation. All Rights Reserved.
Page 12
Mark 10: 24bit SDADC interface, as shown in Figure 1-13. Support two differential input, AIN0 and AIN1 are a pair of differential inputs, AIN2 and AIN3 are a pair of differential inputs. Figure 1-13 24bit SDADC interface Copyright 2023 Realtek Semiconductor Corporation. All Rights Reserved.
Page 13
Mark 14: LED&RGB interface, as shown in Figure 1-15, including four red LED and a RGB LED. The LED&RGB can be controlled by placing the jumpers on the yellow box, or by connecting it to any GPIO. Figure 1-15 LED&RGB interface Mark 8: QDECODE interface. Copyright 2023 Realtek Semiconductor Corporation. All Rights Reserved.
Figure 1-17 GPIO button 1.3 EVB motherboard pin assignment There is an anti-reverse insertion mechanism between motherboard and daughterboard. Please refer to the latest RTL87x2G_IOPin_Information table about the pin assignment of daughterboard. Copyright 2023 Realtek Semiconductor Corporation. All Rights Reserved.
P3_0 to FT232_RX, P3_1 to FT232_TX by jumpers, as shown in Figure 2-2. After downloading, select the dial switch to “1” position, which will pull none P0_3, then press reset button or power on again, the program will start running normally. Figure 2-2 Download connection Copyright 2023 Realtek Semiconductor Corporation. All Rights Reserved.
Mark 2: Screen power select, select from CON2/CON1/Lithium battery to power on the screen. Mark 7: Screen interface select, need to set the status of LCD_IM[1:0] based on used screen,please refer to the datasheet of screen for details. Figure 2-4 Display connection Copyright 2023 Realtek Semiconductor Corporation. All Rights Reserved.