Table of Contents
Advertisement
Available languages
Available languages
English
•
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
•
Connect the charger to a mains supply that is properly
connected to earth. Socket and extension cord must have an
operative protective conductor.
•
When operating the charger in damp environments
is unavoidable, use a residual current device (RCD).
The use of a residual current device (RCD) reduces the risk of
electric shock.
•
Children should be supervised to ensure that they do not play
with the appliance.
•
Charger shall not be exposed to dripping or splashing; no
objects filled with liquids, such as vases, shall be placed on it.
•
No exposed flame sources, such as lighted candles, should be
placed on the charger.
•
Mains plug is used as the disconnect device; the disconnect
device (plug) shall remain readily operable.
Grounding Instructions
The charger must be grounded. In the event of malfunction or
breakdown, grounding provides a path of least resistance for
electric current to reduce the risk of electric shock. The charger
is equipped with a cord having an equipment‑grounding
conductor and a grounding plug. The plug must be plugged
into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
DANGER: Improper connection of the
equipment‑grounding conductor can result in a risk of
electric shock. The conductor with insulation having
an outer surface that is green with yellow stripes is the
equipment‑grounding conductor. If repair or replacement
of the cord or plug is necessary, do not connect the
equipment‑grounding conductor to a live terminal.
Repairs shall only be performed by a D
agent. Do not modify the plug provided with the charger –
if it will not fit the outlet, have a proper outlet installed by
a D
WALT repair agent.
e
For grounded, cord‑connected charger rated 16A
and lower and intended for use on a nominal
230V supply circuit
The charger is for use on a nominal 230 V circuit, and
has a grounding plug that looks like the plug in the
following illustration.
DWST83471 ‑QW
DWST83470‑GB
SAVE THESE INSTRUCTIONS
6
USB Charging Port Safety Warnings
•
•
•
•
Residual Risks
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
•
•
•
•
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
i
on the rating plate.
If the supply cord is damaged, it must be replaced only by
D
WALT service
e
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
•
•
•
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
DWST83472‑XE
Using an Extension Cable
If an extension cable is required, use an approved 3–core
extension cable suitable for the power input of this tool (see
Technical Data).The minimum conductor size is 1.5 mm
maximum length is 30 m.
When using a cable reel, always unwind the cable completely.
The USB charging port is not intended for any use other
than supplying power/charging small USB electronics.
Any other uses may result in risk of fire, electric shock or
electrocution.
Do not expose the USB charging port to rain or snow.
When operating the USB charging port outdoors, always
provide a dry location.
Do not operate the USB charging port charger has
received a sharp blow, been dropped or otherwise
damaged in any way. Take the product to an authorized
service center.
WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA or less.
Impairment of hearing.
Risk of personal injury due to flying particles.
Risk of burns due to accessories becoming hot
during operation.
Risk of personal injury due to prolonged use.
SAVE THESE INSTRUCTIONS
Your D
WALT tool is double insulated in accordance
e
with EN62841; therefore no earth wire is required.
WALT or an authorised service organisation.
e
Safely dispose of the old plug.
Connect the brown lead t o the live terminal in the plug.
Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made to the
earth terminal.
2
; the
Advertisement
Table of Contents
