Table of Contents
Advertisement
Quick Links
Z Series Prep Tables
Base Models:
#178ZPT27HC
#178ZPT36MWMS
#178ZPT27HCA
#178ZPT36WMS
#178ZPT27MHC
#178ZPT48HC
#178ZPT27MWMS
#178ZPT48MHC
#178ZPT27WMS
#178ZPT48MWMS
#178ZPT36HC
#178ZPT48WMS
#178ZPT36MHC
#178ZPT60HC
Note:
Please read the manual thoroughly prior to equipment setup, operation, and maintenance.
www.AvantcoRefrigeration.com
User Manual
#178ZPT60MHC
#178ZPT60MWMS
#178ZPT60WMS
#178ZPT71HC
#178ZPT71MHC
#178ZPT71MWMS
#178ZPT71WMS
02/2024
178ZPT36HC
Advertisement
Table of Contents
Related Manuals for Avantco Z Series
Summary of Contents for Avantco Z Series
- Page 1 User Manual 02/2024 178ZPT36HC Z Series Prep Tables Base Models: #178ZPT27HC #178ZPT36MWMS #178ZPT60MHC #178ZPT27HCA #178ZPT36WMS #178ZPT60MWMS #178ZPT27MHC #178ZPT48HC #178ZPT60WMS #178ZPT27MWMS #178ZPT48MHC #178ZPT71HC #178ZPT27WMS #178ZPT48MWMS #178ZPT71MHC #178ZPT36HC #178ZPT48WMS #178ZPT71MWMS #178ZPT36MHC #178ZPT60HC #178ZPT71WMS Note: Please read the manual thoroughly prior to equipment setup, operation, and maintenance.
-
Page 2: Table Of Contents
User Manual Refrigerated Prep Tables Table of Contents Warnings ..........................3 Installation ..........................4 Cabinet Location Guidelines ................... 4 Electrical ..........................5 Adjusting the Temperature ....................5 Controller ..........................6 Safety / Warning ......................... 7 Loading Food Pans ......................7 Operation / Maintenance .................... -
Page 3: Warnings
User Manual Refrigerated Prep Tables Warnings DANGER – RISK OF FIRE OR EXPLOSION. FLAMMABLE REFRIGERANT USED. TO BE REPAIRED ONLY BY TRAINED SERVICE PERSONNEL. DO NOT PUNCTURE REFRIGERANT TUBING. PELIGRO – RRIESGO DE INCENDIO O EXPLOSION. REFRIGERANTE INFLAMABLE UTILIZADO. PARA SER REPARADO SOLAMENTE POR PERSONAL DE SERVICIO CALIFICADO. -
Page 4: Installation
User Manual Refrigerated Prep Tables Installation This unit is intended for use in a temperature-controlled environment less than 75 degrees Fahrenheit and 60% relative humidity. IMPORTANT – Please Read Before Installation: • If the shelf has a raised lip, the lip needs to be installed facing up towards the rear of the cabinet to promote proper air flow. -
Page 5: Electrical
User Manual Refrigerated Prep Tables • Select a location away from heat and moisture-generating equipment. - Ambient temperatures above 75 degrees Fahrenheit may cause the compressor to malfunction. - For optimal performance, this unit should not be used in environments with ambient temperatures exceeding 75 degrees Fahrenheit. -
Page 6: Controller
Your Z Series unit compressor will continue to run when the door is left ajar. After 15 minutes of being left ajar, an audible alarm will sound. At the same time, the display board will Running a Manual Defrost Cycle This unit is pre-programmed to run automatic defrost cycles at preset intervals. -
Page 7: Safety / Warning
User Manual Refrigerated Prep Tables Safety / Warning Please pay close attention to the safety notices in this section. Disregarding these notices may lead to serious injury and/or damage to the unit. ATTENTION • To minimize shock and fire hazards, be sure not to overload outlet. Please designate one outlet for your unit. -
Page 8: Operation / Maintenance
User Manual Refrigerated Prep Tables Operation / Maintenance WARNING: DISCONNECT THE POWER CORD BEFORE CLEANING ANY PARTS OF THE UNIT NOTE: We strongly recommend that any servicing be performed by an authorized service technician. Cleaning the Fan Blades and Motor •... -
Page 9: Food Pan Layouts
User Manual Refrigerated Prep Tables Food Pan Layouts www.AvantcoRefrigeration.com... - Page 10 User Manual Refrigerated Prep Tables Food Pan Layouts www.AvantcoRefrigeration.com...
- Page 11 User Manual Refrigerated Prep Tables Food Pan Layouts www.AvantcoRefrigeration.com...
-
Page 12: Troubleshooting
User Manual Refrigerated Prep Tables Troubleshooting Problem Possible Cause Possible Solution Fuse blown or circuit breaker tripped. Replace fuse or reset circuit breaker. Power cord unplugged. Plug in power cord. Compressor is not running. Thermostat set too high. Set thermostat to lower temperature. Cabinet in defrost cycle.
Need help?
Do you have a question about the Z Series and is the answer not in the manual?
Questions and answers